How to stick wallpaper to be firm, how to stick wallpaper to stick well

Wallpaper Steps:

Remove the wall skin: remove the original paint and other objects on the wall, use gypsum powder to supplement the cracked parts of the wall, and apply bandages after leveling; If it is a sand-gray wall or partition wall, it should be covered with glass silk cloth or really good cloth; Some poor quality partitions or exterior walls need to be nailed with gypsum board to achieve the insulation effect.

Cutting wallpaper: Measure the height of the wall first, and then cut the length of the wallpaper, there are two situations: do not cut the flower wallpaper according to the height of the wall about 5 to 8 cm in length, as a trimming up and down:

For flower wallpaper, the symmetry of the pattern needs to be considered, so the cutting length should be increased according to the actual situation, usually 8 to 10 cm longer.

Brush glue: the wallpaper glue is painted on the back of the cut wallpaper with a brush, pay special attention to the edges around must be coated with glue to ensure the quality of construction, the painted wallpaper, the glue is folded and placed for 5-10 minutes (note, no external force shall be applied, so as not to crease the wallpaper, especially the cloth) so that the glue can be posted after completely penetrating the bottom of the paper, and several wallpapers are painted each time, and posted in order.

Wallpaper construction: Generally the first wallpaper is posted on the side of the door or in the dark corner from top to bottom, with a scraper from top to bottom, from the inside to the outside, gently scrape the wallpaper, squeeze out bubbles and excess glue, so that the wallpaper is flat and close to the wall.

Before pasting wallpaper, turn off the power: When pasting wallpaper, if you encounter a place with a power switch or socket on the wall, you can turn off the total power supply first, and then cover all the power and sockets with the wallpaper, cut out two diagonals from the center of gravity, and four small triangles will be displayed, and then use a utility knife to remove the excess wallpaper around.

Trimming and cleaning: cut off the excess wallpaper at the upper and lower ends, the knife edge should be sharp to avoid burrs, and it is best to use a Japanese imported blade that sells a piece of yuan on the market when cutting some wall cloths. Then use a sponge dipped in water to completely wipe the glue remaining on the surface of the wallpaper to avoid the wallpaper from turning yellow, after the wallpaper is dry, if there are bubbles on the surface, cut it with a knife and inject the glue and then flatten it to eliminate it (it is better to use a syringe).

First brush a layer of 803 glue, we have a bucket of 60 yuan here, brush a house is almost, and then paste the wallpaper, feel not very relieved to brush a few more times of glue.

Listen to your description, your wall skin has no strength, it's better to shovel it, and finally make it into sandwich biscuits, it's not good, I really don't want to shovel, brush off the surface of the white ash.

Apply a layer of interface agent on it.

1. How to paste wallpaper - check the quality of the wall.

Before pasting wallpaper, the wall must be kept clean and flat, and secondly, the water absorption and pH of the wall should be moderate. If the wall has been painted before, then it will take at least half a month to dry.

Second, how to paste wallpaper - do a good job of ground protection.

In order to keep the floor clean and tidy when laying the wallpaper, it is necessary to protect the floor. For example, a plastic film is applied to the floor, which not only prevents the glue from staining the floor, but also protects the floor.

3. How to paste wallpaper - measure the size.

Measure the dimensions of the wall to be wallpapered and calculate the amount of wallpaper.

Fourth, how to paste wallpaper - cut wallpaper.

When cutting wallpaper, the length of each cut should be larger than the length of the wall, usually 10 cm more. Secondly, the remaining part of the cropped wallpaper can be used for later repair, which can save the amount of use. If there is an extra beam in a large area of the wall, then you can do without wallpaper, so the effect will be better.

Fifth, how to paste wallpaper - the wallpaper glue softens.

After applying glue to the back of the wallpaper, fold it in half to soften for a while. However, when gluing, a protective tape should be pasted, so that the surface layer of the wallpaper will not be stained with glue when folded in half.

Sixth, how to paste wallpaper - wallpaper paving.

Some auxiliary tools can be applied when pasting wallpaper to make the paving effect more beautiful. Secondly, pay attention to the time when paving, if the time is too long, it will be dry, and it cannot be torn up for correction after paving.

7. How to paste wallpaper - wallpaper trimming and cleaning.

If it is an overlapping part, pay attention to the alignment of the patterns, and the overlapping parts should be divided. In addition, if there is a part of the wire switch panel, special attention must be paid to the paving, and the glue scraped on the panel should be wiped clean with a sponge immediately.

Through the above elaboration on how to paste wallpaper, I hope friends can learn some methods. Although the wallpaper is beautiful, it is necessary to pay attention to maintenance in ordinary use, and can not scrape the wallpaper with a pen or sharp things, which will not only reduce the aesthetics, but also shorten its service life.

Answer 1: Fill the hole in the wall with putty, and level the wall with a scraper. 2. Measure the size of the wall, and then measure the wallpaper based on the wall area, pay attention to the length of the wallpaper, more than the actual veneer, and then add water to the powder wallpaper glue and water to reconcile the general wallpaper with 1:3, and the foaming wallpaper with 1:3

2. Blend, or use the special glue for wallpaper that does not need to be blended, and the roller brush is stained with the blended wallpaper special glue evenly brushed on the back of the wallpaper. 4. Then put the wallpaper against the wall, and paste the wallpaper from top to bottom and from the corners to the inside with a wooden handle brush to level the wallpaper. 5. When encountering a power switch or socket, cover the wallpaper first and then brush it flat with a wooden handle, then use a utility knife to draw a cross diagonally on it, use a scraper against the edge of the switch, and use a utility knife to cut off the excess part.

6. If you encounter a connection by the printed wallpaper, find the consistent position of the pattern at the junction of the two wallpapers, overlap and paste about 12cm wide, and after the whole wallpaper is all aligned, use a scraper to resist, and then cut off the overlapping part with a blade. 7. Pay attention to pasting wallpaper from top to bottom, if you find uneven floating paste, you can use a towel to wet it, and then re-level it with a scraper. 8. Finally, the wallpaper around the door and window is processed in the same way as the wallpaper at the power switch.

9. After the wallpaper is pasted, the original device is installed.

Question: I bought the glue on the original paper, is it right for the gaps.

1. If the wall is uneven, fill it with putty, measure the height of the wall, and cut the wallpaper according to the height. 2. Mix glue and water together, and use a roller brush to brush the glue on the back of the wallpaper. 3. Lean the wallpaper against the wall, from top to bottom, from the corners to the inside, and the wallpaper should be flat.

4. After pasting the first sheet, the second sheet and the first sheet overlap by 1-2cm, and the pattern should also be aligned. 5. Paste the wallpaper in the same way. ”

First figure out whether it is a lime wall or a putty wall, if you touch the white powder, it is the putty wall, polished. For rooms of less than 20 square meters, you also need to use a lot of paper (I mean 5 square meters). Wallpaper is done by professional construction personnel, not the old-fashioned pasted newspaper, if it is a flower wallpaper will have a problem with flowers and splicing, you can't get it.

And there are corners, even if you can crop, you can guarantee that it will not be crooked. ,Must be particularly right? Sometimes strong is not necessarily straight, the error is small, but it is difficult to see by visual inspection, this needs the support of infrared, you don't have professional equipment, so, don't paint trouble.

Let's ask someone to post it for you.

Tells you the steps to paste wallpapers:

1. It must be ensured that the wall is strong in putty, the wall has good water absorption, and is not wet.

2. The wall is flat, there is no obvious pit mark, if there is a pit mark, it needs to be filled in time, and the uneven wall will affect the appearance.

3. Brush a layer of base film before pasting wallpaper, which is something that must be used to paste wallpaper, just like stir-frying to put oil, no.

What is the density concentration of the base film of the tube brush, it must be brushed.

4. After brushing the base film, you can paste the wallpaper, and the wallpaper glue also has a lot of knowledge, some are brushed on the paper, some are brushed on the wall, and some materials can be both, and then it is spliced on the wall.

Tips for sticking wallpaper:

When pasting wallpaper, you should use a special flat brush with appropriate soft and hard to brush the flat wallpaper, and brush off the wrinkles and bubbles in it, but it is not advisable to apply excessive pressure, so as not to shrink the plastic wallpaper too tightly and produce shrinkage afterwards.

When dealing with the area around the light switch and socket, first turn off the power, cover these areas with flat wallpaper in the normal way, and then cut the wallpaper covering the switch and socket from the center to the four corners. Then loosen the screws, fold the paper edge of the cut into the cover, and then cut off the excess.

1. Remove the original paint, wallpaper and other decorations on the wall first. If there are gaps and potholes on the wall, you should use gypsum powder to fill these parts, and if you touch the sand-plaster wall and partition wall, remember to use glass filament to cover the wall and paste it again.

2. Paste the wallpaper to cut the wallpaper first, first survey the height of the wall top to the baseboard, and then cut the wallpaper. For the wallpaper that does not go to the flower, it should be cut according to the height of the wall height of 10cm, so that it is easy to use the upper and lower trimming bridges.

3. The next procedure is to brush the base film to scrape putty, do not ignore the process of brushing the base film, and the decoration paste wallpaper brush base film can avoid the wall absorbing wallpaper glue, so that the wallpaper is close to the wall, and the wall is more flat. Brush the bottom film first, pay attention to the appropriate thickness; Then scrape putty and polish, batch scrape 2 times. After sanding the sensitive spirit, paint the wall evenly with a base film.

4. Formal preparations have begun to decorate and paste wallpaper. First of all, the decoration wallpaper should be in the order of vertical and then horizontal, first up and then down, and first high and then low. After drawing the vertical line, start paving, and pay attention to the symmetry of the flower wallpaper when paving, so as to prevent damage to the overall sense and aesthetics of the wallpaper.

5. At the same time, the decorative wallpaper should be rolled in the same direction when rolling glue, and the roller and the wallpaper should be gently brushed at 45 degrees. Do not roll back the brush, so that it is easy to wrinkle the wallpaper, gently flatten it by hand from top to bottom, from the middle to both sides, and then use a scraper to scrape, so that the wallpaper and the wall are close together.

6. When pasting the second piece of wallpaper, overlap 20 with the overlap of the first piece of paper, and then cut off the overlapping position with a wallpaper knife and scrape it flat with a scraper. If there are bubbles when decorating the wallpaper, you should use a utility knife to cut the bubbles, squeeze the glue into the opening, and wipe off the remaining glue with a suitable wrench.

Methods of wallpaper: check the wall, do a good job of ground protection, measure the size of the wall, cut the wallpaper, glue and soften the wallpaper, paste the wallpaper, and clean the wallpaper. Tip: Pave from top to bottom, prohibit ventilation.

First, the method of pasting wallpaper.

1. Check the wall: First of all, check the wall, in addition to keeping the wall clean and flat, but also check the pH of the wall. If the wall has been painted before, it will take more than 15 working days for the wall to dry before the wallpaper can be pasted.

2. Do a good job of ground protection: Generally, when the wallpaper is pasted, the ground has been laid with floor tiles or floors, so before the wallpaper construction, a layer of plastic film should be laid on the ground. This film protects the floor well by avoiding falling glue from staining the floor.

3. Measure the size of the wall: measure the wall surface to be pasted with wallpaper, and calculate the amount of wallpaper. For example, the width of the wallpaper to remove each protective edge is its shortest distance, and the height from the top of the wall to the baseboard is the shortest height of the wallpaper.

4. Cutting wallpaper: When cutting wallpaper, the height of each wallpaper should be larger than the actual size of the wall length, generally about ten centimeters. Second, the remainder of the crop can be kept for later repairs.

If there is an extra beam in the middle of the complete wall, then the beam can be without wallpaper, so the effect will be better.

5. Glue softening on the wallpaper: use a scraper to evenly coat the glue on the wallpaper, and then fold the wallpaper in half to soften it for a period of time. In addition, when gluing, an orange protective tape should be laid so that the surface layer of the wallpaper can be folded in half to avoid the glue on the surface.

6. Wallpaper pasting: When pasting the wallpaper, you can use an instrument judge to keep it horizontal and vertical, and you should also make a surplus of its upper and lower positions. Secondly, the action should be fast when pasting, otherwise the glue will not be able to stick if it dries, and you can't tear up the wallpaper that has been pasted and then paste it.

7. Wallpaper trimming and cleaning: If it is a wallpaper with a pattern, then pay attention to whether the pattern is aligned when the pattern coincides, and also cut the overlapping parts. In addition, the switch panel must be straightened when pasting, so that the effect is good-looking, and the excess glue at the wallpaper splicing should be cleaned with a rag in time.

Second, the skills of sticking wallpaper.

1. From top to bottom, from high to low, first vertically and then horizontally arranged in order to lay wallpaper. When laying wallpaper for the first time, you should first find the baseline, then pave according to the laying order, then gently press it with your hand to smooth it, and then scrape it flat with a scraper.

2. If the wallpaper is immediately ventilated after pasting, it is easy to cause the wallpaper to warp and bulge. Before the wallpaper is completely dry, the heating or air conditioning should never be turned on indoors, otherwise it is easy to cause the wallpaper to open and crack due to thermal expansion and contraction.