Does putty curing agent smell, and whether the putty has been dried fast or slow with the curing age

Putty is also known as unsaturated resinPuttyIt is made of unsaturated resinsTalc, styrene and other materials, the main ash made by stirring and grinding, is a two-component filling material, which has the advantages of fast curing and drying speed, strong adhesion and easy grinding.

Use a spatula to scrape the prepared putty on the sanded two-component base field paint or pre-treated board.

On the surface, if a thick layer is required, it is best to scrape it to the desired thickness in several thin layers. If air bubbles penetrate during scraping, they must be scraped thoroughly with a scraper to ensure good adhesion. Generally, the best wet grinding time is the hour after scraping (water grinding polishing, which can only be sprayed after the water vapor is dry).

2 to 3 hours is the best dry grinding time. After grinding quietly, remove the surface dust, and then spray the middle paint, top coat, overprint varnish, etc. For example, for high-demand occasions, after the putty is polished, it is necessary to scrape and apply fine scraping putty (red ash, eyefill ash) to fill in the small defects, and then spray the display layer and polish to check the fine defects, and then do follow-up spraying.

Summary. Putty belongs to water-based paints.

Putty belongs to water-based paints.

Putty is more delicate and has a stronger flavor. When using putty, the surface of the coated object should be washed and sanded before it can be used.

Advantages of solid ash: 1. High solid: there will be no problem of reflecting the thin consistency of gray body.

2. Scraping: The ash body is delicate, and the scraping is smoother than that of ordinary putty. 3. Less trachoma:

60% less than ordinary putty trachoma. 4. Grindability: Composite solid ash is very good for grinding.

5. High temperature resistance: solid ash can withstand high temperatures above 120 degrees. 6. Filling:

Because it is a high solid, the filling performance is better than that of ordinary putty. 7. Interface: firm, neat, better jointing effect.

8. The air dryness and adhesion are better than those of ordinary putty, and the flexibility has reached the standard required by the original ash, which is more suitable for large-area coating and scraping. 9. Cost-effective and efficient: Compared with ordinary putty ash, the actual use economy of high solid ash is almost the same, and because it is easy to paint and scrape, it can save more coating and scraping time, so that the construction efficiency is improved a lot.

Hello, putty can dry in 3-5 minutes. The surface drying time refers to the surface drying time of putty, and the drying time refers to the complete drying time of putty. The drying time of putty is different for different properties, some dry fast and some dry slowly.

Additional: The use of putty is generally dried for a few hours1, the ratio of base ash and curing agent is 100:2 to 5 (weight meter), the lower the temperature, the more curing agent is used.

2. The surface of the coated metal should be completely removed from oil, rust, old paint and water. 3. The dosage of putty should be used up at one time, and the base ash and curing agent should be prepared in proportion until the color is uniform and consistent.

Summary. Putty is a kind of polymer material, composed of two parts: the main ash (base ash) and the curing agent, the main body ash is mostly composed of unsaturated polyester resin and filler, and the composition of the curing agent is generally an initiator and a plasticizer, which plays a role in initiating polymerization and enhancing performance. Unsaturated polyester resin is the main body, which is polymerized after initiation, rapid prototyping and curing, and adheres to the surface of the object, and thinners such as styrene and other modified materials are often added to the filler to improve the overall performance.

This ability to adhere to the surface of a substance and quickly prototyping makes it particularly suitable for surface coating applications, such as automobiles, ships, furniture and other industries.

Hello, no matter what season you are in within 2 hours, as long as it is normal construction, you can do it within 2 hours.

Putty is a kind of polymer material, composed of two parts: the main ash (base ash) and the curing agent, the main body ash is mostly composed of unsaturated polyester resin and filler, and the composition of the curing agent is generally an initiator and a plasticizer, which plays a role in initiating polymerization and enhancing performance. Unsaturated polyester resin is the main body, which is polymerized after initiation, rapid prototyping and curing, and adheres to the surface of the object, and thinners such as styrene and other modified materials are often added to the filler to improve the overall performance. This ability to adhere to the surface of a substance and quickly prototyping makes it particularly suitable for surface coating applications, such as automobiles, ships, furniture and other industries.

Summary. Stir well before each use. Now the lower part is relatively dry.

Do not dilute with paint, add curing agent. It softens a lot when it heats up. It's no problem to use.

Pay more attention in the future. If it feels too dry. You can open a new can of blending and use it.

Add diluents such as styrene and other modified materials to dilute. However, it cannot be diluted with water or other organic solvents, which will affect the use effect of putty and will cause problems such as non-curing, non-drying of the surface, and reduced adhesion.

Dear, please wait.

Putty has more solidifier and less dry, is there any way.

Putty has more solidifier and less dry, is there any way.

How to solve it.

Pro, the putty curing agent will solidify if it is less, but it will be slower, and it will not dry if you don't wait for a long time.

Is there no way to fix it.

Dear, if it doesn't work, you have to scrape it and do it again, and the putty can't be dried without reinforcing the chemical agent; and no adhesion

Can you add anything else?

Stir well before each use. Now the lower part is relatively dry. Do not dilute with paint, add curing agent.

It can soften a lot when it heats up. It's no problem to use. Pay more attention in the future.

If it feels too dry. You can open a new can of noisy sedan car and use it. Add diluents such as styrene and other modified materials to dilute.

However, it cannot be diluted with water or other organic solvents, which will affect the use effect of putty and cause problems such as non-solidification, non-drying of the surface, and reduced adhesion.

The main differences between solid ash and putty are as follows:

1.Solid ash is a powdery substance, composed of carbon socks, oxygen, nitrogen and other elements, with high thermal stability; Putty is a liquid-like substance, composed of water, carbon, oxygen, nitrogen and other elements, and has low thermal stability.

2.The melting point of solid ash is higher than that of putty, and the melting point of solid ash is generally above 1000, while the melting point of putty is generally below 500.

3.The density of solid ash is higher than that of putty ash, and the density of solid ash is generally above, and the density of putty is generally below.

Summary. Putty curing agent mainly refers to chemicals containing silica (SiO2), which are used to pour liquid waste, etc., into sand and avoid liquid leakage when curing.

There is no curing agent for atomic paint, can it be done?

Putty curing agent mainly refers to chemicals containing silica (SiO2), which is used to pour liquid waste into the sand section, and avoid burning and avoiding liquid leakage during curing.

Alternatives depend on the nature of the liquid you need to cure, but here are some options that may help:

Putty curing agent mainly refers to chemicals containing silica, which are used to pour liquid feiwu into sand, which is resistant to air and avoids the leakage of liquid during curing.

1.Cement - Cement is a commonly used infusion material that absorbs liquids and becomes hard during the curing process.

2.Polymers - Different types of polymer grinding, such as acrylic resins or polyurethanes, can be used to pour liquids into a clump of hard material during the curing process.

3.Expanded Clay - When rounded with a chemical squeeze with a liquid mix, expanded clay can create a solid block of spring reeds and form a soft and flexible texture when cured.

It is important to note that chemicals should be handled with caution and that any hazardous or hazardous materials should be properly disposed of in accordance with the relevant regulations.

Hello: Under normal circumstances, if the atomic paint does not add a curing agent, it is difficult to harden and cure.

The hardener is a key component in atomic paints, helping to fill and liquefy the atomic paints, while providing additional resistance and stability to the final surface coating.

If you don't have an atomic paint hardener, you can try the following:

1.Lian Combustion is the leading businessman. Your Atom Paint** business may have a spare hardener to choose from. If you are unsure which hardener is right for your atomic paint, you should consult with a dealer for advice.

2.Use other types of finch-based curing agents. While the curing agent may vary depending on the brand, type, or composition, it is possible to try other types of hardener.

However, it is important to note that different types of hardeners may affect other properties of your atomic paint.

3.Mix according to the manufacturer's recommendations. If you use a specific brand or type of atomic paint, it is recommended that you mix or use a specific curing agent according to the manufacturer's recommendations to ensure the quality of the coating and the effect of the surface treatment.

Tips: It should be noted that the use of non-specified curing agents or their hypovoltaization may affect the appearance and stability of atomic paint, so please be careful and conduct appropriate testing and evaluation.

The work went well.