What to do if the toilet always runs long, and how to solve the long running water in the toilet

There is a long running water in the toilet, which can be solved in a few simple clicks, and there is no need to find someone to repair it.

Toilet long running water solution:

1. The toilet water does not stop causing long running water, press the drain and unscrew the ** drainer to see if there is sediment at the bottom, and if there is sediment, it will not be closed tightly, resulting in long running water in the toilet.

2. Install it back after cleaning it up. Look at the float again, there is a small switch on the side, break the switch, the upward water level rises, the downward water level falls, adjust to the appropriate position, and then close the kitchen label There is a screw, and you can also adjust the water level by twisting the screw.

About the inspection of the toilet:

If the chain connected to the float rod of the toilet bowl is too short, the toilet will also run non-stop. In this case, the length of the chain should be lengthened appropriately. And check whether the nut used to fix the water tank has been tightened, once found loose, it should be tightened in time to ensure use.

Open the toilet tank to check if there are small sand particles at the floating position, which can easily cause blockage, and if so, clean it up in time. Then look at the sealing ring of the water valve body, if it falls off, it needs to be installed back in time, if it is damaged, it needs to be replaced with a new sealing ring.

If the water tank is hit by a large external force and is damaged, it will continue to flow to the toilet. This is where a special glue is used for repairs. If the water tank is damaged, you can only contact professional maintenance personnel to deal with it, or directly replace the new water tank.

Dear, I'm glad to answer your <>

Answer: What to do if the toilet is always running as follows: 1. First check whether the toilet flush switch is rebounded when the sail is chaotic, some flush switches have been used for a long time, the spring fails, and it is very likely that there is no immediate rebound, so the toilet will always be in a flowing state, and only the toilet needs to rebound the flush switch of the toilet.

2. If the toilet water level device is too loose or too high, it will also lead to the phenomenon that the toilet water does not stop, in this case, only need to adjust the toilet water level limit. 3. If the chain of the float force rod is too short, it will also cause the toilet to run water, so the chain length can be knotted to an appropriate length; Then check whether the water tank fixing nut is tightened, because it may be that the water tank parts are loose, tighten it. 4. Open the lid of the water tank first, see if the floating spot of the water tank is blocked with fine sand, and remove the impurities if there is.

Then look at whether the sealing ring inside the water valve body has fallen off or other debris. If the seal comes off, reinstall it. 5. There is also a possibility that the water tank has been hit by an external force, resulting in damage to the water tank and causing the toilet to run for a long time.

We can use some glue for the water tank to repair it, but of course this method is only suitable for repairing minor cracks. If the crack is too large, you can only ask a professional to replace the water tank with a new one.

1. The toilet is always running water, and it is very likely that which component in the water tank is broken, we can open the water tank of the toilet to check that the toilet tank has a component that is half like a sphere, whether it has fallen off or is damaged.

Toilet 2, if it falls off or is damaged, we can reconnect it, and if it is damaged, we can replace this component.

Toilet 3, we can bring the chain waterproof gloves, or directly into the toilet tank, the components with their hands gently shake to see if there are any components have been loosened, if there are loose components, we will fix the loose components, if damaged directly replaced, so that the problem of toilet running water can be solved in time.

1. If the tank is drained, the float and the float rod will affect the reset of the flap and cause leakage. In addition, the float is too long and the float is too large, which leads to friction with the tank wall, affects the free rise and fall of the float, and leads to seal failure and leakage. The mechanism of the tank fittings caused disturbances during operation, which led to leaks.

2. The quality is not good. Manufacturers blindly reduce production costs When the inlet pipe and inlet pipe of the injection valve are injected, the poor material will cause cracks, resulting in the failure of the seal, and the water in the tank enters the toilet bowl through the overflow valve, overflow pipe, resulting in a long flow of water.

3. When the water pressure is very high, if the buoyancy of the float is insufficient due to the excessive pursuit of the miniaturization of the tank accessories, if the float overflows, the water inlet valve can not be closed, so that the water continues to flow into the water tank, and then into the toilet, and there is a vertical situation of water leakage.

4。The height of the lift inlet valve can be changed freely, and if the seal does not fit tightly with the pipe wall, leakage may occur. The fitting of the drain valve is not tightly sealed.

Disposable drain valves manufactured in a single use cannot be tightly sealed through a fitting. When hydraulic pressure is applied, water flows into the toilet bowl through the overflow pipe from the interface gap, causing the toilet to leak.

1. The material of the water tank is not good or the internal parts of the water tank are old, due to the rapid start of the toilet industry, in the face of the broad market prospects of the toilet debate, many small manufacturers produce some inferior materials of the toilet tank mixed into the toilet industry, in order to seek more benefits, they choose inferior materials to produce the toilet, this kind of toilet usually does not see its good or bad in the appearance, but there may be some small parts inside that are not used, it is easy to be damaged, Of course, it is not excluded that the toilet tank has been used for a long time, and it will also age and deteriorate if it is used for a long time, which is a natural aging process, and the quality of its products is beyond criticism. 2. The leakage of the flush toilet may also be due to the problem of the sewer pipe below, which is mainly connected to the toilet tank to transport water, and the possibility here is also very large. 3. The drain valve of the toilet is mainly in charge of the water of the toilet tank, generally speaking, in the case of many troubles, it may cause problems with the toilet drain valve, which may be caused by the cracking and deformation of the installation hole, or the uneven and uneven installation surface and a series of reasons caused by the lack of care during installation.

1. The material of the water tank is not good or the internal parts of the water tank are old, due to the rapid start of the toilet industry, in the face of the broad market prospects of the toilet, many small manufacturers produce some inferior materials of the toilet tank mixed into the toilet industry, in order to seek more benefits, they choose inferior materials to produce the toilet, this kind of toilet usually does not see its good or bad in the appearance, but there may be some small parts inside the notice, it is easy to be damaged, Of course, it is not excluded that the toilet tank has been used for a long time, and it will age and deteriorate if it is used for a long time, which is a natural aging process, and the quality of its products is understandable.

2. The leakage of the flush toilet may also cause the problem of the sewer pipe below, it is a pipe that transports water to be connected to the toilet tank, and the possibility here is also very large.

3. The drain valve of the toilet bowl is mainly in charge of the water of the toilet tank, generally speaking, in many cases, it may cause problems with the toilet drain valve, which may be caused by the cracking and deformation of the installation hole, or the uneven and uneven installation surface and a series of reasons caused by the installation of carelessness.