How to clean the adhesive strip in the refrigerator so that you are not afraid of hiding bacteria?

I don't know if you will notice the sealing strip of the refrigerator when you usually clean the refrigerator, maybe most friends think that cleaning the refrigerator is actually to clean the place where the refrigerator puts food, the main thing is to wipe off water stains and then defrost and remove ice cubes.

In fact, the cleaning of the sealing strip is also very important, the design of this sealing strip is to make the refrigerator door and the refrigerator better fit, that is, to make the refrigerator more sealed, not only the heat from the outside world can not enter, but also so that the cold air in the refrigerator will not be released.

But after use, this sealing strip is easy to become dirty, for example, this usual food crumbs, and then the soup of the food is easy to drip on it, because of the moisture, there may be mold here, and some dust will accumulate on it. Because the sealing strip is a bit of a layer-by-layer design, between this layer and layer, it is easy to fall some impurities and dust, which may not be obvious in appearance, but in the end it will still deform the sealing strip and affect the sealing effect, so the sealing strip also needs to be cleaned regularly.

When there is not a lot of dust on the sealing strip, in fact, there is no need to remove it for cleaning, because many friends will not install it after removing it, which will affect the effect, so if it is only a little dirty, everyone will prepare a basin of toothpaste water, then a thin rag, and then prepare a card. First soak this rag with toothpaste water, then wrap it in the card, insert the card into the gap between the sealing strips, and then wipe it back and forth along the gap of the sealing strip, so that even if it is a very narrow gap, you can wipe it with a rag.

In order to avoid the seal being too wet, of course, you need to wipe it again with a dry rag, at least not too obvious water droplets on it.

However, some seals may not be cleaned for too long, very dirty, and can not be scrubbed clean with cards and rags for a while, so it is recommended to remove the seals and then clean them.

You can soak it in warm water and detergent for a period of time, and then use your fingers to carefully clean each crevice, clean the hard dirt inside, and finally dry it before installing it back.

The most commonly used is to use toothpaste to clean, apply the toothpaste to the adhesive strip, let it stay for a while, and then gently wipe it with a soft cloth, it should be noted that it should not be pulled hard to cause the seal to deform, and finally wash it with water.

The refrigerator strip is easy to hide bacteria, but if you take it down and clean it, you are worried that it will not go back, which will affect the sealing of the refrigerator, so you can squeeze the toothpaste into the water, take a towel, soak the rag with toothpaste water, and then wipe the strip.

If it is not particularly dirty, you can use a card, and then wipe it with a thin cloth outside the card, so that it can be wiped more in place, of course, if it is particularly dirty, you can remove it and put it in water with dish soap for cleaning.

You need to prepare: small bowls, paper towels, baking soda, white vinegar, chopsticks.

<>3. Open another bottle of white vinegar and pour it into the above small bowl, as shown in the figure below.

4. Then stir the liquid in the small bowl evenly, as shown in the figure below.

<>6. Next, wipe the mold spots on the refrigerator adhesive strip with a soaked paper towel, as shown in the figure below.

7. Finally, the mold spots on the rubber strip of the refrigerator will be removed, as shown in the figure below.

The refrigerator adhesive strip has been used for a long time, and there is a lot of mold on it, so teach you a trick to remove it easily.

The door seal is dirty and can be removed for cleaning:

Look carefully to see if the door seal is built-in, and today's refrigerators are generally built-in, which is convenient for disassembly, washing and replacement.

First, use a pen to mark the inside of the corner of the door seal to indicate the location. Then the upper two corners are slowly pulled out, the action should be light, and the door strip should be pulled down slowly.

When pulling to the bottom two corners, pull the two corners out first, and be careful not to pull the door seal.

Remove the door seal, soak it in warm water and detergent, and gently scrub the mold stains in the door seal with a soft-bristled brush dipped in dish soap.

Dry with a soft cloth and let dry. Then scrub the refrigerator door seal clean.

After the door seal is dry, attach it in reverse in the order in which it was removed. Be careful to press the corner in first, and press the door seal completely against the groove on the inside of the door.

There are also old-fashioned refrigerator door seals, which are fixed with screws, which is simpler, and can be removed slowly as usual, cleaned and then installed.

Is the refrigerator strip moldy and difficult to clean? A small way to easily remove mildew spots and clean them thoroughly.

Use a toothbrush dipped in dish soap and brush back and forth, then wipe it clean with a cloth.

Hello, you can use a cleaning ball and some dish soap for this, which is very clean.

Scrubbing with a hot towel will do.

The 、、、 can be removed by poking the shredded pot

The adhesive strip of the refrigerator is an important part of the sealing work of the refrigerator, but because the cavity is exposed to more air, it will inevitably absorb dust and greasy, which will affect its sealing effect, so it is very important to clean the adhesive strip regularly. The following empty spring is the method of cleaning the bucket round washable rubber strip:

1.Wash with soapy water: You can choose ordinary soap, add some soap to the water, wipe the adhesive strip with soapy water with a sponge, and then rinse it with water.

It should be noted that the adhesive strip must be left in it for a while before cleaning, so as to better soften the stain and stick to the adhesive strip.

2.White vinegar cleaning: Mix white vinegar with water in a 1:1 ratio, and then use a sponge or damp rag dipped in the mixture to clean the refrigerator adhesive strips. Wait a while, wring out the dry towel and dry it on the refrigerator adhesive strip.

3.Aluminum foil cleaning: Aluminum foil can not only be used in food, but also for cleaning refrigerator adhesive strips. Combine the aluminum foil into a ball, moisten it slightly and gently wipe the surface of the strip to clean it.

4.Breadcrumb cleaning: Cut a slice of bread from the bread and spread it on the refrigerator strip to wipe or rub the surface of the strip with bread, the bread scraps can saturate the oil and stains on the strip to achieve the purpose of cleaning.

In general, it is very important to keep the refrigerator strip clean, which can not only ensure the sealing effect of the refrigerator and prolong the life of the refrigerator, but also prevent the food from being contaminated due to the growth of bacteria, which can cause us health problems.

When the refrigerator adhesive strip is moldy and cannot be washed off, you can mix vinegar and dish soap with water, and then use a clean rag to put it in it to wet it and wipe the moldy adhesive strip back and forth. You can also apply toothpaste to the moldy part of the adhesive strip, and then wipe the moldy adhesive strip back and forth with a clean rag, and the mold on it will slowly disappear.

If the refrigerator adhesive strip is moldy and cannot be washed off, it can be treated with vinegar. First of all, you need to cut off the power of the refrigerator, wipe the moldy part of the refrigerator rubber strip with a rag, mix it with vinegar and dish soap, and then wipe the moldy rubber strip back and forth with a clean rag, and the mildew on it will slowly disappear.

Apply the toothpaste to the moldy area of the refrigerator strip, and then wipe the moldy spot with a clean wet rag with a clean wet rag, you need to be careful not to use too much force to avoid pulling the strip to cause the strip to deform and affect the sealing. After wiping a few times, wash it with clean water can significantly improve the moldy condition of the rubber strip.

If there is mold in the gap of the rubber strip, you can pour an appropriate amount of alcohol into the bowl, wrap the paper towel with a fork, and then use the paper towel on the fork to dip the alcohol and press back and forth along the gap of the rubber strip, you can clearly see that the paper towel will gradually turn black, and the stolen goods on the paper towel are the mold and dirt in the gap of the rubber strip.

Many people will have the problem that the refrigerator strip is moldy and can't be washed off, so what should I do if the refrigerator strip can't be washed off if the mold strip can't be washed? Next, I will introduce some methods for you.

The reason why the refrigerator adhesive strip is moldy is mostly because of the smell of food in the refrigerator, coupled with the fact that there is always stagnant water in the refrigerator, which leads to the increase of bacteria, and the refrigerator door is closed, the natural adhesive strip is easy to breed bacteria.

1. Vinegar can also be used to clean off the mold of the refrigerator sealing strip, and the ingredients in the vinegar and mildew will have a chemical reaction. Vinegar not only has this effect, but also kills bacteria on the refrigerator seal.

2. You can use an old toothbrush to dip in dish soap to remove the mildew of the refrigerator strip, so that the cleaning effect is more thorough.

3. Add an appropriate amount of baking soda to the water. Wet the rag in baking soda, wring out the excess water, and wipe the moldy area of the refrigerator strip.

If you can't handle it yourself, get a professional to have it inspected and repaired to avoid more damage.

Here's how:

1. Clean with toothpaste. Start by squeezing the toothpaste, apply it to the moldy area of the strip, wait a few minutes, and wipe it with a damp towel or paper. Rinse with tap water.

2. Clean with alkaline-containing substances. We can clean it with alkaline substances, similar to alkaline noodles. Pour a spoonful of alkaline noodles on top of the moldy strips, and after a while, pour some tap water and wipe it.

3. Wash with alcohol. Use chopsticks dipped in alcohol to wipe back and forth on the moldy part of the rubber strip of the refrigerator, and then wipe it evenly with a paper towel, we can see that it is stained with stains. Then wash with clean water and you're done.

4. Wash with vinegar. We all know that vinegar is an acidic substance, and it can be reacted with moldy substances, rubbed back and forth on the moldy area with a cloth dipped in vinegar, and finally washed with water.

5. Laundry detergent cleaning. We know that household laundry detergent can remove stains, so after washing the clothes, we can use laundry detergent to wipe the mold.

6. Detergent. Detergent is generally used to wash dishes, of course, it can play a role in sterilization and cleaning, which is also a quick way.

The method of cleaning the moldy strip of the refrigerator is as follows:

Tools Materials collapsing and stuffy: bowls, alcohol, refrigerator cleaner, rags.

1. The mold of the refrigerator sealing strip is due to the small food molecules and moisture in the refrigerator providing growth conditions for the mold, and the temperature at the rubber strip is higher than that in the refrigerator, so the rubber strip begins to grow mold.

2. Prepare a bowl and pour an appropriate amount of refrigerator descaler and water into the bowl, or only add medical alcohol or high white wine balls.

3. Use a rag to dip an appropriate amount of noisy refrigerator descaler or alcohol in a bowl, and wipe the mildew of the refrigerator rubber strip back and forth.

4. After wiping off the mold, you can remove the rubber strip and thoroughly clean all corners of the rubber strip with clean water to prevent residual dirt.

5. Finally, the cleaned refrigerator sealing strip can be put back into the refrigerator, and regular cleaning of the refrigerator sealing strip can ensure the hygiene in the refrigerator.

How do you clean a moldy refrigerator strip? After the refrigerator strip is moldy, it should be cleaned in time to ensure the cleanliness of the refrigerator. Next, I will introduce it to you.

Toothpaste

Apply the toothpaste to the moldy place in the refrigerator strip, wait for 2-3 minutes, find a toothbrush without it, dip it in water and gently brush off the mold with toothpaste, at this time the mold is very easy to brush off. Finally, wash it with water and wipe it with a dry rag.

Vinegar

Vinegar can be a good way to eliminate mildew, vinegar and water are diluted in a ratio of 1:5, then add dish soap, and then take a dry rag or an old toothbrush dipped in vinegar water to gently wipe the mildew of the rubber strip, and the mildew will be easily wiped off by us, which is very simple and practical.

Alcohol

Pour alcohol into an open bottle or bowl and wrap a paper towel around a fork, taking care to keep it firm. Then, a paper towel from a fork is placed into the container bridge to fill the mouth with alcohol, and the gap between the sealing strips is pressed and wiped repeatedly.

Tips:If you can't handle it yourself, get a professional to have it inspected and repaired to avoid more damage.