What is the cause of water seepage on the walls and floors of the bathroom?

The bathroom has heavy water vapor, and the waterproof project must be done firmly, but what is the reason for the water seepage problem on the wall and ground after the decoration? How can I avoid this problem? <>

When installing the faucet in the bathroom, it is necessary to pay attention to the installation of the inner tooth elbow, and it is best to highlight the tile surface 2-3mm, so that if there is water seepage in the faucet position, the water seepage point will be located on the outer surface of the tile. If the inner tooth elbow is installed parallel to the surface of the tile, the water seepage point must be located inside the tile, although the surface of the wall has been waterproof, but long-term soaking will also have a certain impact, and the firmness of the tile and the base surface is also damaged to a certain extent.

Tile paving for some reasons need to leave a certain size of expansion joints between the tiles and tiles, the bathroom environment whether it is the ground or the wall for a long time will have water stains, if you do not do a good job of waterproof and beautiful seams, water stains will seep into the inside from the gaps, which will also bring certain hidden dangers to daily life.

The toilet water is mainly discharged through the floor drain, and whether the floor drain installation is smooth is also the biggest problem of whether there is water accumulation in the bathroom. So if the floor drain is not well sealed, water will leak from the edge of the floor drain to the bottom of the tile.

Leaking water in the bathroom is a big problem, mainly affecting your own life and the lives of your downstairs neighbors.

Remove the floor tiles and the bottom layer of wall tiles, remove the floor tiles to expose the original ground, do it with two-component waterproof mortar, and then close the water test 24 hours after doing it to check whether the downstairs is leaking, and if there is a problem, continue to do it until it does not leak.

There is also the leakage of various valves and water pipes in the bathroom, when these are installed, wrap more raw material tape, tighten it, and screw it firmly.

There will always be multiple reasons for the occurrence of problems, but in the final analysis, there is no reasonable planning before the problem occurs, and the details are not in place. The same is true for leaks in the bathroom, and only by preventing everything in advance can the problem be reduced.

The main reason for water seepage on the walls and floors of the bathroom, many people still don't know, come and take a look, what you learn is earned, very practical.

For some reasons, tile paving requires a certain size of expansion joint between the tile and the tile, if the waterproof and beautiful seam are not done, water stains will seep into the inside from the gap.

1. Water seepage on the wall caused by pipeline leakage. 2. Water leakage of the waterproof layer leads to water seepage on the wall. 3. Water leakage caused by improper paint. 4. The use of non-insulating materials causes water leakage.

Water seepage on the bathroom floor means that the waterproof coating was not carefully applied in the early stage, resulting in water seepage.

Summary. The causes of water seepage on the bathroom floor are:

The ground tile gap is not treated tightly;

The connection of the water inlet joint of the toilet squatting toilet is not tight;

There is a gap between the floor drain and the sewage pipe;

There is no spatial separation between the shower area and the washing area of the bathroom, and there is no water barrier in the floor tile area;

Cracked pipes in the wall or leaking tee joints.

What is the cause of water seepage on the bathroom floor?

Kiss. Hello. I'd like to ask what's going on with the water on the floor of my bathroom.

Recently discovered.

The reasons for water seepage on the floor of the bathroom are: the gap between the floor tiles is not treated tightly; The connection of the water inlet joint of the toilet squatting toilet is not tight; There is a gap between the floor drain and the sewage pipe; There is no spatial separation between the shower area and the washing area of the bathroom, and there is no water barrier in the floor tile area; The pipe in the wall of the rolling shed is cracked or the tee joint is leaking.

Water seeps up the joints of the bathroom floor tiles.

There is always a lump of water on the ground.

It's a broken water pipe.

There is also a little bit of water on the walls.

I've seen the water pipes.

The water pipes are buried in the walls, and they flow slowly through the walls before they come out.

I have an experience to share, because there was a situation at home, the bathroom floor was not seeping downward, but seeping upward, at that time my father was also worried because of this problem, but it was finally solved, here are our solution steps:

1. First go to the property for repair, the property owner will naturally claim that this is the responsibility of the owner's decoration, but at the same time he will also give a solution, such asIt is necessary to smash the floor tiles of the bathroom, check whether the waterway pipes and sewer pipes laid below are broken, etc

Water seeps from the bathroom floor.

2. According to the idea provided by the property, since it is upward seepage, not downward seepage, it means that there is no problem with the waterproofing of the homeIt may be that the waterway pipes laid under the floor tiles are leaking water outward

Toilet drain rubber rings.

3. Of course, even if it is suspected that the pipes under the bathroom floor are broken, it is impossible to smash the floor tiles at every turn to check, so we used the elimination method at that timeStart by looking at the toilets that are easiest to remove

Toilet bowl bottom disposal.

4. The result was lucky, and after a dismantling, it was found that it was due to years of useThe built-in sealing rubber ring of the toilet bowl in its drain is broken, so that when it is flushed, part of the water goes into the sewer (which communicates with the mop pool and sink sewers), while the other part seeps into the ground from the side. At the same time, because the waterproofing is done well, this part of the water did not seep down, but seeped up from a gap in a floor tile far away from the toilet.

Toilet drains.

5. The solution is to change the rubber ring and beat the gap again with glue. Of course, according to the above ideas, if it is not a problem with the toilet, then it is recommended to check the sewer pipe of the basin, because it is relatively simple to smash the floor tiles, and even if it is smashed, it is also a piece under the basin, which is easy to cover and clean up. And so on, if you can't do it, you can only smash all the floor tiles in the bathroom, good luck!

The main reason is that it is not waterproof.

It was caused by a waterproof not doing a good job.

1. Water seepage on the wall caused by pipeline leakage. Water seepage on the wall caused by leaking pipes is a relatively common cause. You can look at the construction drawings and check the direction of the water pipes at home.

If there is a water pipe at the location of the water leak. But it is clear that I have turned off the sluice gate when I go out for a long time. However, when water traces were found on the wall for a period of time, it turned out to be a problem with the water pipes.

2. Water leakage of the waterproof layer leads to water seepage on the wall. After showering, water leaks from the back wall of the bathroom. After a while, it was found that the leakage on the wall surface had improved. This proves that there is a problem with the waterproofing layer. Then you need to redo the waterproofing layer.

3. Water leakage caused by improper paint. In a paint project, when the wall is painted with a loss of ears, the first time the wall paint does not dry out, it starts to paint the wall paint for the next time. The water vapor on the wall cannot evaporate, resulting in dampness of the wall.

4. The use of non-insulating materials causes water leakage. In the past, many houses were sold without insulation on the walls. In winter, there is a large temperature difference between the inside and outside.

Therefore, the walls are hot and cold. The walls are hot, so condensation forms on the walls, causing the walls to be damp. In the face of this wall, this situation generally only occurs in winter, and it will be good in summer, but the sequelae is that it will leave a lot of unsightly mildew, which will affect the appearance of the wall.

Once water seepage is found, it must be solved as soon as possible, otherwise it will become more and more serious, which can be said to be a very harmful thing. If you don't deal with it, then after a long time, you will find that even the tiles on the wall will start to fall off, then it will be even worse, so you need to detect and deal with it early.

The problem of water leakage on the bathroom wall, and the problem of water leakage, may be that the pipe is broken, so there will be such a water leakage problem, which is a very troublesome thing.