ZTE ZXV10 H108L V2 0 A wireless cat, seeking to crack. 70

ZTE-H108L route setting method.

When you get the device, first plug in the ** line network cable dial-up Internet to try, can go online on behalf of VPI VCI has been built into the cat, and then log in to the configuration interface of the cat to adjust the route.

1.Type enter in the address bar of your browser, click enter.

The following page (1) appears.

Enter the username and password to log in to the Routing modem management page, and the username is telecomadmin

Password: ne7ja%5m (Note: The password should be cased, it is recommended to copy and paste it if it is more complicated, and there should be no spaces).

2.After logging in, click "Network" first (and then select "Connection Name", delete them all one by one, pay attention to them when deleting, delete them to that one, and the connection will be dropped, your VPI VCI is that For example, when you delete to Interner B 0 35, it will be disconnected, then your VPI VCI is 0 35, record it yourself, and use it later).

3.Then select the connection name: "New WAN connection," then select the route mode, click PPPoE, enter the local VPI and VCI parameters, fill in the account password, and the service mode

Internet, click Save Be careful not to restart it yet Telecom may be monitoring your cat See below. Nanjing, for example. VPI VCI is 8 35 I don't know the local VPI VCI, you need to go to 10000, or the big city can also be queried.

Commonly used VPI VCI: 8 35 0 35 0 100 8 81

*The most important thing is to change the remote management in the network after setting it up, delete the ** in the first line, change the username and password, remove the tick of the periodic report, and then click on the middleware working mode on the right, select Enable middleware, do not include TR069 function (control function of telecommunications)".

4.At this point, the route is set successfully. Wait two minutes after the device restarts. Enter the cat's interface and take a look at the results of your settings.

The external IP obtained in the cat indicates that the cat has gone online.

But we're not done yet. Because now your ITV won't work.

Proceed with the setup. In the connection name, select New WAN Connection.

Binding Option: lan2

Mode: Bridged.

Business model: other

vpi=8 vci=85

Point creation. Ok, let's try ITV to work

If your broadband is adsl with a plugged ** cable, leave q or contact me directly with "hi".

Enter the cat's login interface,Username and password are behind the cat,After entering,The first is the cat's information and broadband information,The second is the network,It's also about the WLAN setting,There are three options on the left,Click on the third option,There is"Wi-Fi switch"Just click on a tick OK!

1.The computer browser opens "This is the login interface for the wireless cat settings, account: telecomadmin password: ne7ja%5m (this messy account password is the telecom administrator, you can copy and paste the past, pay attention to the number of digits)

2.After entering the wireless modem settings interface, select "Network - Broadband Settings". Take note of the VPI and VCI values in the middle of this interface.

3.After the connection name is a drop-down menu, select them one by one, and click "Delete" at the bottom of the screen to delete the drop-down menu.

4.Select "New WAN Connection" after the connection name, then fill in your broadband account (** with area code) and password at the bottom of the interface, and other settings do not need to be changed (VPI and VCI should be the same as those in the second step), and finally click "Create" at the bottom.

Setup, please skip this step if you don't have ITV. Continue to "Create WAN Connection", select "LAN 2" (that is, ITV port) for the binding option, select "Bridge" for the mode, click on the drop-down menu for "VPI VCI", select the previous step, and finally click "Create" below.

6.On the wireless modem settings page, select Network - DHCP Configuration, and enable the DHCP service checkmark (default).

7.Wireless cat settings interface, select "Network - WLAN configuration", change the name and password of WiFi (no problem if you don't change it, but the default is not easy to remember.)

8.On the Wireless modem settings page, select "Management - Device Management" and "Restart". (There is a "factory reset" below, for help).

9.Delete the "Dial-up Connection" on the computer and fill in the IP &DNS to access the Internet.

10.After connecting to wifi on your mobile phone, you can access the Internet without PPPOE.

Dear Telecom users, Hello! The broadband cat (wireless broadband cat) donated or purchased by China Telecom cannot directly use wifi wireless Internet access, and professionals need to enter the broadband cat (wireless broadband cat) configuration interface to set the routing mode before it can be used as a router (wireless router), and non-professionals cannot configure it by themselves. It is recommended that you purchase a wireless router to build a Wi-Fi environment.

In this way, the wifi device can be used according to the prompt link. At present, Anhui Telecom's broadband cat change routing mode has been liberalized. For details, please consult the local 10000 or broadband installation master.

See also the web-related cracking manual. After cracking, the IPTV cannot access the Internet, and the relevant Internet access methods (PPPOE, DHCP, IP) can be modified through the set-top box to achieve normal use. Have a great day!

If you need to buy a phone and check the phone bill, please log in to the online business hall (, hundreds of mobile phones are low prices on the whole network, and now you can also enjoy a discount of 50 yuan for 2 yuan.

Dear, the current wireless network can't be cracked. Give it up.

Try this address to see.,It'll say a file.,Change the suffix to txt and see if you should be able to find it.。

Hello, if you want to fill in the static IP, first of all, you use ZTE cat to surf the Internet, and find the IP address, gateway, DNS server and other information you need in the details of the local connection.

Remember this information, then go to the router, and fill in this information in the static IP settings.

If the gateway (login IP) of your ZTE cat is yes, it will conflict with the gateway of the router, then you need to modify the gateway of the router or the medium optical modem first.

Enter the router, select the network parameter setting, select the WAN port setting, set PPPOE, static IP, dynamic IP, select static IP, enter the IP address and ZTE wireless cat IP is the same but the last bit can not be the same, if the LAN port address is changed to other network segments in this network segment first, save it.

First of all, don't connect to ZTE cat, connect TP directly, use login, modify the WAN port to a number other than that, such as, restart, connect TP to ZTE through the network cable, after all restarts, select the computer wireless network as TP, everything is solved!

Once the router is entered, there is a wizard mode. When prompted, enter your internet ID and password, and you should be fine with the default settings.

How did this cat crack into a route, ask for advice.