How to improve the output of the milling system, how to improve the output of milling

Strictly implement the provisions on explosion-proof powder making system in the "Electrical Safety Work Regulations (Thermal and Mechanical Parts)".

Before starting and after the milling system is stopped, steam fire fighting and cold air blowing should be carried out in accordance with the provisions of the regulations.

Regularly check the amount of slag in the slag discharge box and discharge the slag in time; In normal operation, when the amount of slag in the slag discharge box is small, the slag should also be discharged regularly to prevent spontaneous combustion of the slag box.

The coal mill should be switched regularly to prevent spontaneous combustion of the raw coal bunker or the coal mill due to long-term shutdown.

Before stopping the furnace, try to empty the raw coal bunker or keep the coal level low to prevent spontaneous combustion of the raw coal bunker due to long-term shutdown.

During the normal operation of the coal mill, its steam fire protection system is in a good standby state to ensure that it can be put into operation at any time.

In the normal operation of the coal mill, it is necessary to strengthen the monitoring of the outlet temperature of the coal mill, and the outlet temperature control adopts an automatic adjustment method to ensure that the outlet temperature of the coal mill is less than 90.

The fire-fighting facilities near the coal mill are complete, and the regular test is qualified, and the operation duty personnel must know how to extinguish the fire.

Strengthen the management of coal combustion to prevent explosive materials such as detonators from being mixed into coal.

When a fire is found in the standby coal mill, all its entrance and exit damper baffles should be closed immediately to isolate the air, and the fire should be extinguished with steam firefighting.

When stopping the grinding, it is necessary to stop first to minimize the grinding force, then stop the coal feeder first, and then stop the coal mill after 15 seconds to prevent spontaneous combustion of coal accumulation in the coal mill.

I'm like this! When I was in school! No recipes!

There's no time to exercise! Because it's the third year of high school! I went from 140 to 110 in less than 3 months, and that's how many people lose weight!

In less than a month, if you stick to it, you can lose about 10 pounds in 20 days! Be sure to eat well in the morning! You can also have a full lunch but it is recommended not to be too oily!

But don't eat at night! If you don't get used to it at first, you can eat fruit or something at night! But not much!

Note! Don't eat snacks! No snacks!

Don't even hold on to eating at night! Don't think it's okay for a day! You can try it first!

It will be effective in a week! A friend of mine used to be over 130 and is now 110! I can have dinner after I get it down!

You can also snack less! But there are not many dinners and snacks, pay attention to KFC boiled fish, hot pot, don't eat such a high calorie, it doesn't matter if you don't eat dinner, right? You can eat kiwi, apple, tomato!

Not only can it be good, but it is also good for your health.

Morning Exercise After waking up in the morning, do about 20 minutes of freehand exercises, which can not only lift your spirits to meet the challenges of the day, but also maintain your youthful body. Ascending stairs Up and down stairs three to four times a week for 30 minutes each time burns about 400 calories and strengthens the calf, thigh and femoral muscles. Run in place Choose an open space of about one square meter indoors or in the aisle, and run barefoot for 15 minutes a day.

Walking Walking about 45 minutes after eating, walking at a speed of kilometers per hour will cause rapid caloric consumption, and it is better if you walk again 2-3 hours after eating. Skipping rope As long as there is enough space, skipping rope can be carried out anytime and anywhere, and can be integrated into the game. Salt therapy Rinse the whole body with warm water, then apply coarse salt to the whole body, and then massage it to make ** hot until it appears red.

Generally, it is massaged for 5-8 minutes and then immersed in 38 warm water for 20 minutes. Drinking water Among the many ** methods, drinking water correctly is the easiest and no burden. The water you drink here refers to boiled and mineral water, not high-calorie beverages, otherwise it would be counterproductive.

Drink at least 2 litres of water a day, one glass each after waking up, at breakfast, in the morning, before lunch, after lunch, before dinner, and after dinner, preferably slowly.

Exercise is a great way to do it. Obese people increase physical exercise, not only to increase the "expenditure" of body fat, so that the purpose of body shape recovery, but also to make the body organs to be exercised, enhance the physique. Therefore, increasing exercise is a very suitable and good way to do it.

I hope to be been.

First, starting from the raw grain, the raw grain is the basic condition for the improvement of milling yield. 2. Stabilize the production process and bring the performance of the mill, powder purifier and other systems to the best state. Of course, to improve the milling yield should be carried out under the condition of stable quality.

It is of great significance to improve the efficiency of grinding technology in grinding operation to improve the beneficiation index. So how can we improve the efficiency of grinding technology? In order to improve its production efficiency, it can be considered from the following aspects:

1. Adopt closed-circuit grinding process.

A reasonable grinding process should grind to a particle, and once it leaves the grinder, it should be immediately separated from discharge. On the one hand, to avoid excessive wear on the other hand, the grinding medium such as steel balls is completely coarse in mineral particles, so that the energy can do the work as beneficial as possible. Existing grinders perform particle size grading and are very difficult, which uses a classifier plant or a fine sieve to separate the size of the mineral particles from a qualified, coarse grinder, and then return them to the mill (also called back sand).

In the closed grinding circuit, the coarse many times failed to be effective until it was discharged by the machine mill. The second is to close the grinding circuit, because a lot of grit enters, so that the coarse grinder rises to the level of the compound. Grinding according to the principle of kinetics.

Then, the maximum energy is useful for the work, so the faster the grinding, the milling machine is more productive. In addition, the presence of sufficient sand back can eliminate fluctuations in the ore scale of the product produced by a new grinder. It is shown that closed-circuit grinding can effectively avoid the phenomenon of "coarseness".

It enables grinding on the premise of ensuring that the qualified, scaled, and obtained uniform, coarse, and reduced high-grade products, which is the next step in the sequencing operation is beneficial.

Second, use different mills.

Micro powder practitioners can choose different mills according to the different fineness of the ore to be grinded, for example, the ordinary Raymond mill below 400 mesh can meet the requirements, if the requirements for fine powder are too high, to achieve 1000 mesh or even higher fineness, ultra-fine grinding should be selected, and should not choose a mill that can barely meet the requirements.

Shanghai Kelirick machine **** for you to answer.

If you still have any questions, you can visit our official website and our technicians will answer them for you.

This mainly depends on what kind of fineness powder you need to make, our company has now studied and withstood a European version of the coarse grinding, the fineness is about 0-3mm, if the fineness can meet your requirements, you don't have to consider the output at all, it will only be more than you think. If you need a very fine powder, you may wish to visit our **Visit below, our company's customer service and technical staff will be happy to answer for you. By the way, our company is called Shanghai Dingbo.

The cutterhead should be good, and look at your material, what material is suitable for what mill, and the motor can also produce a high point.