How to strengthen the folding drying rack at home if it is always poured out?

The drying rack at home is overturned, mainly in the following situations:

The load-bearing capacity is not very good, and when the clothes hanging on it are heavy, the folding drying rack cannot bear more weight than it can handle, so when there are too many clothes to dry, the clothes need to be dried in batches.

The structural connection is not strong, and the key parts can only be strengthened in the later stage, and if conditions permit, the bottom of the folding drying rack can be reinforced.

In addition, if the economic conditions allow, it is recommended to buy smart drying racks from well-known brands such as Lianqing, which have good quality, complete functions and high overall cost performance.

Taking Lianqing intelligent drying rack as an example, in terms of material, the fuselage and drying rod are made of aluminum alloy materials with good hardness, and the wire rope is made of 7x7 strands of 15mm diameter national standard 304 wire rope, which has high strength, good toughness and durability; In terms of function, it has the functions of automatic lifting, air drying, drying, disinfection, voice control, APP, etc., making the drying operation more convenient and practical; On the **, between 1000 yuan and 5000 yuan, compared with similar products of other brands, it is more cost-effective.

The drying rack may be that the clothes you are drying are too heavy, if the conditions permit, fix the legs on the ground with clips and hit the ground, if it still doesn't work, you can change it, such as the folding of the colorful years, the drying rack, there is no such problem, there is reinforcement, it mainly depends on yourself, I hope mine is helpful to you.

Summary. What should I do if the pole of the X-shaped floor-standing folding drying rack is broken? Hello, glad to answer for you, yes. Repair the hero universal repair belt can be. Simple winding can be repaired.

What should I do if the pole of the X-shaped floor-standing folding drying rack is broken? You're hungry and I'm glad to call you to answer the letter, and Sakura can. Repair the hero universal repair belt can be. Simple winding can be repaired.

Can it be repaired? It was the place where the X figure was fixed.

Twist 1, first prepare a pair of needle-nose pliers or vices; 2. Clamp the steel wire that has been sorted out with pliers, and pull it out hard. Note that the cover book Huai Yi, do not clinch the tightrope in a posture. 3. At the same time, the other hand shakes the handle to release the wire, and the direction of rotation should be determined according to the observation.

Sometimes, contrary to the normal steering, the wire can be released, and everything should be carefully checked to see the direction of the wire on the spool. Note that in the process, the hand holding the wire should also be pulled outward with strength. This step is the hardest part, take your time and do it a few more times.

4. When the wire is completely pulled out, you still can't loosen the pliers, let the wire stretch, and then slowly shake the handle to retract the wire little by little.

Many friends mistakenly believe that the drying rack is installed after the suspended ceiling is completed. In fact, this practice is incorrect. Mainly because the ceiling part cannot bear the weight, usually, the clothes on the drying rack are very heavy, so the drying rack needs to be fixed on the top of the wall (floor, beam, etc.) to install safely.

If you accidentally install the ceiling first and then install the lifting drying rack, there is a maintenance problem, everyone knows that the drying rack is a combination of slide rail and wire, sometimes it is inevitable to derail, if there is a derailment, it will be troublesome, the ceiling will be removed, otherwise the drying rack will become a decoration, in addition, the steel wire and base of the lifting drying rack, the pulley will be exposed to the outside, it will appear more messy.

Drying rack installationModern family balcony ceilings mostly use aluminum gusset or PVC gusset. Generally, the upper limit of leaving the balcony is about 10cm, and in this case, it is necessary to automatically lift the drying rack to install it. The automatic lifting drying rack is fixed by expansion screws at the top of the ceiling, and the balcony ceiling itself does not have a large load capacity.

Therefore, if the balcony ceiling ceiling, can not be directly repaired lifting drying rack automatically installed on the ceiling keel, a good installation method is to directly repair the antenna floor on the line through the ceiling ceiling decorations, the distance between the two laughing Sengen drying rods depends on the width of the balcony, generally 45-50cm, ultra-wide balcony, can be appropriately widened; The distance between the two lifting balls of each drying rod is generally about meters.

It is necessary to pay attention to the position of the hand crank, determine the position before installing the drying rack, it looks unsatisfactory, and the blockage does not matter. Generally, it does not affect the entry and exit of personnel; not close to the sink; Directly connect two dual-mode trouser wheels, and the top bracket can be easily installed. The installation height of the hand crank should be about 100cm from the ground, and the corner is installed and installed, and the ceiling crank cannot be installed directly above the hand crank or the ceiling is directly above the hand corner, and the ceiling is only installed on the wall.

There are many types of drying racks. Different types of drying racks are suitable for different home environments. Among them, the wall drying rack is very special.

A lot of people don't know about it, so the introduction is here for everyone. Introduce some advantages and installation of wall drying racks for everyone to understand.

Yes foldable is possible. Folding it when you're not using it saves you some space. Stainless steel.

The material is usually made of stainless steel and does not rust from long-term watering. Flexible installation positions. The general position is relatively low, it is easy to hang clothes, and the space is large enough to hang a lot of clothes.

Drying rack fixing wall has been solvedAnd the drying rack installation step 1: understand the composition of the wall telescopic drying rack and its respective functions. Then install the accessories, and the top seat, as the name suggests, is mounted on the wall.

When installing the lifting frame, care should be taken to install it on a strong roof and at right angles to the wall. Corners are usually installed near the corners of walls.

Drying rack fixing wall has been solvedAnd the second step of drying rack installation: the installation position of the hand crank knife must be moderate, which can basically meet the needs of people at different heights. In addition, the hand-crank device is the force and force part of the garment, so it is usually installed on a wall without tiles, because it is easy to make if it is installed on a tile wall.

Install tiles by drilling holes. The drying rack fixed wall has been solved and the drying rack installation step three: Similarly, the length of the drying rod can be determined according to the size of its installation position.

If the drying stick is too long, it can be cut. If it's too short, it may require two rods in parallel. The distance between the drying rods usually depends on the size of their location or the owner's preference.

Drying rack fixing wall has been solvedAnd Drying Rack Installation Step 4: Finally, after you have made sure that all wall-mounted retractable racks have been installed, check that they are in place. Let the hand crank work to see if the lifting action is normal and smooth.

Check to see if the drying rod, wire rope and ceiling are balanced.

This drying rack is suitable for a lot of families, and it is very easy to install.

You can get it for free

The hanger will be deformed after a long time, and we can break it back to its original shape by artificial means; If it still can't be broken, I recommend that you fix it with a soft wire, so that the hanger can be turned back to the original. However, there are some wires that are not suitable for hanging hangers because it will rust, so it is better to have aluminum wires

In order to avoid the hanger from deforming after a long time, I would like to give you a few suggestions.

When drying clothes, wring them out as much as possible and then use a hanger to dry.

Some clothes must be washed by hand, and can not be washed by machine, so when washing by hand, it is difficult for people to wring out the clothes, often at this time, many people will wring the clothes to dry, which inadvertently increases the burden of the hanger, so it is easy to cause the hanger to deform.

If the hanger is not suitable for the item, do not use the hanger for drying.

Nowadays, many people will hang the quilt on a hanger when they are drying, in fact, this is not right, we should use a bracket to prop up the quilt, not use a hanger that exceeds its weight load to dry.

The hanger will be deformed after drying for a long time, you can choose to manually break it back to the original method, this method is very easy to solve, of course, if you are afraid of breaking the clothes rack with excessive force, then you can choose hot water to slightly blanch to restore the original shape.

Do a good job of stretching at the four corners of the hanger to avoid the hanger being crooked, and you must not underestimate the deformation of the hanger, which is a hidden danger over time.