What is the reason for the five sounds of the computer alarm The boot cannot be started.

It may be that the memory is not plugged in there.

1. First of all, we conduct a comprehensive check on the connection between the computer monitor and the host, and plug each connection back to see if there is a connection problem.

2. If the fault still exists, then we need to open the chassis to see if the chassis contains metals and other substances, causing a short circuit in the computer host circuit, and then we smell the computer to see if there is a burning smell, and see if there are damaged components around the motherboard and around the CPU.

3. After checking the whole chassis, there is no abnormality in the chassis, then we will dust the chassis.

4. If it can't be turned on, then use the minimum system method, unplug the data cable of the hard disk, floppy drive, and optical drive, and then check whether the computer can be turned on. Then connect the above devices to the computer one by one, when connecting a certain device, the fault will recur, indicating that the fault is caused by this device, and finally focus on checking this device.

5. If the fault still exists, it is likely to be the fault of the memory card, graphics card, CPU, motherboard, etc., at this time, we only need to plug and unplug these hardware, or replace it again, and try to find the cause one by one.

6. If the memory, graphics card, CPU and other devices are normal, then discharge the BIOS, use the isolation method, place the motherboard outside the chassis, connect the memory, graphics card, CPU, etc. for testing, if the computer can be displayed, then install the motherboard into the chassis for testing until the cause of the fault is found. If the fault persists, you need to return the motherboard to the manufacturer for repair.

7. When the computer is turned on and started, the system BIOS starts to POST (power-on self-test), and when a fatal error is detected in a device in the computer, it will control the speaker to send out a sound to report the error. Therefore, there may be a fault that the power is turned on without displaying an alarm sound. If the computer is turned on and there is no alarm sound, the fault can be checked according to the meaning of the BIOS alarm sound to check the faulty device to eliminate the fault.

The computer does not turn on, and the alarm is given after the start-up, and the start-up alarm is regular;

During the POST, if a fault occurs in the computer, it sometimes rings continuously, and different rings represent different error messages.

First long and then short, several long and some short; You can update the following prompts to determine the cause of the computer failure:

award bios

1 Short: The system starts normally. Shows that there is nothing wrong with the machine.

2 Short: General error, please go to CMOS Setup and reset the incorrect options.

1 long and 1 short: There is an error in the memory or motherboard. Try to change the memory, if it still doesn't work, you have to change the motherboard.

1 long and 2 short: The display or graphics card is wrong.

1 long and 3 short: The keyboard controller is wrong. Check the motherboard.

1 Long 9 Short: Motherboard Flash RAM or EPROM error, BIOS corruption. Try a different block of flash ram.

Constant ringing (long sound): The memory module is not plugged in tightly or is damaged. Reinsert the memory module, or replace the memory.

ami bios

1 Short: The memory refresh failed. Replace the memory module.

2 Short: The memory ECC verification error is incorrect. Setting the memory option for ECC check to Disabled in CMOS Setup will solve the problem, but the most fundamental solution is to replace a memory.

3 Short: The basic memory check of the system fails. Change memory.

4 Short: The system clock is wrong.

5 Short: There is an error in the CPU.

6 Short: Keyboard controller error.

7 short: The real mode of the system is wrong and cannot be switched to protection mode.

8 Short: A memory error is displayed. If there is a problem with the display memory, try changing the graphics card.

9 Short: BIOS chip check and error.

1 long and 3 short: memory error. If the memory is damaged, it can be replaced.

1 long and 8 short: A test error is displayed. The monitor cable is not plugged in properly or the graphics card is not plugged in properly.