How to adjust the decimal point of an electronic scale? How to adjust the decimal point of the elect

Electronic scales have a special button to adjust the number of digits.

The electronic scale unit price can be adjusted by one less 0 after the decimal point.

One decimal place can be selected with a graduation value of 0.

5;Two decimal places can be 0.

Two common faults and maintenance skills of electronic scales.

Fault (1), the electronic scale cannot be charged or the charging indicator does not measure or does not respond.

1.Please determine the 110v 220v of the electronic scale firstWhether the voltage switch is adjusted to the same voltage as the power supply, and make sure that the charging cable is securely plugged into the charging dock on the scale.

2.Bad battery.

3.Check the fuse.

Whether it is bad or not. 4.Check whether the charging cable is broken due to external forces.

5.For the second reason or other factors, it is recommended to return it to the dealership for processing.

Fault (2), no action after the electronic scale is turned on?

1.If you use the adaptor, unplug the output of the adapter connected to the scale, and then remove the dry battery.

Attached, if it can be turned on, that is, the adapter is damaged, please replace it.

2.If you are using a dry (accumulator) battery, please confirm whether the voltage of the dry (accumulator) battery is sufficient? If the voltage is insufficient, replace the dry battery (please charge the battery).

3.Whether the scale fuse is defective.

4.The switch or keys may be damaged.

5.Possible failure of electronic components.

6.For the first reason or not for the above reasons, it is recommended to send it back to the dealership for processing.

The following describes several commonly used fault checking methods:

1.Intuitive method.

There are many components on the main circuit board of the electronic scale, and many faults are caused by short circuits, open circuits, poor plug-out contacts, and component pipe angle welding. Therefore, when the pricing scale fails, the circuit board should first be inspected by intuitive feeling: sight, hearing, smell, touch and other methods.

2.Voltage measurement method.

The electronic scale compares the working voltage of the circuit components and each tube angle of the chip with the normal value, and the place where the voltage changes greatly is the place where the fault is located.

3.Short circuit and open circuit method.

The short-circuit method is to short-circuit a certain part of the circuit, and the electronic scale then passes through the oscilloscope.

or the results of a multimeter test to determine the point of failure. The open-circuit method is to disconnect a certain part of the circuit and then measure the resistance, voltage, or current through a multimeter to determine the fault point.

4.Comparative, substitutional methods.

When the electronic scale is faulty checked, the electronic scale is compared with the faulty scale with the help of the instrument, and the fault point can be found out quickly. In addition, if it is suspected that a part such as sensor, circuit board, power supply, keyboard and other parts prepared in the work is damaged, replace it with the prepared part, and then observe whether the result changes, if the display is normal, it means that there is a problem with the original component. The comparison and substitution method can quickly and accurately determine the fault point.

1. In the number setting area on the right side of the electronic scale, press and hold the decimal point button for a few seconds, and release it after "centr" appears.

2. Then press the "8" button, and 75000 will appear in the single column. You can ignore this step and press the "Accumulation" key to enter the next step.

4. This is when the weight value will appear, and this step is more important. Enter the weight of as many weights as you have in your hand, and remember to reserve the number of decimal places. For example, if you have a 5,000g weight, you need to enter 50,000 because there is a 0 left to the decimal point.

If you only enter 5000, only 5000 will be displayed after the correction is completed, with no decimal point. After entering, press the "Accumulation" button to proceed to the next step.

How to adjust the decimal point of the electronic scale The decimal point adjustment method of the electronic scale

Hello dear, glad to answer for you. How to adjust the decimal point of the electronic scale The decimal point adjustment method of the electronic scale 1, press and hold the decimal point key for a few seconds, and release it after the "centr" appears. 2. Then press the number "8" button, the weight bar will appear cap, press the "Accumulation" button to enter the next step.

3. After that, the weight column shows d1, and the single weight column shows 2, and then press the "accumulation" button to enter the next step. 4. At this time, the number of decimal places is displayed, the default factory value, which can be ignored and operated. Press the "Accumulation" key to enter the next step.

5. At this time, the weight value will appear, how many weights there are, enter the weight of how many weights, reserve the number of decimal places, enter it, and then press the "accumulation" key to enter the next step. 6. At this time, LCP will appear in the weight column and OFF will appear in the single weight column. If the single column appears on, you need to press the "zero" button and press "off" to appear.

7. Cal appears in the weight column, 0 appears in the single weight column, and weight value appears in the total number column. Prepare the weights and press the "Total" button to proceed to the next step. 8. Put the weight, wait for a few seconds, the weight bar jumps to the weight when the weight appears, it means that the correction is completed.

Hello! Glad for your question. There are generally two ways to adjust the decimal point of the electronic scale, one is to adjust it directly on the host, and the other is to use the buttons on the scale to adjust.

1. Directly regret the adjustment on the host 1, press the start button of the electronic scale to enter the host interface; 2. Press "Settings" and find "Decimal Point Adjustment"; 3. Use the up and down keys to adjust the number of decimal points and rolls; 4. After the adjustment is completed, press the "OK" button to adjust the decimal point. 2. Use the buttons on the scale to adjust 1. Press the power button of the electronic scale to enter the host interface; 2. Press "Settings" and find "Decimal Point Adjustment"; 3. Press the "Decimal Point Adjustment" button and use the up and down keys to adjust the number of decimal places; 4. After the adjustment is completed, press the "OK" button to adjust the decimal point. Thank you for your question, I hope it will be of some help to you.

I wish you a happy life!

Summary. Hello, I am glad to answer for you, after inquiring about the information, by the main decimal point, there will be a window in °on" with"FF "Change between on" and you can just let go of it!

If it doesn't work, you can press and hold the 'Tiredness Setting* button for three seconds, then press the decimal point, and then a window will appear off, press the tare and it will become on, and then press the Tiredness Setting" and that's it.

In the parameter setting of the electronic scale weighing instrument, there is an adjustment decimal point. Enter this option to adjust the number of decimal places. How to set it up, because different electronic scales have different setting methods, so you need to refer to the information attached to the electronic scale to set up.

How to adjust the decimal point of electronic scales?

Hello, I'm glad to answer for you, I'm answering this question for you, you need to wait patiently for about three minutes, please don't worry.

Hello, I am glad to answer for you, after inquiring about the information, by the main decimal point, there will be a window in °on" with"FF "Change between on" and you can just let go of it! If it doesn't work, you can press and hold the 'Tired Setting* button for three seconds, then press the decimal point, then there will be a window OFF, press the tare and it will become on, and then press the Tired Setting" in the parameter settings of the electronic scale weighing instrument, there is an adjustment of the decimal point. Enter this option to adjust the number of decimal places.

How to set it up, because different electronic scales have different setting methods, so you need to refer to the information attached to the electronic scale to set up.

There is no ON and OFF

I was only 15:94

Hello, I'm glad to answer for you, after querying the information, hold down the decimal point, wait a few seconds, the weight window appears a letter prompt, let go after the appearance can be, I hope the above will help you, thank you.

It should be more than 77 kilograms.

Hello, I'm glad to answer for you, after querying the information, hold down the decimal point, wait a few seconds, the weight window appears a letter prompt, let go after the appearance can be, I hope the above will help you, thank you.

The adjustment of the decimal point of the electronic scale refers to the process of adjusting the number of decimal places when accurately measuring the weight of an object. Generally speaking, there are two ways to adjust the decimal point of electronic scales, one is manual adjustment, and the other is automatic adjustment. The way to manually adjust the decimal point is:

First of all, turn on the power of the electronic scale, then press the setting button, enter the settings menu, find the decimal adjustment menu, select the number of decimal places to adjust, and then press the OK button to complete the decimal adjustment. The method of automatically adjusting the decimal point is: first, turn on the power of the electronic scale, then press the setting key, enter the settings menu, find the automatic decimal point adjustment menu, select the automatic decimal point adjustment, and then press the OK button to complete the decimal point adjustment.

The decimal point adjustment of electronic scales is a very important process to improve the accuracy of measuring the weight of objects in the core of the scale, so as to better meet the needs of users.

Summary. Hello, the decimal point of the electronic scale is adjusted as follows: 1, on off:

The power switch, if the power is turned on in the case of air scale, it will automatically turn off in about 100 seconds. Many electronic scales will use a circular and vertical symbol to indicate the on/off key. 2. Tare or the letter "T" alone indicates :

Clearing, tare keys; Press the Zero Tare button to bring the scale back to zero. Put the utensil on the scale, press this button to reset the scale to zero, and then add liquid to the utensil, the scale only shows the weight of the liquid.

Hello, the decimal point of the electronic scale is adjusted as follows: 1. On off: the power switch, if the power is turned on in the case of empty scale, it will automatically shut down in about 100 seconds.

Many electronic scales will use a circular and vertical symbol to indicate the on/off key. 2. Tare or a single line such as the hidden letter "T" indicates: zero, tare key; Press the clear and tare button to file the hall to bring the scale back to zero.

Put the utensil on the scale, press this button to reset the scale to zero, and then add liquid to the utensil, the scale only shows the weight of the liquid.

I am Qianlong electronic scale, and now the weight display bar is, how can I change it to a pro, 1Turn on the scale switch first, and press and hold the decimal point on the right side of the panel. 2.

Appear on the center of the display and then press the 8 key on the panel, then press the accumulation key to enter the next step of the hidden base. 3.The weight bar on the scale screen will display:

d1, single weight column display 5; The display of 5 watches carries orange to show our accuracy as, and then press the accumulation key in the panel to proceed to the next step. Check whether the appearance of the electronic scale is clean, whether the switch is in good condition, and then check whether the power supply is sufficient, whether the numbers on the instrument are bright, complete and clear, and whether the zero position of the electronic scale is correct. Weight measurement scales usually have weights, and it is relatively accurate to use these weights.

Measurements are made using standard weights of different masses. The weight should be within the range of the electronic scale and measured in turn. During this process, observe whether the number displayed on the display matches the weight, try a few times, find the error, and then make adjustments.

Just follow the steps

Summary. Hello, for your question How to adjust the decimal point of an electronic scale to three digits Answer: 1

The electronic scale can be adjusted, according to the calibration method on the manual of the electronic scale, change the number of decimal places to 3 digits. 2.Take the big red eagle electronic scale as an example3

In the number setting area on the right side of the big red eagle scale, press and hold the decimal point key for a few seconds, and release it when "centr" appears. 4.Then press the "2" key, and 75000 will appear in the single column.

You can ignore this step and press the "Accumulation" key to enter the next step.

Hello, for your question How to adjust the decimal point of an electronic scale to three digits Answer: 1The electronic scale can be adjusted, according to the calibration method on the manual of the electronic scale, the decimal number or the number of points is changed to 3 digits.

2.Take the big red eagle electronic scale as an example3In the number setting area on the right side of the big red eagle electronic scale, press and hold the decimal point button for a few seconds, and after the "centr" appears, the pine group will open the ante.

4.Then press the "2" key, and 75000 will appear in the single column. You can ignore this step and press the "Accumulation" key to enter the next step.

5. At this time, the weight column of the electronic scale will appear: LCP, and the single weight column will appear: OFF.

6. The weight column appears: cal, the single weight column appears: 0, and the total number column appears the hole weight value.

2. The spike oak represents the accuracy of the scale next to the guess. This successfully completes the adjustment of the electronic scale and can be started from scratch.

Precautions for use: 1. It is strictly forbidden to rain bend or rinse with water, if the skin is accidentally wet, wipe it with a dry cloth, and send it for repair as soon as possible when the machine function is not normal; 2. It is strictly forbidden to knock on and hit and under heavy pressure; 3. Do not place in high temperature and humid environment (except for special waterproof and anti-corrosion scales); 4. Do not let sundries invade the machine to avoid damage; 5. If the electronic scale is not used for a long time, the machine must be wiped clean, put into the dry cloth grip stuffy agent wrapped in a plastic bag, the dry battery should be taken out, and the rechargeable battery should be charged every three months to ensure the service life.