How to paste wallpaper can be pasted well

There are a few things to keep in mind when sticking wallpaper:

The moisture content of the wall base should be less than 8%.

The flatness of the wall is checked with a 2 meter * ruler, and the height difference does not exceed 2 mm.

3.When stitching, the pattern is first and then stitched, so that the upper and lower patterns match.

4.It is forbidden to seam at the sunny corner, and the wallpaper should be wrapped more than 20 mm above the sunny corner.

5.When framing fiberglass wallcovering and non-woven wallcovering, the adhesive can not be brushed on the back, and the adhesive is brushed on the base layer by the figurine. Because the wallcovering has small pores, the adhesive will print through the surface and appear glue marks, which will affect the appearance.

Wallpaper, also known as wallpaper, is an interior decoration material used to paste walls, which is widely used in the interior decoration of residences, offices, guesthouses, hotels, etc. Materials are not limited to paper, but also include other materials.

Because it has a variety of colors, rich patterns, luxurious style, safety and environmental protection, convenient construction, suitable and other incomparable characteristics of other interior decoration materials, so it has been popularized to a considerable extent in developed countries and regions such as Europe, America and Japan.

Wallpaper is divided into many categories, such as laminated wallpaper, coated wallpaper, embossed wallpaper, etc. Base paper is usually produced from bleached chemical wood pulp, which is then processed in different processes, such as coating, printing, embossing or surface coating, and finally cut, packaged and shipped to the factory. It has a certain strength, toughness, beautiful appearance and good water resistance.

Clean the walls first, and then tile the wallpaper, and you can paste it well.

The specific method of sticking wallpaper in the room:

1. In the preparation of pasting, it is necessary to clean up the dust, dirt, etc. on the base or substrate, and there shall be no flying thorns, pittings, sand particles and cracks. The yin and yang angles should be straight. The base surface is alkaline.

2. There should be alkyd varnish to paint the closed base layer, which should be selected and classified according to the variety, pattern, color and specification of the wallpaper, cut the parquet, and put it flat for later use after numbering. When pasting, paste in numbered order.

3. For the purpose of attaching very firmly, it is necessary to work on the surface of the old solvent-based paint wall with a flat surface. When pasting, if there are less than one roll of seams, then a long time should be in the inconspicuous or darker part, there should be no seams at the sunny corner, and the seams at the yin corner should be lapped, and the corners should be compacted.

4. The method of adhesive wallpaper is to soak in water for a few minutes or so in construction, if it is the surface level, a layer of paint should be painted when pasting the wallpaper, and the paint color needs to be close to the wallpaper. The first wallpaper is very important, and it must be applied with a tool that pulls a vertical line.

5. The mounting of composite wallpaper can not be soaked in water, and the back of the wallpaper is coated with adhesive for about five minutes, and when the wallpaper is pasted, the surface of the base layer should also be coated with adhesive to achieve the effect of kneading.

1. How to paste wallpaper - check the quality of the wall.

Before pasting wallpaper, the wall must be kept clean and flat, and secondly, the water absorption and pH of the wall should be moderate. If the wall has been painted before, then it will take at least half a month to dry.

Second, how to paste wallpaper - do a good job of ground protection.

In order to keep the floor clean and tidy when laying the wallpaper, it is necessary to protect the floor. For example, a plastic film is applied to the floor, which not only prevents the glue from staining the floor, but also protects the floor.

3. How to paste wallpaper - measure the size.

Measure the dimensions of the wall to be wallpapered and calculate the amount of wallpaper.

Fourth, how to paste wallpaper - cut wallpaper.

When cutting wallpaper, the length of each cut should be larger than the length of the wall, usually 10 cm more. Secondly, the remaining part of the cropped wallpaper can be used for later repair, which can save the amount of use. If there is an extra beam in a large area of the wall, then you can do without wallpaper, so the effect will be better.

Fifth, how to paste wallpaper - the wallpaper glue softens.

After applying glue to the back of the wallpaper, fold it in half to soften for a while. However, when gluing, a protective tape should be pasted, so that the surface layer of the wallpaper will not be stained with glue when folded in half.

Sixth, how to paste wallpaper - wallpaper paving.

Some auxiliary tools can be applied when pasting wallpaper to make the paving effect more beautiful. Secondly, pay attention to the time when paving, if the time is too long, it will be dry, and it cannot be torn up for correction after paving.

7. How to paste wallpaper - wallpaper trimming and cleaning.

If it is an overlapping part, pay attention to the alignment of the patterns, and the overlapping parts should be divided. In addition, if there is a part of the wire switch panel, special attention must be paid to the paving, and the glue scraped on the panel should be wiped clean with a sponge immediately.

Through the above elaboration on how to paste wallpaper, I hope friends can learn some methods. Although the wallpaper is beautiful, it is necessary to pay attention to maintenance in ordinary use, and can not scrape the wallpaper with a pen or sharp things, which will not only reduce the aesthetics, but also shorten its service life.

Answer 1: Fill the hole in the wall with putty, and level the wall with a scraper. 2. Measure the size of the wall, and then measure the wallpaper based on the wall area, pay attention to the length of the wallpaper, more than the actual veneer, and then add water to the powder wallpaper glue and water to reconcile the general wallpaper with 1:3, and the foaming wallpaper with 1:3

2. Blend, or use the special glue for wallpaper that does not need to be blended, and the roller brush is stained with the blended wallpaper special glue evenly brushed on the back of the wallpaper. 4. Then put the wallpaper against the wall, and paste the wallpaper from top to bottom and from the corners to the inside with a wooden handle brush to level the wallpaper. 5. When encountering a power switch or socket, cover the wallpaper first and then brush it flat with a wooden handle, then use a utility knife to draw a cross diagonally on it, use a scraper against the edge of the switch, and use a utility knife to cut off the excess part.

6. If you encounter a connection by the printed wallpaper, find the consistent position of the pattern at the junction of the two wallpapers, overlap and paste about 12cm wide, and after the whole wallpaper is all aligned, use a scraper to resist, and then cut off the overlapping part with a blade. 7. Pay attention to pasting wallpaper from top to bottom, if you find uneven floating paste, you can use a towel to wet it, and then re-level it with a scraper. 8. Finally, the wallpaper around the door and window is processed in the same way as the wallpaper at the power switch.

9. After the wallpaper is pasted, the original device is installed.

Question: I bought the glue on the original paper, is it right for the gaps.

At present, there are many materials used in wall decoration on the market, such as coatings, integrated walls, etc., of which wallpaper is one of them, and the construction of wallpaper is relatively simple compared with coatings, as long as it is handled carefully in the construction process.

First of allTo inspect the wall, in addition to keeping the wall clean and flat, but also check the pH of the wall, if the wall has been painted before, then wait for it to dry naturally for more than 15 working days before the wallpaper can be pasted.

SecondlyIt is necessary to do a good job in ground protection, generally before the construction of wallpaper, a layer of plastic film should be laid on the ground, which can avoid falling glue from staining the floor and protect the ground well.

ThirdIt is necessary to measure the size of the wall, measure the wall surface of the wallpaper to be pasted, and calculate the amount of wallpaper, such as the width of the wallpaper to remove the protective edge is its shortest distance, and the height from the top of the wall to the baseboard is the shortest height of the wallpaper.

FourthIt is to cut the wallpaper, the height of each wallpaper should be larger than the actual size of the wall length during the operation, generally about ten centimeters, and then the remaining part of the cutting can be retained for later repair, if it is a complete wall in the middle of the more than a beam, then the beam can not be pasted with wallpaper, so that the effect will be better.

FifthIt is to soften the glue on the wallpaper, use a scraper to evenly coat the glue on the wallpaper, and then fold the wallpaper in half to let it soften for a period of time. In addition, when gluing, an orange protective tape should be laid so that the surface layer of the wallpaper can be folded in half to avoid the glue on the surface.

SixthIt is the wallpaper paste, when the wallpaper is pasted, you can use the instrument to keep it horizontal and vertical, but also to the upper and lower positions of the surplus, in the pasting action should be fast, otherwise the glue will dry up and will not be pasted, and the wallpaper that has been pasted can not be torn up and then pasted.

FinallyIt is the wallpaper trimming and cleaning, if it is a patterned wallpaper, then pay attention to whether the pattern is aligned when the pattern coincides, and also cut the overlapping part, in addition to the switch panel part must be straightened when pasting, so that the effect is good-looking, and the excess glue at the wallpaper splicing should be cleaned in time with a rag.

1: Songyu liquid wallpaper 2: Huafang liquid wallpaper 3:

Eastman Liquid Wallpaper 4: Martin Liquid Wallpaper 5: Yimijia Liquid Wallpaper 6:

Wan Lei Liquid Wallpaper 7: Thumb Liquid Wallpaper 8: Sigm Liquid Wallpaper 9:

Bimet Liquid Wallpaper 10: Aubang Liquid Wallpaper ??Remarks:

The above liquid wallpaper brand is currently a more formal operating brand on the market, and are production-oriented enterprises, of course, there may be a small list of production enterprises are not listed one by one, China's current liquid wallpaper industry companies have about 300 large and small, but less than 20 production-oriented enterprises, most of which are ** nature. ?This ranking is based on:

According to the company's establishment time, it is ranked in order, and if there is an error in the middle, it may not be large.

It is best to find a professional personnel sticker, you will stick it yourself, it will be bubbling, and the gap is not necessarily good, the glue is very important, and it should be environmentally friendly.

The first piece of wallpaper is very important, it should be vertical, the side seal should be neat, not high or low, and the bubbles should be scraped flat

1. If the wall is uneven, fill it with putty, measure the height of the wall, and cut the wallpaper according to the height. 2. Mix glue and water together, and use a roller brush to brush the glue on the back of the wallpaper. 3. Lean the wallpaper against the wall, from top to bottom, from the corners to the inside, and the wallpaper should be flat.

4. After pasting the first sheet, the second sheet and the first sheet overlap by 1-2cm, and the pattern should also be aligned. 5. Paste the wallpaper in the same way. ”

1. Soak the wallpaper and make it fully moist.

2. Polishing the wall surface to make it smooth, and the surface is clean and free of debris and foreign objects.

3. Brush the glue and paste it, and the glue should be evenly applied.

4. Paste the wallpaper, scrape it with a scraper while pasting, and drive out the air between the wallpaper and the wall. Make it fit snugly.

5. Then perform the action of scratching and scraping, and scrape each wallpaper.

6. Cut off the extra wallpaper in the corners.

7. Repeat the above actions until the entire wall is pasted, and the wallpaper should overlap with the wallpaper.

It's all about finding a professional master to post it. It's a bit more time-consuming to post it yourself. Look at the label in the wallpaper. I can see it from the inside, and then cut the wallpaper, glue, and wall after I know it!

Generally, it is better to find professional workers to do it, if you want to do it yourself, first cut off the wallpaper, apply the glue evenly, paste it from top to bottom, leave a few centimeters of margin on it, and you can do a good puzzle.