HOW TO SET UP IP AND ADMIN YET?

I don't know if you have a web environment set up. If you don't have an environment, you won't be able to access the web page normally. The normal steps are as follows:

1. Register a domain name.

2. Purchase a server.

3. Filing.

4. Build a first-class environment.

5. Install the ** program.

6. Enrich the content.

The fourth step is to configure the interface of the PHP environment that can be visualized early, which requires the configuration of a third-party one-click PHP package. Fortunately, there are panels in this area in China, which can be used for free.

Regardless of whether you are using a win server or a Linux server, you can successfully configure the visual operation interface with the help of the three-way board, and deploy the environment with one click. Because there is a lot of content in this area, Jue Tongque can't write so much content here, so you can leave a message or search for relevant content on our blog, Lao Wei has written many tutorials, and the content is very detailed to help you get started.

You need to bind and resolve the domain name to your corresponding IP and web page. Generally, it cannot be directly accessed by using an IP address.

To establish a remote IPC$ connection, the following conditions must be met to perform administrative operations:

Have the password of the super administrator who connects to the target system;

The remote machine has the Sever service enabled, which is generally enabled, unless this mode is specifically prohibited;

Learn about commands like .net use.

In the virtual DOS under Windows (i.e. cmd), type: net use ipc$"Password "user:"adminstrator"

After the operation is successful, you can connect remotely through the local registry or service items, and there is this command in the first drop-down menu. Remotely change services or registries.

You can also imply the shared disk of the target server to your local computer. net use z:\\

After completion, I can see the Z drive letter in my computer, that is, the C drive of the remote machine. You can start with normal document management.

net use \\ip\ipc$ "passwrod" /user:user

This establishes an IPC$ channel.

Each disk is shared by default, and only ip c$ is required so that it can be accessed. However, 1. Turn off the firewall in the win7 control panel. See if you can access it.

If not, 2. Enable the administrator account and set the password. ip c$, username administraotr, password just set.

First press and hold the small black dot behind the router,Press ten seconds to reset and then connect to the wireless,Enter your router address in the browser is generally or will be written on the general manual,The default account password is generally admin or account admin password 123456 This will allow you to enter the router settings interface.

If the browser doesn't open,Restart it and try.。。。 If that doesn't work, factory reset...

Generally, there is a small round hole in the back of the router, find a needle or other sharp object to poke inside. The router is factory reset. The default password and account number are admin, some router management addresses are, and some are.

You can take a look for yourself. Then open it with a browser, enter the account password, and modify the login password in the system tool. . .

Forgot your router password?

Generally admin admin

dlink is: admin empty.

try it

If the login prompts an error in the password and you forget the password, you can reset and refill it. Or try guest guest

Take it to the computer store and ask, small question.

Each brand should have a manual, into the ** setting.

The first sailer first initializes and resets the router in the incoming state, restores the factory settings (very important), and then connects the computer network card with the LAN port of the router with a network cable to turn on the power of the router; computer network card settings;

Enter the default username: admin and the default password: admin; Click OK.

1. Set up the dialing Qi Rang:

Click Setup Wizard in the left rail, click Next;

Click on the WAN port settings, select the dynamic IP, and click Next;

Enter the bandwidth, password, and click Next;

2. Set the wireless wifi password

There is also an option on the left in the wireless setting, there is an SSID, this is wifi wireless, there is a password setting after setting, the password is as complex as possible, the best alphanumeric symbol combination;

3. Set a login password.

Change the default admin and admin login passwords to prevent someone from breaking the password and modifying the router after rubbing the network.

Click Save and restart, and you're done.

The computer should be directly connected to the landlord's network cable with dynamic IP, and the router WAN port should also use dynamic IP when using the Internet to inform the mountain.

Indicate that your router caller is a telecom router.

Router settings.

2. Enter the username and password, the default username and password of the router are generally admin, if it is modified, log in with the modified username and password;

3. If you use it for the first time, you can go step by step with the setup wizard;

4. You can also set it directly, click [Network Parameters] - WAN Port Settings], then enter your Internet access and password, and then save;

5. Click [Wireless Network Settings] - Basic Settings], give your wireless network (wifi) setting name, and save;

6. Click [Wireless Network Settings] - Wireless Security Settings, set your WiFi password, and save;