How to set up router autodialing for ZTE ZXV10H108L terminal?

Home Network Environment Cabling]:

1. There is a telecom cat: the telecom cat --- router WAN port; The LAN port of the router --- a computer.

2. No telecom modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. Open the browser - enter the general router address is this or view the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

The IP and DNS settings of the computer are automatically obtained.

1. Enter the router.

Open the browser - enter the general router address is this or check the login information on the back of the router) enter the route - enter the user name, password, (the default is generally admin).

2. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the username and password for Internet access according to the prompts, and save.

3. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

Actually, there is no need for that, as long as you plug a wireless receiver into the rest of the computer, receive the wireless network, enter the username and password behind the router, and then connect, after the connection, turn on the broadband connection, enter the broadband connection and the password for Internet access, and you're good to go.

Open the Start menu on your desktop, and then, select Control Panel, which opens.

Once you are in the Control Panel Options, click on Internet Options, click on Enter.

Then, in the Internet Options Settings, find the Connect option and click Turn On.

Then check the box in front of the automatic dial-up connection shown in the figure below to complete the setup.

Note that the path of the dial-up connection can be through the default broadband, and click OK to take effect after confirmation.

Prepare two network cables (the first one you have ready, which is the one that goes through the "modem").

The second is to buy a network cable sent by the router, if you don't send it, you have to make a network cable with crystal heads at both ends. ）

1.Change the local connection to automatically obtain the IP address.

2.The network cable that comes out of the "modem" is connected to the "wan" port on the router, and the router's ports (1,2,3,4) are either connected to the network cable port behind the computer host.

3.Open the browser and enter the password and username of the router are admin

4.Go to the router settings screen, select the PPPoE (ADSL virtual dialing) method, enter your home account and password, and confirm.

5.Then set the SSID, encryption method, and password.

6.Save, restart. In the end, the setup is considered successful.

You can flash third-party firmware, and that QoS is very good.

ZTE H108L Setup Method Attached: Route Setup Method.

When you get the device, first plug in the ** line network cable dial-up Internet to try, can go online on behalf of VPI VCI has been built into the cat, and then log in to the configuration interface of the cat to adjust the route.

Enter enter in the address bar of your browser.

The following page (1) appears.

Enter the username and password to log in to the Routing modem management page, and the username is telecomadmin

Password: ne7ja%5m (Note: The password should be cased, it is recommended to copy and paste it if it is more complicated, and there should be no spaces).

2.After logging in, click on "Network" (the one circled in red), then select a "Connection Name", select the line of your VPI VCI, and click Delete at the bottom. Delete with Nanjing as the selected Internet B 8 -35.

Commonly used VPI VCI: 8 35 0 35 0 100 8 81 0 200

At the point: WLAN configuration, select the encryption method in the security settings' in the WPA pre-authenticate shared key lock yourself, such as setting the wireless login password A123456789

4.At this point, the IP address is obtained, and the routing is set successfully. Wait two minutes after the device restarts. Internet access is available.

Open it with IE browser, enter it with a normal password, and send me the information on the first page to confirm the version information.