How to deal with water leakage at water pipe joints?

Water seeps into the joints of the water pipes at home, although it is a very slight leakage, when it is always unsafe, what should I do? The first part is to check it to determine where the water is leaking If it is an iron pipe, you have to turn off the valve and remove the joint Plug one end with the palm of your hand Eyes from the other end Can you see a bright light Very small If there is, it means that there is a problem with the joint Or look directly at the appearance It may be that when you are on it, there is a problem with the quality of the joint It is cracked on the top, so that you may see cracks on the outside If it is a PPR pipe or an aluminum-plastic pipe, is it direct or an inner wire bend, if it is direct, it is better to cut it off and do it again (if you are not a professional, it is better to find a professional) There is a quality problem with the PPR inner wire joint, because the middle is iron, and the surrounding is plastic, sometimes it will be too tight, and it will be broken. I'm glad to answer for you, and I hope it can help you.

After looking at your picture, it should be that when the height of the water pipe is a little bit high, and then which elbow is installed, the teeth are a little oblique, so the screwing up is not done well or the seal is not done at all, so the water pipe is under pressure and seeps water.

1. If the water pipe joint at home is leaking, first disconnect the water source and unscrew the interface.

2. If there is a leak at the wire mouth, it can be removed, and if the leakage is not large, you can buy a group of agricultural machinery glue to mix and make up for it. If it is a metal joint, either tighten it, or remove it directly and add some raw material tape and tighten it from the head. If it is aging or leaking water in the glue or welding joint, it is more difficult, and it is best to replace it with a new one.

What to do if water seeps into the water pipe joint. If there is water seepage in the water pipe joints, see if the joints are not tightly closed, you can close them tightly in time to see if the situation can be improved. How to deal with leaking water pipe joints.

If the water leakage problem is serious, you must be able to find a professional plumber to repair it in time.

First use a hacksaw to see off the leaking place, the saw edge should be flat, and then use sandpaper to polish the leaking port and wipe it clean with a cloth. Then apply the glue to the port, wait 2 to 5 minutes, and then apply glue to the "bamboo" joint of the water pipe, connect the port to it, and rotate it repeatedly until it is firm. Finally, the other ends are joined together in the same way, and the appropriate amount of glue is applied to the seams.

1. How to repair the leakage of the water pipe.

1. First use a hacksaw to see off the leaking place, the saw mouth should be flat, and then use sandpaper to polish the leaking port and wipe it clean with a cloth.

2. Then apply the glue to the port, wait for 2 to 5 minutes, and then apply glue to the "bamboo" joint of the water pipe, connect the port to it, and rotate repeatedly until it is firm.

3. Finally, the other ends are also connected together in the same way, and then an appropriate amount of glue can be applied to the seam of the joint.

2. Causes of water pipe leakage.

1. The uneven settlement of the pipeline on the ground, the soil foundation and the settlement of the house foundation caused the pipe body to be subjected to additional stress, resulting in loose joint leakage, local cracking and leakage of the pipe body and overall fracture and leakage of the pipeline by shearing.

2. The buried pipeline is seriously corroded, and the pipe wall is thinned and leaks.

3. Due to the construction quality reasons, during the acceptance of the project, the acceptance was not carried out in strict accordance with the relevant specifications, and the quality problems left behind left a hidden danger for water leakage in the future.

3. Precautions for water pipe leakage.

When the water pipe is leaking, you need to turn off the power supply first, and before checking the cause of the water leakage, check whether the power supply is turned off, because water conducts electricity and is prone to danger. Then wrap the leaking place with a soft grinding item such as a rag to prevent the water from splashing around. Finding the valve of the water pipe, Chi Huai Dou tightened it until the water no longer flowed.

If you can't handle it yourself, you should find a repairman to repair the water pipes.

One is that it is not installed properly and reinstalled, and the other is that it is damaged and replaced with a new one.

What should I do if the water pipe joint is leaking? First of all, we need to understand the cause of water leakage, whether it is glue sent away, poor welding or joint corrosion that causes water leakage, and we need to solve it according to the specific cause. Here are a few of the causes of water leaks that I analyzed and how to fix them.

1. Remedial measures for water pipe leakage.

1.Cut off leaky pipes.

This is the easiest way to deal with water pipe leakage, cut off and reinstall, this method is actually not difficult, as long as you do not put the pipe into the wall should be able to implement, and the most thorough, because the advantage of PP-R pipe is that the welding strength is higher than the local, to ensure the overall tightness of the pipeline.

2.Glue. Generally speaking, glue is more suitable for pipelines with relatively low pressure, and the operating pressure cannot exceed 4 kg, which is not suitable for PP-R products, because PP-R material determines that glue is generally difficult to dissolve.

3.Welding. If the water pipe is thick, you can use a fuser to weld directly to the outside to plug the gap, and this method should not have too high pressure.

4.Welding torch. Using a welding gun, the solder is sprayed directly into the weld opening, which can be used using a PP-R repair rod.

2. Remedies for water leakage in water pipe joints.

1.If the water pipe joint at home is leaking, the first thing to do is to disconnect the water source and unscrew the interface.

2.If the water leakage at the wire mouth can be removed, if the leakage is not big, you can buy a group of agricultural machinery glue mixed to make up for it. If it is a metal joint, either tighten it, or directly remove it and add some raw material belt and then re-tighten it.

If it is aging or leaking water at the glue or welding joint, it is more difficult, and the best solution is to replace it with a new one.

1.Confirm the cause of the water leak.

If there is a water leak at the water pipe connection, the first thing you need to do is to confirm the cause of the leak. Usually, the cause of water leakage may be aging water pipes or loose connections, or it can be improper installation, etc.

2.Cut off the water source.

Once the cause of the leak is confirmed, the water source needs to be cut off immediately to prevent the leak from getting worse. The method of shutting down the water source depends on the specific situation. If it is a stand-alone water meter, the water source can be cut off by closing the valve next to the water meter; If there is a public water meter, you need to call the property or water supply company**, and Bohe will ask the relevant personnel to come and cut off the water source.

3.Dry the water pipes with a clean cloth.

Before carrying out repair and replacement work, the water pipe needs to be dried with a clean silver oak cloth to avoid water droplets affecting the fit of the joint. After wiping, you can use a lighter or hair dryer to dry the connections and the surface of the water pipe.

4.Replace the sealant pad.

If the cause of the leakage is the aging of the gasket, then the gasket needs to be replaced with a new one. Select the appropriate model and size of sealant gasket and place it at the joint. If the metal nut is loose, you can use a wrench to tighten the nut.

5.Replace the connectors.

If the cause of the water leak is aging or damaged connections, then they need to be replaced with new ones. According to the material and model of the connector, select the appropriate connector and install it in the leakage. Special attention should be paid to the size and direction during the installation process to avoid secondary disasters.

6.Install new water pipes.

If the cause of the leakage is the aging of the water pipe, then it needs to be replaced with a new one. In the process of installing new water pipes, it is necessary to take scientific and reasonable methods to ensure the coordination of water pipes and connectors. After installation, a certain period of water pressure testing is required to ensure the quality and effectiveness of the new water pipes.

7.Clean and maintain the equipment.

After the water leakage problem is solved, the equipment needs to be cleaned and maintained to extend the life of the equipment. Regularly check the use of water pipes and connectors, and replace aging parts in time, which can effectively avoid water leakage caused by aging.

8.Take care to prevent water leakage.

If you want to better avoid water leakage, you need to pay attention to the maintenance of the equipment and how to use it daily. It is necessary to regularly check the use of water pipes and connections, avoid using excessive water pressure, and pay attention to saving water when using water, so as to avoid pressure problems caused by excessive water use in households.

When encountering a water leakage problem at the water pipe interface, it is necessary to quickly arrange for a professional to deal with it. At the same time, it is also very important to prevent the occurrence of water leakage problems, and it is necessary to regularly check the equipment and daily use habits to ensure the long-term use of the equipment.