Why doesn t the meter turn, but the electricity is normal

This is due to the failure of the meter caused by your use of high-power appliances. There are two solutions: one is to let it be natural, ignore it, if there is about 30-50 degrees a month, the power supply bureau will not suspect it, within 10 degrees.

The power supply bureau will ask you to change the meter, which will cost about 100 yuan. The second is to immediately report to the power supply bureau and ask for a meter change. Don't touch the meter yourself, otherwise you will bear the consequences. Good luck.

You're taking advantage.

Don't do it yourself and do things that don't hurt you. Anyway, it will not affect the use, and it will not burn the meter.

If the meter does not turn, there is no basis for the relevant departments to take fines to treat you, let alone relevant evidence, and there is no evidence of how much you are fined. Monthly routine inspections are the responsibility of the power department, and equipment failure does not affect your use, and it has nothing to do with you. Who stipulates that you must check the meter once a day.

None of them were able to win the lawsuit. It stands to reason that it is an obligation to inform them, but for these money strings that only collect money and do not serve them. You say "I don't know" and they are helpless.

It may be that the eddy current magnetic field of the meter is broken, this kind of problem is better not to touch it yourself, call the people of the power supply bureau to deal with it, otherwise they will suspect that you are stealing electricity or intentionally breaking it, and then you will be fined, because the meter is theirs, notify them now, and they will deal with it.

You're taking advantage.

This is because the register of an electronic energy meter is driven by electronic pulses.

The situation in your home should be a quality problem with the register (misaligned, stuck).

The power line is good, but there is a fault inside the meter.

Stealing electricity is an illegal act, and you can't ask about it, let alone do it. Now the city has basically replaced the electronic meter, the sensitivity is higher than the old mechanical meter, it is impossible to find a master who understands electricity like the old watch, you can pay less electricity.

The staff who charge are not stupid, and they will come to you to find out the reason for the sudden fluctuation of your electricity consumption. Remember not to do these things, if you want to use cheap electricity, you can go to the mountains where there are small power stations to build factories, small power stations are cheap electricity is not illegal.

Meter considerations.

The starting current of the meter is about the rated current when the power factor is 1, so a 10A meter will only start to rotate when the current passes through, and its power is equivalent to 12 24 watts on a 220V line.

Although the meter is a precision instrument, there is still unavoidable mechanical resistance when it is rotated. At the beginning of the rotation, the accuracy of the meter is not high because the prime mover torque is not much different from the mechanical resistance.

The meters are sealed and cannot be opened, but it would be easy if they could be opened. The easiest way to keep the meter from turning is to loosen one end of the transverse connector next to the meter inlet line, then break it to the side, and then tighten the screws.

The wiring does not move, but the electricity does not go to the meter. Another way, which is more complicated but more hidden, is to use a magnetic field to make the watch go slowly or not. If it's an electronic meter, you have to use a jammer, it's complicated, you won't.

Besides, why do you want the meter not to go? Just look at the title and you'll know what you're going to do. Don't do bad things!

I'll tell you if these are the "sin of teaching others how to sin"? Hey.

2.It doesn't matter if it's single-phase, two-phase or three-phase, the principle is the same, they flow through the meter like a stream of water, and the meter records the amount of flow like a counter. How to make the number less is to reduce the amount of electricity flowing through the meter.

3.The meter is actually an electrical appliance, as long as we short-circuit it with a wire, then the current flowing through the meter will be less or nothing, and this is our method. The meter will have a live wire connection inlet and a neutral wire connection inlet, as well as a live wire outlet and a neutral wire outlet, we only need to connect a copper wire between the two live wires, so that the meter will be.

Summary. Hello, glad to answer for you. Pro, you can make the meter not turn, if you can move the meter, open the meter wiring cover, put the first foot of the meter and the second foot have a metal connecting piece, unscrew it, as long as it can not be touched, the meter will stop, want it to turn, tighten it OK.

How can I keep my meter from turning?

Hello, glad to answer for you. Pro, you can make the meter not turn, if you can move the meter, open the meter wiring cover, put the first foot of the meter and the second foot have a metal connecting piece, unscrew it, as long as it can not be touched, the meter will stop, want it to turn, tighten it OK.

The second method, in the first pin (live wire incoming) and the third pin (live wire outgoing), connected with a copper wire, the meter will rotate slowly, if it is a large meter, a month with 5-600 degrees, may only turn about 60 degrees.

Legal Analysis: No. There are two types of electricity bills, one is the meter with the card, and the other is the smart meter.

If the card is in arrears, the power will go out.

Before the arrears, when the balance is less than 10 15 20 yuan (different places), the system will send you an SMS. After the arrears, there will be a text message notification first, if you haven't paid yet, there will be a manual call ** to notify you to pay the electricity bill in a few days. If you do not pay the bill, the incoming call must be manually activated after the power outage is due to arrears.

Legal basis: "Power Supply Business Rules" (hereinafter referred to as the "Rules") Article 67 Except for the suspension of power supply for any reason, when a power supply enterprise needs to stop the power supply to a user, it shall go through the power outage procedures in accordance with the following procedures:

1. The user, reason and time of the power outage shall be reported to the person in charge of the unit for approval. Approval authority and procedures shall be formulated by the provincial power grid operator;

2. Within three to seven days before the power outage, the power outage notice shall be delivered to the user, and the power outage notice shall be submitted to the power management department at the same level for the power outage of important users;

3. 30 minutes before the power outage, the user will be notified of the power outage time again, so that the power outage can be implemented at the time specified in the notice. Combined with the provisions of Article 66 of the Rules, it can be seen that if the arrears of electricity charges are still not paid after being notified and urged, the power supply can only be suspended with approval.

Summary. It may be because the slotted gear wire falls off the wire board, in this case, the slotted gear wire needs to be re-fixed on the circuit board; If the gear teeth fall off, the gear teeth need to be fixed again, or the gear frame is too tight, and the gear frame can be loosened; Miswiring causes a short circuit in the wires and burns out the meter, so it is recommended to replace the meter directly.

The newly installed meter does not go, but the electricity can be used normally, what is the matter?

It may be because the slotted gear wire falls off the wire board, in this case, the slotted gear wire needs to be re-fixed on the circuit board; If the gear teeth fall off, the gear teeth need to be fixed again, or the gear frame is too tight, and the gear frame can be loosened; Miswiring causes a short circuit in the wires and burns out the meter, so it is recommended to replace the meter directly.

Here are a few possible reasons.

Hope it helps,

Summary. There may be several reasons why the meter does not rotate but can be used normally: 1. Internal mechanical failure of the meter

The internal mechanical parts of the meter may malfunction, causing the meter to not rotate properly, but it can still be used normally. 2. The external environmental impact of the meter: the external environmental temperature of the meter is too high or too low, or there is a strong magnetic field outside the meter, which may cause the meter to not rotate normally, but it can still be used normally.

3. Fault of the internal circuit of the meter: The internal circuit of the meter may fail, resulting in the meter not being able to rotate normally, but it can still be used normally. 4. Power failure inside the meter

The internal power supply of the meter may fail, causing the meter to not rotate normally, but it can still be used normally. In short, the reason why the meter does not rotate but can be used normally may be due to the internal mechanical failure of the meter, external environmental influences, internal circuit failure or internal power failure.

There may be several reasons why the meter does not rotate but can be used normally: 1. Internal mechanical failure of the meter: The internal mechanical parts of the meter may fail, resulting in the meter not being able to rotate normally, but it can still be used normally.

2. The external environment of Tongshi electric meter: the external environmental temperature of the meter is too high or too low, or there is a strong magnetic field outside the electric meter, which may cause the electric meter to not rotate normally, but it can still be used normally. 3. Fault of the internal circuit of the meter:

There may be a fault in the internal circuit of the meter, causing the meter to not rotate normally, but it can still be used normally. 4. The internal power supply of the meter fails: the internal power supply of the meter can fail, resulting in the meter not being able to rotate normally, but the trembling wheel can still be used normally.

In short, the reason why the meter does not rotate but can be used normally may be due to the internal mechanical failure of the meter, external environmental influences, internal circuit failure or internal power failure.

I'm still a little confused, can you be more detailed?

The reason why the meter does not turn but can work normally may be due to a malfunction in the motor inside the meter, or a faulty circuit inside the meter. Workaround:1

If the motor inside the meter is faulty, Danchayou can try to replace the motor, or check whether the power supply voltage of the motor is normal, if the voltage is not normal, you can try to replace the power supply voltage. 2.If the circuit inside the meter is faulty, you can try to check whether the circuit is connected properly, and if the connection is not normal, you can try to replace the circuit or reconnect the circuit.

Personal Tips:1Check the power supply voltage of the meter regularly to ensure the proper operation of the meter.

2.Regularly check the electrical connections inside the meter to ensure the proper functioning of the meter. 3.

If the meter is found to be faulty, it should be repaired in time to avoid greater losses.

The meter won't turn, and there is no electricity, what should I do?

Hello, I'll help you solve this problem! The operation steps are as follows: Method Step 1, first, check whether there are large power appliances in use in the room, such as rice cookers, electric baking pans, electric kettles, etc., sudden high current can easily lead to overload and power failure.

2. Second, find the leakage protector in the room to see if it trips, if the switch is below, you can push it back to the top to send power. 3. In some places in the countryside, there is no leakage protector installed, all of which are operated normally through the fuse of the gate box, after the power failure, we must pull down the switch of the gate box and see whether the fuse in the box is blown or not, if it is found that the fuse is blown, replace the new fuse in time. 4. After replacing the fuse or pushing the leakage protector switch, if it is found that it is still tripping and power-off, it means that there is a problem with the short circuit of the connected electrical appliances in the room.

5. If there is no problem after checking all of the above, the meter is not lit, and there is no electricity, you should ask your neighbor whether there is no power at present, so as to confirm that it is not your own problem, but a power outage on the main line of the collective circuit. 6. If the neighbors have electricity, and you have checked that other problems are normal, then you can conclude that the meter itself is faulty. Call the property or community maintenance**, and communicate with the maintenance personnel to repair.

Send you to follow my steps to try it, and if you have any questions, you can give me feedback in time!