Tile paving skills Two major matters to pay attention to

in our home renovation.

, paving tiles.

It is an important project. In many cases, errors will be caused by the problem of paving method, so let's take a look at the precautions in the tile paving method.

1. Lay floor tiles in the kitchen and bathroom.

Or do you want to lay the wall tiles first?

Lay the wall tiles first, and then pave the floor tiles, if the floor tiles are paved first, and then the wall tiles are paved, you must wait for the tiles to dry and solidify and then pave the wall tiles, if the floor tiles are not completely dry, the wall tiles will be directly paved, and the floor tiles will be stepped on, which will artificially cause the hollowing, loosening and height inequality of the tiles.

2. When is it better to hook the joints when tiling the tiles?

Tile grouting is generally carried out after the tile is dry, if the tile is not completely dry and solid, it will cause the tile to be uneven and loose, so that the tile is easy to fall off when used in the later stage.

3. Why do the wall tiles sometimes fall off quickly?

in the paving of wall tiles.

when using cement. Mortar as a binder, wall tiles absorb a large amount of water, if not soaked in water in advance, the porous ceramic bricks after paving will absorb the moisture in the cement mortar. Cement requires a lot of water during the curing process, and due to water loss, it becomes unadhesive and has no strength, and the bricks fall off the wall along with the cement mortar.

4. Why should there be joints when paving floor tiles?

On the one hand, it eliminates the impact of product size deviation, and on the other hand, it avoids thermal expansion and cold contraction, which causes products to squeeze each other, resulting in bulging or peeling. Polished tiles.

Generally, leave 1mm, porcelain 2-5mm, antique bricks.

5-8mm。

5. Why is the sewing more and more wrong when paving porcelain tiles?

This is because the same plane is paved with products of different working sizes, especially when different products are matched, the working sizes are inconsistent.

6. What is the reason for the unsatisfactory pattern effect after the product is paved?

Most of the products have a certain pattern and directionality, according to the product pattern characteristics or the back of the trademark pattern unified direction paving, can obtain a satisfactory paving effect.

7. Why is there a color difference in the polished tiles after paving?

After paving, different positions may be in different light conditions, resulting in visual color aberration; During construction, the color number on the packaging box was not seen, and the bricks of different batches and different colors were paved together; When the product leaves the factory for grading, the color is mixed, and the bricks of different colors are mixed together.

8. Are the wall tiles laid horizontally? Or is it better to pave it vertically?

The horizontal and vertical tiles of the wall mainly depend on the size and structure of the space. If the bathroom.

Kitchen. The area is small, but the inner space is high, and the horizontal paving can be used to visually connect the large space area and reduce the inner space; If the bathroom and kitchen are short, the vertical laying can achieve the effect of making up for the visual defects. On the other hand, horizontal and vertical paving also depends on personal preference.

That's all about tile paving.

I hope that the introduction of the precautions for method problems can be helpful to you.

Ceramic tiles are attached to the surface of the house, so it can be seen as the "face project" of the house. After a lot of hard work to buy a good tile suitable for yourself, paving has become the theme of the future face project. Tile paving has relatively high requirements for construction, and it is easy to cause problems such as hollowing of tiles if you are not careful.

How do you make the perfect tile? The answer is in the article.

The first part of the installation of seam and hook seam skills

1. Suggestions for leaving joints in commonly used tiles for decoration

When seamless bricks and other wall tiles and polished bricks are paved, the size of the joints should generally be around the left, not less than 1. Air nails can be used as a reference. The general seam of antique brick is slightly wider, generally 3--5mm.

The cultural bricks on the exterior wall of the balcony are generally about 5mm with a seam.

2. Selection of seam material and time

Generally, the time of joint selection is 24 hours after tiling, that is, after the tile is dry, the joint time is too early, which will affect the tiles pasted, resulting in unevenness or loosening and falling off. In addition, before hooking, it is necessary to clean up the dust and debris in the cracks of the tiles.

Nowadays, the materials commonly used in grouts are mainly cement, grouts, putty powder, etc. Among these materials, putty powder and white cement are the more traditional materials, and now they are used as the main joint materials.

Putty powder, white cement waterproof performance, scrub resistance is poor, now, in the process of home decoration, in the kitchen and bathroom wall floor, living room floor tile joints are generally not used, now basically choose professional tile caulk (also known as grout).

The second part of the tile installation precautions

1. Pay attention to the density of paving

When paving, pay attention to the gaps of the tiles and the compactness of the cement mortar. The hollow drum rate of tiles accounts for less than 5% of the entire wall tile surface, which is normal.

When purchasing, pay attention to the selection of high-quality tiles, which is the premise of ensuring the quality of ceramic tile paving. Due to the construction process, the construction personnel may propose that the wall flatness error is large, and some measures need to be taken to make up for it alone, if it is necessary to increase some scattered costs, consumers should give support and cooperation as much as possible according to the situation.

2. Grasp the draft time of tiles

The so-called tile draft is to soak the tiles in water in advance for a period of time, generally about 2 hours, and the actual operation can be analyzed according to the specific situation of the density of the tile. Before laying the tiles, it is also necessary to pay attention to the fact that the tiles should be soaked in sufficient water, so that the tiles can completely eat enough water, so as to avoid the hollowing and falling off of the tiles.

The traditional method of tile paving is to use cement mortar for paving. First of all, the ratio of cement mortar should be reasonable, and the general practice is that the volume ratio between the two is 1:1.

If in this case, the tile is still hollow, in addition to the low technical level of the workers in the paving process, the main reason is that the draft of the tile is not enough in the early stage. This is done to ensure that after the tile is pasted to the wall, the moisture in the cement mortar will not be snatched away by the tile, so as to achieve its highest strength, so as to prevent the hollowing and falling off of the tile, which is the main reason for the tile to soak in water.

The above was released on 2016-08-08, the current relevant housing purchase policy please refer to the actual situation).

In life, when decorating a house, ceramic tiles are an important material in the decoration of our house. Over time, ceramic tiles have become a very popular decorative item. So,Tile laying skillsWhat is it?

What should I pay attention to when laying tiles?

One,Tile laying skills

Tile laying skillstile joints.

Because tiles can expand and shrink due to ambient temperature, etc., we have to leave enough space between each tile when we place it. For example, when laying bricks with joints, it is better to leave a space of millimeters, and the space between the tiles is about 3-5 millimeters.

Tile laying skillsCaulking.

It is better to fill the tiles after 24 hours of mosaic. Before filling the joints, clean the tile grooves of debris. If the environment is very hot during construction, we have to sprinkle a little water on the surface of the tiles.

Tile laying skillsDip into the tiles.

Before placing the tiles, it is better to clean the tiles and soak them in water. The tiles must be soaked for more than 2 hours, and then allowed to dry the moisture on the surface of the tiles before the paving and diversion begins.

IITile laying skills - precautions for paving

1. Find a standard point.

Always check the flatness of the floor before placing the tiles. If the floor is uneven, stop placing it immediately. Of course, the most important thing in laying tiles is to find standard points, the joints must be even, and they should not be unsuitable.

Generally speaking, after fixing we can find the bottom plate.

2. Carry out waterproof treatment.

Since the replacement of ceramic tiles usually destroys the original impermeable layer of cement mortar, it is necessary to pre-waterproof. For example, before paving, an impermeable layer of asphalt can be applied, and the cement of the joints between the bricks must also be replaced.

Soak the floor tiles for about half a day, check if there is enough slope on the bathroom floor, if there is water. Masonry can only be carried out after it has been confirmed. When the steps of laying the tiles are completed, the circuit board is covered with cardboard, and it takes at least a day to walk on the bricks.

You can get it for free

When decorating, there is a very important foundation project is to pave tiles, and the floor and wall are all required to be paved with tiles. When decorating and paving tiles, you need to pay attention to relevant skills, and what are the skills of decoration and tiling? Remind everyone that there are many precautions for tiling, and you need to pay special attention to the relevant rules.

First, decoration and paving tile skills.

1. The tile needs to be soaked in water before it is paved.

This does not mean that you can buy tiles that have been soaked in water, but that in the process of laying tiles, you need to soak the tiles in water before paving. So one thing is very important, that is, you can't buy all the tiles back to soak in water, after all, the purchased tiles are redundant, if they are soaked in water, it will affect the secondary sales, it can not be returned. Therefore, when soaking water tiles, it is necessary to use as many tiles as you need to use and how many tiles you need to soak!

2. Make a brick arrangement plan in advance.

Laying bricks is not something that can be paved when you want to be paved depending on your mood, and you can stop the project if you don't want to pave it. In fact, before paving the tiles, you need to do some planning, you need to first select the tiles to be paved, and you need to cut the corners in advance.

3. When there is a problem with the tile, it should be dealt with in time.

When you find that there is a problem with the purchased tile, such as missing corners, wear, etc., you need to negotiate with the tile provider as soon as possible to solve it, and you can't pretend not to see it, or feel that it is not necessary to deal with it.

Second, the precautions for tiling.

2. The ground of the old house must be fully haired, the depth of the concave is not less than, the spacing is 5cm, and then the net cement slurry is brushed. Remember not to collect water to prevent seeping downstairs through the cracks in the slabs.

3. For those with drainage slope requirements, such as toilets and baths, the slope direction of tiling should be controlled according to the corresponding slope pull line.

4. Base acceptance: the surface is smoothed and checked with a 2m ruler, the deviation shall not be greater than 5mm, and the elevation deviation shall not be greater than 8mm.

5. The variety, specification, color and pattern of stone and floor tiles should meet the requirements of the design and residents, and the surface of the veneer should not have scratches, missing edges and corners and other quality defects. Expired and agglomerated cement should not be used as a binder. Before laying floor tiles, it is necessary to make a comprehensive selection of tiles.

6. Before the floor tile is paved, it should be carefully measured and the wheel may be typeset by computer, and a reasonable plan should be selected, and the number of specific floor tiles should be counted, so as to arrange the beauty and reduce the loss for the purpose, and focus on checking whether the geometric size of the room is neat.

Decoration paving tile skills as above, decoration paving poor letter tile is a very important thing, it is also recommended that you can hand over these work to professional decoration people to complete, so that they know the precautions for tiling, can pay more attention when pasting tiles, to avoid causing a variety of tile problems to affect future life.

In daily life, ceramic tiles play an important role in interior design, and the correct way of tiling will affect whether the wall is beautiful. Today, what are the methods of paving tiles with you, and talk to you about the matters that need to be paid attention to before paving tiles.

First, what are the methods of paving tiles.

1. Adopt the traditional thick paste method.

The so-called traditional thick paste method involves applying the stirred tile adhesive to the back of the tile and then applying it to the substrate.

2. Adopt the thick paste method.

Use a toothed scraper to apply the tile adhesive paste on the working surface to make it evenly distributed and form a toothed shape. Each coating is about 1 square meter (depending on the temperature), and then the tile can be pressed on the base surface during the drying time.

3. Double-sided scraping method.

Use a brain-shaped scraper to apply the tile glue on the working surface, and then hold the tooth-shaped scraper to form 45 angles between the tooth edge and the base surface, and comb the glue layer into a uniform shape; At the same time, the glue is evenly applied to the back of the tile; During the drying time of the glue, the tiles are laid into place.

Second, the precautions for paving tiles.

1. Soak the tiles.

Before paving the wall tiles, it is necessary to select high-quality tiles, soak them in water for more than 2 hours, and finally dry the surface moisture. The tiled wall should be moistened with water.

2. Positioning of the line of defense.

Before paving, the pay-off positioning and brick arrangement should be carried out, and the non-whole bricks should be discharged in the secondary part or at the shady corner. Each wall should not have two columns of non-whole bricks, and the width of the non-whole bricks should not be less than 1 3 of the whole bricks.

3. Horizontal and vertical signs should be done before tiling.

Before paving, the horizontal and vertical signs should be determined, the bottom ruler should be padded, and the line should be paved. The surface of the wall bricks should be flat, the joints should be straight, and the width of the joints should be uniform. The yin corner brick should be pressed to the correct direction, the yang angle line should be made into a 45 angle butt, and the reed should be rotten at the wall protrusion, and the whole brick should be cut and matched, and the non-whole brick should not be used to patchwork and pave.

4. Combine mortar for paving.

1:2 cement mortar should be used for the combined mortar, and the thickness of the mortar should be 6 10mm. Cement mortar should be spread all over the back of the wall bricks, and a wall should not be paved to the top at one time to prevent it from collapsing.

Today we have brought you the method of paving tiles, we can choose the traditional thick paste method, thick paste method or double-sided scraping method when paving tiles. Before laying the tile wall, you can follow the precautions to prepare, these methods can help you pave a beautiful tile wall.