How to repair the lifting drying rack hand crank if it is broken

1. The hand crank gear is damaged, check that your hand crank is broken, there are two gears in the hand crank, if the gear is broken, replace the gear.

2. The drying rack hand crank is stuck in the line, and the positioning foot of the spring steel bowl is inserted into the corresponding bayonet and compressed, and the cavity should be opened to straighten out the steel wire again and then installed it as it was.

Open the cavity, generally the steel bowl out of place, fiddling can not make too much force, can not lock the rotating parts, into the steel bowl, at this time as long as the steel wire slowly exit.

In this way, you may not necessarily understand that there are generally two situations when the drying rack hand lifter fails, and the local steel wire is bulging after the wire is messy, but fortunately, it will not be broken.

This lifter is very troublesome to fiddle with, the hanger falls by its own weight, the other hand pulls the wire rope outward, after re-winding, and finally the bottom plate is installed, if it is stuck and shakes, it cannot be shaken, it cannot be shaken or the resistance is large when shaking, the coil spring inside fails, and then the steel wire is wound to the axle with an appropriate amount of loading, one end of the spring is hooked to the protrusion in the steel bowl, and the other end of the spring is hooked to the column in the seat, because its inner cavity is small.

Anyway, if the hand crank and drawstring are broken, they can't be lifted, in case they break before they are fresh, and they are not enough to provoke themselves. I'm afraid that it won't look good with what I do, hehe, see more answers".

The hand crank is the heart of the drying rack and is the most critical accessory, because the hand crank is the most complex structure of all accessories, and it is also the most prone to breakage. The function of the hand crank is to drive the drying rod to lift and lower through the wire rope, which is the part with the most movement and friction, so it is easier to be damaged, but at present, various manufacturers are gradually improving the technology of the hand crank.

Remove the hand crank, and if there is no problem with the wire, it is generally enough to rewind it.

Look at your hand crank is broken. There are two gears inside the hand crank, if the gear is broken, you can replace the gear. If the rocker is broken, exit the part that is broken inside, and then replace it with a replacement, as long as it can bite and shake.

1.The hand crank gear is broken.

There are two gears in the hand crank, if the gear is broken, directly replace the gear and it can be used normally.

2.The hand crank does not move or has a lot of resistance.

The wire rope is chaotic, resulting in local steel wire bulging, resulting in shaky or high resistance during operation.

Solution: Remove the hand crank, check whether there is any abnormality in the wire, straighten out the wire with abnormality, and then wind it up again.

3.The wire can't be locked, and the hanger falls on its own.

The steel bowl detached from its original position, causing the coil spring to fail and unable to lock the rotating parts.

Solution: Open the drying rack cavity, hook one end of the spring to the protrusion in the steel bowl, re-wrap it and load it into the bowl; Then hook the other end of the spring to the column in the seat, insert the positioning foot of the spring steel bowl into the corresponding bayonet and press it, and then wind the steel wire to the axle and load it with an appropriate amount, and finally put the bottom plate on.

If your hands-on ability is okay, remove the hand crank, and if the wire is hairless, you can generally rewind it.

Hello dear. There are generally two kinds of hunger and conditions when the hand crank cannot be lowered, which can be repaired according to the following methods: The hand crank gear is damaged:

Disassemble the hand crank, check whether the gear is damaged, if it is damaged, you can replace the gear by yourself, if the gear is not damaged, repair it according to the next article. The two ends of the spring are not aligned: disassemble the hand crank, pay attention to whether the two ends of the spring are aligned with the notch, if not, help it to correct it.

Dear, <>

The above is the answer I summarized for you, I am very happy to serve you, please give me a thumbs up, thank you very much for <>

I hope my stuffy stare will help you, and then I hope you are happy every day, have a good life<> and good luck always accompany <>you

Summary. 1. Common faults Wire rope: damage, fluffing, breakage, unsmooth lifting, and loud noise; Hand crank:

Damaged, loose, broken, wire rope damage, stuck wire rope can't get stuck Top seat: damaged, worn, falling off, broken, pulley cracking Corner: damaged.

1. Common faults Wire rope: damage, fluffing, breakage, unsmooth lifting, and loud noise; Hand crank: damaged, loose, broken, wire rope damage, front crack side card wire rope can not be stuck Top Hui Rubber Seat:

Damage, abrasion, detachment, source pin cracking, pulley cracking Corner: Damaged.

Second, the maintenance method of the wire can not be locked: 1. If this kind of situation occurs, it may cause it to fall by itself by its own weight, mainly because the steel bowl is out of place, and the coil spring inside fails, and the rotating parts cannot be locked. 2. Open the cavity, hook one end of the spring to the protrusion in the steel bowl, re-wrap it, load it into the steel bowl, hook the other end of the spring to the column in the seat, and insert the positioning foot of the spring steel bowl into the corresponding card to talk about the potato key mouth and press it.

Finally, attach the base plate. Shake or shake with high resistance:

<>If my answer is helpful to you, please give a give me a thumbs up (comment in the lower left corner), I look forward to your praise, your efforts are very important to me, and your support is also the driving force for my progress. If you feel that my answer is still satisfactory, you can click on my avatar for one-on-one consultation. Finally, I wish you good health and a happy heart.

The original installation of my house is also hand-cranked, that will be either the crank is bad or the wire rope is easy to break, and then it was simply replaced with an electric one, remote control control, four rods, easy to dry.

Summary. We will be happy to answer your <>

Hello, if the balcony drying rack hand crank is broken, you can consider the following aspects to fix it. 1.Replace the hand crank:

The hand crank is a key component of the balcony drying rack and needs to be replaced if it breaks. You can go to the home building materials market or ** to buy the corresponding hand crank, and then replace it according to the manual. 2.

Check the chain or rope: The hand crank is connected to the drying rack by a chain or rope, and if the chain or rope is broken or loose, it will also cause the hand crank to be unusable. The condition of the chain or rope can be inspected and replaced if there is a problem.

3.Adjust the position of the hand crank: Sometimes the hand crank does not work because it is not in the correct position and the hand crank needs to be repositioned.

In addition to the above aspects, you can also pay attention to the following points when using balcony drying racks: do not use overweight, do not use excessive force, do not use improper use, etc. This effectively extends the life of the balcony drying rack and reduces the possibility of problems with the hand crank.

How to repair the broken hand crank of the balcony drying rack.

We will be happy to answer your <>

Hello, if the balcony drying rack hand crank is broken, you can consider the following aspects to fix it. 1.Replace the hand crank:

The hand crank is a key component of the balcony drying rack, and if it breaks, it needs to be replaced. You can go to the home building materials market or ** to buy the corresponding hand crank to check the oak, and then replace it according to the manual. 2.

Check the chain or rope: The hand crank is connected to the drying rack by a chain or rope, and if the chain or rope is broken or loose, the hand crank will not work. The condition of the chain or rope can be inspected and replaced if there is a problem.

3.Adjust the position of the hand crank: Sometimes the hand crank does not work because it is not in the correct position and the hand crank needs to be repositioned.

In addition to the above aspects, you can also pay attention to the following points when using balcony drying racks: do not use overweight, do not use excessive force, do not use improper use, etc. This effectively extends the life of the balcony drying rack and reduces the possibility of problems with the hand crank.

I can't get on the hanger.

What to do? Hello, if your cooler can't go up, the forward roll can be caused by loose or damaged connecting parts of the cooler. You can check if the connection is loose or falling off, and if so, you can try to re-tighten the connection.

If there is no problem with the connecting part, it may be that there is a problem with the structure of the cooler and it needs to be replaced or repaired. In addition, it is recommended to avoid overweight or imbalance when using the cooler to avoid excessive pressure and damage to the cooler. At the same time, it is also very important to regularly inspect and maintain the cooler to prolong the service life of the cooler and ensure safety.

1. If the hand lifter can't shake, or just the resistance is very large, it is generally caused by the internal steel wire disorder, the user needs to slowly withdraw the steel wire, straighten it and then retract it, if the steel wire has been completely stuck in the owner, then you need to open the slippery cavity belief bend the steel wire. 2. If the hand lifter fails, and the drying rack falls because of its own weight, this situation is because the internal coil spring fails, and the user needs to open the cavity and replace the new spiral tung spring.