How do I use a GUNPLA sticker? How do you distinguish between adhesive stickers and scratch stickers

All water stickers are one big one. My suggestion is that where you want to stick, cut it out and soak it in water. Soon, the sticker will separate from the cardboard.

Carefully move them with tweezers to where they want to be attached, and then wipe off the surface with a cotton swab. It is best to apply another layer of water stickers with county water sticker softener, and then roll it flat with a cotton swab, so that the water stickers are not easy to fall off. Water stickers are divided into restickers and stickers.

The sticker is the kind with oiled paper at the bottom, which is used to make transparent glue. The transfer sticker needs to be cut separately and thrown on the surface of the model, scraped with a ruler or other hard object, and then the sticker will stick to the surface of the model.

The water stickers are a large sheet, my suggestion is that where you want to paste, just cut off what place to soak in the water, soon the water stickers will be separated from the cardboard, carefully move to the position you want to paste with tweezers, and then use cotton swabs to dip off the water on the surface of the water, it is best to use the water sticker softener to coat a layer on the surface of the water sticker, and then use a cotton swab to roll the water sticker flat, so that the water sticker is not easy to fall.

Soak it in water for a while and then move it to the model, just like the military model and civilian model. However, if you want to use water stickers, basically water sticker softeners and protective paints are necessary. If you are in the vegetarian group, it is not recommended to use a water sticker.

You can use a cotton swab dipped in water to apply it to the back (only for small water stickers), and then use tweezers or a pen knife to take it down, it is best to smear some water where you want to put it, so that it is convenient to move the sticker, and then the cotton swab can absorb the water dry, and it is recommended to use a softener.

Cut out the water sticker.

Soak in water for about 10 to 20 seconds.

Wait for the water sticker backing to darken.

Stick it to the model and use a cotton swab to slowly move the water sticker from the backing paper to the designated position.

Then use a cotton swab to absorb the excess water.

Then put it in a dry place to dry and it's OK.

Come on Wuhan, come on China This water sticker has: Bandai, Dalin, Snow Flame, Evo, Desen Pyro is not recommended: Bandai novice recommendation: Darin Forest, Snow Flame Senior Recommendation: Evo, Dessen Pyler.

The surface of the adhesive is smooth and the pattern has been cut. The water film can feel that the pattern is convex on it, the pattern needs to be cut off by yourself, and the bottom is paper, the scrape looks matte, there is a slightly sticky side to the touch, and there is a frosted paper to protect the scratch.

In fact, the Bandai model will only send stickers and scratch stickers, and not all models have scratch stickers, and water stickers are to be purchased separately.

Looking at the material, the front and back of the adhesive paste are generally smooth cardboard.

The texture of the water patch is soft.

There are obvious protrusions on the back of the scratch sticker.

By the way, if you just play Gundam, the water sticker is not very suitable, and the scratch sticker and adhesive sticker are good choices!

Here's how:

Lazy Law:

Use a pen knife or scissors to get it down and print it on the position of the model to be pasted (pay attention to the surface of the model to keep it clean), and then scrape it on it with your hands or other hard objects, pay attention to the uniform force on the sticker, and then slowly tear it off (pay attention to whether the patterns in the sticker are printed on the model, otherwise the sticker will be ugly if it is broken);

Fine Method:

Use a cotton swab dipped in a small amount of water (a light touch) to apply it to the sticker, and then fix the sticker with scotch tape (if you think the tape will leave marks, you can prepare erasers and brushes) on the model (also to keep the surface of the model smooth) also scrape with a fingernail or hard object, and finally tear off the tape.

Precautions: 1. Once the water sticker is coated with the softener, be careful not to touch or move the water sticker, otherwise the water sticker may be destroyed. When the water sticker looks wrinkled, it means that the sticker softener has worked, but it will shrink and flatten out when it dries.

2. The model water sticker should first cut the required part from the whole paper and soak it in warm water for about 1 minute.

3. Avoid using it in places that directly encounter open flames or high temperatures.

4. After a long period of use, it will cause discoloration or corrosion due to salt or acidity, please wipe it frequently.

5. Wipe the dirty place with a sponge dipped in water with neutral detergent.

6. Before pasting, please wipe the dust, oil, and moisture of the paste. Due to the material of the wall, it may not be possible to attach it to the wall. It cannot be used when the surface of the wall is rough and uneven.

Hello! Scratch stickers, also known as transfer stickers, are a bit similar to previous tattoo stickers! Transfer paste, there are several kinds of sticking (1) lazy method:

Use a pen knife or scissors to get it down and print it on the position of the model to be pasted (pay attention to the surface of the model to keep it clean), and then scrape it with your hands or other hard objects, pay attention to the uniform force on the sticker, and then slowly tear it off (pay attention to whether the patterns in the sticker are printed on the model, otherwise the sticker will be ugly if it breaks. (2) Fine method: use a cotton swab dipped in a small amount of water (a light touch) to apply it to the sticker, and then fix the sticker with scotch tape (feel that the tape will leave marks, you can prepare erasers and brushes) on the model (also to keep the surface of the model smooth) is also scraped with a fingernail or hard object, and finally the tape can be torn off. ps：

To make a model, it is best to paste it first and then do it when pasting a scratch sticker, so as to avoid damage when the sticker is disassembled after the model is made, I hope the above will help you!!

This bar has a special question post, if you need to ask questions, please move.

Cut out the pattern you want, and then fix it in the place where you want to paste it with transparent glue, and finally keep scraping to print the pattern. . .

Let's go to GUNPLA, there is a group of lip-mold parties here, and although I also assemble models, they are usually prime.

1. Different properties: water stickers are stickers that can only be used after water immersion. Stickers belong to the adhesive type of adhesive paper, which is printed on various pictures and photos on adhesive paper.

2. Different characteristics: water sticker is a new transfer technology that separates the pattern from the bottom paper and then transfers it to the substrate with water as a carrier to realize indirect printing. Stickers can be applied arbitrarily, and most of them are disposable. There are many varieties.

3. Different uses: stickers can be pasted on stationery, cups and bowls, furniture, electrical appliances, metalware, porcelain, motor vehicles or non-motor vehicles, etc. Water stickers can be applied to living room supplies: sofas, coffee tables, kitchen cabinets, chandeliers, ashtrays, vase decorations, containers, etc.

1. First use scissors to cut off the water sticker that needs to be used, as shown in the figure below

2. Then put the water sticker directly into the water and wait for about 40 seconds to 50 seconds, as shown in the figure below

3. At this time, the water paste is soaked and wet, and it becomes easy to separate from the carrier paper, and the water paste is transferred to the part to be pasted with a cotton swab, as shown in the following figure

4. After finally adjusting the position, use a dry cotton swab to stick the water around it and absorb it clean.

The basic way to apply stickers is Gundam water stickers.

Watermark = Watermark, also known as Watermark ......Soak the sticker in water, take it out after ten seconds, and use a cotton swab to drag the upper layer of the sticker pattern onto the model.

1 Clean the parts that need to be attached with water stickers (dish soap).

2 Soak the stickers in clean water.

3 When the water sticker pattern floats slightly, take it out with tweezers together with the bottom paper (be careful not to let the tweezers damage the pattern, and you can use round-tweezers if possible).

4 Place the water sticker (along with the liner paper) where it is needed.

5 Gently press and hold the water patch with a cotton swab (hold the water patch in place, but don't press it to death) and use tweezers to pull out the bottom paper.

6 Use a cotton swab to stick the residual water and blot it dry, and you're done, I hope it helps!

1. Tiangong white cover glue, seamless damage, time-consuming but significant effect, the melting of the model is relatively strong when using the regret dust;

2. Tiangong white cover glue, the usage is to group the model county fake, leave a small gap in the middle, and then apply it in the gap, the speed of the dry book sail is faster, and the melting of the model is also weaker;

3. Tiangong yellow cover glue is a special glue customized for ABS plastics, which will not melt the model, and the speed of Bizen drying is also very fast, but it will only play its maximum effect when it is for ABS series plastics.