How to change the brake pads of the Golf 7 electronic parking brake

Remove the rear wheel, connect the diagnostic instrument, and lift the vehicle;

2. Turn on the ignition switch, release the handbrake (the rear wheel can rotate freely), and enter the test program;

3 into the 53 parking brake system;

4. Enter the basic settings of the 04 system;

5. Input channel number 007, which can listen to the sound of the rear wheel turning with a motor for about 5 seconds. The two rear parking brake motors are retracted. The top sub-pump can remove the old brake pads;

When replacing the rear wheel brake pads, if the "007" channel is entered in the "basic setting", if the decoder prompts "there is no such basic setting", then the self-learning process of the wheel cylinder ejection and retraction three times is carried out in the basic setting 010 (this process is longer, wait for the brake cylinder to have no sound, and then do other steps). Then execute 007 again in the basic settings

6. Replace the two rear wheels with new brake pads, after installation;

7. Enter 04 system basic settings and enter 006The sound of the motor turning on the rear wheel can be heard for about 5 seconds. The two rear wheel parking brake motors are ejected and reset.

8Clear the fault code, turn off the ignition switch, and remove the diagnostic instrument! Load the wheels and test the run.

In the case of an Audi A8L Q7, you also need to enter the thickness of the brake pads (not required for the A6L).

9 Enter the 10 channel to adjust the match (note: it is a 10 match and not the 04 basic setting).

10. Enter channel number 06

11. Enter a new matching value (that is, the thickness of the brake pad, the general range is between 9-14, the thickness of the brake pad can be measured with calipers, and the thickness of the new brake pad is generally 12). Enter 12.

12 Press OK, and the screen shows that the channel is matched successfully.

13Clear the fault code, turn off the ignition switch, and remove the diagnostic instrument! Load the wheels and test the run.

From: zgg2017 > Troubleshooting Cases

How do I change brake pads for an electronic parking brake?

**Replacement of Audi A6L A8L Q7 brake pads.

Audi A6L A8L Q7 rear brake pad replacement and oil maintenance light reset to zero (A8L and A6L are the same.

Practical technology] Audi A8 replacement brake pad matching!

**How to replace the rear brake pads for the Audi A6 A6L.

It can be replaced with a diagnostic device.

If you find that the braking effect of the car is not satisfactory, we can adjust it ourselves. The premise is that the brake pads of the car are not exhausted, and the ants are still in the normal and used working range.

Car handbrake adjustment method:

Our handbrake levers generally have an adjustable compensation mechanism underneath the handle, and the corresponding nut will be in this position.

Locking can extend the length of the brake cable, of course, the adjustment mechanism of some cars is set at the bottom of the car, if it is not convenient to adjust, then it also needs to be handled by professional personnel.

The car handbrake is not really a sophisticated build, except for the electronic handbrake.

In addition, most of the handbrakes that pull the rope, the automatics on his left and right sides are not uniform. If you use the handbrake to brake at high speed, it is easy to cause the braking strength on both sides is not stuffy, and the risk of sideslip is very high when the unilateral rear wheel is locked, the correct approach is to slow down at high speed by downshifting at a speed below 20 Use the handbrake to assist the brake, note that the handbrake is only envy and is assisted.

Volkswagen Golf ( Check price |Detailed explanation of the model ) 7 How to disassemble the brake pads? Auto Network: I'll answer for you.

Volkswagen Golf 7 brake pad replacement steps:

1.Before replacing the brake pads, you should first open the lid of the brake fluid reservoir in the engine compartment to see the height of the brake fluid page, if the brake fluid page is above the maximum limit, you should suck out some of the brake fluid to prevent the brake fluid from spilling during the replacement process.

2.Prepare the brake pads to be replaced and remove the wheel where the brake is located. In the process of dismantling, it is necessary to avoid scratching the rim of the wheel.

3.Use a wrench combined with the sleeve to remove the bolts of the brake caliper, and then remove the brake leather and spring pants (if there is a brake induction line, the brake induction line should be removed first). Observe whether the brake pads are overworn, or cracked, and if so, replace them in the next step.

4.Since there will be a lot of sand or mud in the brake calipers, it is necessary to remove them with a rag and then apply sound muffling paste to prevent abnormal noises when braking.

5.Use the piston pressure pump to press the piston to the position that cannot be pressed, then install the brake pads on the brake caliper, install the new brake pads in place (those with brake induction wires should also be installed), tighten the guide bolts, and the installation is completed.

6.After installation, cover the lid of the reservoir, enter the car and press the brake pedal a few times, and reset the brake. Then observe the brake fluid height and be within the appropriate height range.

7.After changing, test drive to check whether the braking effect is reflected.

General comment: When it comes to golf, how much will awaken the dream of "small steel cannon" in the hearts of young people, the first generation of Golf was born in 1974, and has gone through seven iterations in its 30-year history, even now, the classic shape of the Golf is still the recognized blueprint for compact hatchbacks.

Volkswagen Golf 7 brake pad replacement steps:

1.Before replacing the brake pads, you should open the lid of the engine compartment brake fluid reservoir to see the height of the brake fluid page, if the brake fluid page is above the maximum limit, you should suck out some brake fluid to prevent the brake fluid from spilling during the replacement process.

2.Prepare the brake pads to be replaced and remove the wheel where the brake is located. During the dismantling process, avoid scratches on the rims.

3.Use a wrench combined with the sleeve to remove the bolts of the brake caliper, and then remove the brake pads (if there is a brake induction line, the brake induction line should be removed first). Observe whether the brake pads are overworn, or cracked, and if so, replace them in the next step.

4.Since there will be a lot of sand or mud in the brake calipers, it is necessary to remove them with a rag and then apply sound muffling paste to prevent abnormal noises when braking.

5.Use the piston pressure pump to press the piston to the position that cannot be pressed, then install the brake pads on the brake caliper, install the new brake pads in place (those with brake induction wires should also be installed), tighten the guide bolts, and the installation is completed.

6.After installation, cover the lid of the reservoir, enter the car and press the brake pedal a few times, and reset the brake. Then observe the brake fluid height and be within the appropriate height range.

7.After changing, test drive to check whether the braking effect is reflected.

Summary. In general, if you change the electronic parking brake module of the Golf 7, you will need to match the new module. This is because the electronic handbrake module is a safety measure that ensures that the vehicle can come to a secure stop when parked, and therefore needs to be properly matched with the vehicle's other systems.

In general, if you change the Golf 7's electronic parking brake lift module, you will need to match the new module to the pants. This is because the electronic parking brake module is a basic safety measure that ensures that the vehicle can come to a secure stop when parked, and therefore needs to be properly matched with the other systems of the vehicle.

Excuse me, but please go into more detail?

After the replacement of the electronic parking brake module, it needs to be programmed and matched to ensure that the new module communicates correctly with other systems such as the vehicle's control unit and sensors. This usually requires the use of specialized diagnostic tools and techniques, so it is recommended that you seek the help of an experienced professional technician or repair facility when replacing the electronic positive base brake module to ensure safe and correct operation.

How many kilometers does the Golf 7 brake pads change their line fingers? How many kilometers do Golf 7 brake pads change? Generally, the brake pads of automobiles can be replaced for 5-60,000 kilometers, but they will vary according to different driving habits.

Golf 7 brake pads are replaced once every 40,000 kilometers, and the replacement method of brake pads is as follows: 1. Open the engine compartment to check the height of the brake fluid page to prevent the brake fluid from overflowing during the gear replacement; 2. Remove the wheel where the brake is located; 3. Remove the bolts of the brake caliper and remove the brake pads; 4. Install new brake pads and tighten the guide bolts. The Golf 7 body size is:

It is 4296mm long, 1788mm wide, 1471mm high, and has a wheelbase of 2636mm, and is equipped with a naturally aspirated engine with a maximum horsepower of 116ps, a maximum power of 85kW, and a maximum torque of 200Nm. @2019

Summary. Volkswagen Golf 6 hand brake adjustment can be changed to electronic handbrake manual handbrake can be changed to electronic handbrake, but the owner needs to go to the local vehicle traffic management center to apply for the record before changing the electronic handbrake, and then go to the professional modification center to modify the vehicle. Try to avoid their own modification, because the modification of the electronic parking brake, need to change part of the vehicle's circuit, if non-staff operation, the circuit connection is incorrect, easy to damage other parts of the vehicle, if the wrong line may threaten the owner's driving safety.

The use of the electronic handbrake equipped with the vehicle is much more convenient than the manual handbrake, when the handbrake needs to be used, there is no need to pull the handbrake lever as hard as the manual handbrake, the main force of the car is not enough, the handbrake will not be in place, and the electronic handbrake is much smaller than the space occupied by the manual handbrake, and only need to reserve a button position.

Volkswagen Golf 6 hand brake adjustment can change the electronic handbrake manual handbrake can be changed to electronic handbrake, but the owner needs to go to the local vehicle traffic management center to apply for the record before changing the electronic handbrake, and then go to the professional modification center to modify the Suidouyuan vehicle. Try to avoid their own modification, because the modification of the electronic parking brake, need to change part of the vehicle's circuit, if the non-staff operation guesses, the circuit connection is incorrect, easy to damage other parts of the vehicle, if the wrong line may threaten the owner's driving safety. The use of the electronic handbrake equipped with the vehicle is much more convenient than the manual handbrake, when the handbrake needs to be used, there is no need to pull the handbrake lever as hard as the manual handbrake, the main force of the car is not enough, the handbrake can not be pulled in place, and the electronic handbrake is much smaller than the space occupied by the manual handpin brake, and only need to reserve a button position.

How much did it cost?

c about 1,000 yuan.

Well, I'm going to buy it, how to buy it???

It is recommended to go to the car shop and let a professional master help you install it.

It reads as follows:

The Golf 7 has an electronic parking brake to start the button, this button is on the left side of the gear lever, the button has the words "auto hold", the front is pulled up, and there will be a bright spot on the button, indicating that the automatic parking brake function is in effect; Press down and the light goes out, indicating that the automatic handbrake function is invalid.

Model Description: As one of the most successful models in the world, the Golf has been around for 37 years and has more than 26 million users worldwide. After six generations of innovation, the unique innovation of each generation of Golf has led the fashion trend in the automotive industry, and has become a representative of German cars with a rigorous attitude and the pursuit of quality perfection. The Golf, which has been on the market for just over half a year in China, has also broken people's stereotypes of compact hatchbacks, not only has it continued to sell well in the market, but even there has been a rush to buy a car, and the reason for this is that its outstanding product value has already determined the hot market performance.

FAW-Volkswagen Golf was launched in Changchun on October 19, 2009.

FAW-Volkswagen's "masterpiece sincerely" sixth-generation Golf adopts the latest European design style and Volkswagen's new design language, the shape is more dynamic and fashionable, and the clear, concise and powerful image marks the future development direction of Volkswagen. The perfect body proportions, harmonious and beautiful body lines, combined with the smart headlights and simple tail design, not only make the Golf more personalized and three-dimensional, but also ensure sufficient interior space, more comfortable and practical.

To the left of the gear lever, there is a button with the word p.