What should I do if the remote computer does not accept the connection when I connect to the Samba s

Sometimes you will encounter a situation where the remote computer or device will not accept the connection, just open the browser, click Settings, and Select"Internet Options", select"Connections", click"LAN settings"OK.

The remote computer or device will not accept the connection by following the steps below

1. Open the "Tools" menu on your browser, and then open the "Internet" option in the pop-up menu.

2. Open the Internet Options window and click the [Connection] tab.

3. Find and open the [LAN Settings] button in the interface.

4. Open the "Local Area Network (LAN) Settings" window, uncheck all the check boxes, and click "OK".

5. Open the browser's "Tools" menu again and select Don't use **Server.

Notes:

1. You can also open the desktop"Networking", select"Open the network sharing center"Fix an issue where a remote computer or device will not be connected.

2. Check whether the Remote Access Connection Manager service is enabled.

Here's how to fix it:

1.Click on Computer.

2.Right-click and select Properties.

3.Open Remote Settings.

4.Select Remote Operations.

5.Check the command that allows you to control this computer, and after checking it, click OK.

This is especially true after using software such as lantern, even if the software has already been uninstalled.

The symptom is that the Internet Explorer browser cannot access the Internet, if the site is set up locally, it cannot be accessed through http: localhost or access, while other browsers like Firefox and Chrome can be used normally. Detection via Windows Network Diagnostics indicates that the remote computer or device is not accepting the connection.

Solution: 1. Open the "Start" icon in the lower left corner of Win7 and find the "Control Panel".

After opening the control panel, the interface:

Then tap on the Network & Internet option.

2. Go to the "Internet Options" directory and set the connection to enter the LAN settings.

Only "Auto-detect settings" is checked, and all other options are unchecked.

Click "OK", "Apply". Complete the configuration restoration. Now you can enjoy browsing the web again.

The first one restarts the computer, if it doesn't work, proceed to the second step, reinstall the system, and the third step, buy a new one.

It's okay to use the computer doctor in Jinshan Ba Poison to fix it.,That's how I am.,It's slow to repair at first.,I'll wait for him to fix it himself later.。

Repaired with velvet for safe network disconnection.

The remote computer or device will not accept the connection, which is what's going on and can't get online.

I wonder if you fixed this issue?

844 Cheerful Words Or 1 Perkin Female Parking Fee Tea Restaurant at School Uh Uh How much wind $

Install a 360 butler and fix the network.

Did you not turn off the VPN the last time you shut it down?

This is a connection problem, and it could also be a device problem.

I can't get on the network at the manual service point in the 360 security guard.,I can't get into the web page after I turned over the wall host and didn't change it back.。

In the security settings, lower the security level.

Can it solve your problem?

Win10 first uses Telnet IP 445 or Telnet computer name 445 to find that it is not connected, and it is useless to turn off the firewall, at this time the ultimate solution comes: run, select "Local Computer Policy" in "Local Group Policyr" Computer Configuration Windows Settings Security Settings IP Security Policy, on the local computer, then double-click "New IP Security Policy" on the right side, double-click "New IP Filter List", click "Filter Operation" tab, Double-click "New Filter Operation" and select "Permission", it means that port 445 is allowed, and you can open the shared folder.

If the 445 service port of the other party is not opened, check whether the firewall of the target machine is turned off and whether the file and print resource sharing service is enabled.

Whether there is a problem with the network, and whether the network between your computer and the printer is normal.

If there is an error in the permission configuration of samba, the testparm -s command can check this file for errors and, if so, display its line number.

The library is not supported, run the following command:

sudo apt-get install libtalloc2

Did the established user give permission?

Port 80 is always open. Otherwise, you won't be able to get online. Port 80 and port 445 are open by default, one is the HTTP protocol and the other is the UDP protocol, that is to say, one can browse the web, and one can log in to software such as QQ, which is why sometimes you can QQ, but you can't open the web page, the protocol used is not the same.

Port 80 is used to open web pages.

Modify the Cannot Access File Permission: Right-click to access the file ......Attribute (r) ......Safe ......Premium ......Owner system changes (c) ......Premium ......Find (n) ...... nowSearch result (u) click: The name I gave to the computer when I installed the system (that is, the one I dotted the little head at the bottom in blue) ......Determine ......Determine ......Replace the owner of the subcontainer and the object (preceded by a small square mark) ......Application (a) ......Yes (y) ......OK all the way.