What should I do if the toilet flush is not clean, what should I do if the toilet is not clean?

Reason 1: The flange interface is installed when it is biased, and the sewer flow rate is reduced.

Solution: 1. When buying a toilet: it must be noted that the water pipes from the general water tank to the tile are about 30 35cm, and their diameters are 110cm.

2. When installing the toilet: to supervise the whole process, be sure to determine the installation location and method, otherwise there will be problems in the follow-up, and it will be dismantled and reinstalled.

3. After installing the toilet: do not test the water immediately, if you test the water immediately, the cement at the bottom will be washed away, causing the toilet to be unstable and leaking from the bottom. Do not use it right away, because the bottom cement is not dry.

Reason 2: The toilet itself does not have enough pumping power and insufficient water pressure.

Four tricks teach you to change the dilemma of slow flushing of the toilet drain.

Solution: 1. You can increase the amount of water, such as putting bottles in the water tank.

2. Adjust the screw of the water inlet valve clockwise to let the water level rise, and pay attention to the water at least 10mm away from the overflow nozzle of the drain valve.

3. Adjust the water level of the water tank appropriately. If it is a slow flow from the water tank to the toilet, check whether there is something blocked from the toilet tank to the flushing outlet.

Reason 3: Insufficient flushing water, water outages and other problems.

Solution: 1. If the amount of water is insufficient, you can take off the lid of the water tank and adjust the amount of water. There are two plastic rods under the toilet water button, and there are cocks on them to adjust the length of the plastic rods to control the amount of water.

2. If it still doesn't work, you can only change the toilet, you can choose the siphon toilet, the effect is good.

Reason 4: Long-term use has caused the sewer pipe to be contaminated with dirt, resulting in a smaller sewer.

Solution: You can remove the sewer pipe, put it into the acidic substance, eliminate the accumulated dirt, and then install it, and the sewer will be much faster. If there is a soft object blocked, you can use a soft spiral pass, or kick it with a toilet, if it is a hard object, it is best to find a professional company to solve it.

The toilet has been used for a long time, and some of the water will be weak and cannot be flushed, so try it to see if it is because the water is too little and cause weakness, you can manually add water to the toilet tank, drain the water to see, if the strength is OK, adjust the tank accessories or replace the accessories.

The toilet flush is generally divided into the following situations: x0d x0a 1. Slight blockage of the toilet: It is generally caused by toilet paper or sanitary napkins, towel rags, etc., which can be dredged directly by using a pipe dredging machine or simple dredging tools.

Toilet Toilet x0D x0A 2. Toilet hard object blockage: When using, accidentally fall into plastic brushes, bottle caps, soap, combs and other hard objects. This kind of blockage is mild, you can directly use a pipe dredging machine or a simple dredging device to dredge directly, and when it is serious, you must disassemble the toilet to dredge, and this situation can only be completely solved by getting things out.

X0D X0A 3, toilet aging blockage: the toilet has been used for a long time, it is inevitable that it will scale on the inner wall, and in serious cases, it will block the air outlet hole of the toilet bowl and cause the toilet to drain slowly, the solution is: find the ventilation hole and scrape the dirt to make the toilet drain unblocked.

X0D X0A 4. Toilet installation errors: generally divided into: the outlet at the bottom is not aligned with the drain, the screw hole at the bottom of the toilet is completely sealed, which will cause the toilet drain to be unblocked, and the water level of the toilet tank is not high enough to affect the flushing effect.

X0D X0A 5, squatting pit to toilet: some old houses are installed when building a squatting pit, the bottom of the sewer pipe is used U-shaped waterproof elbow, when recreating the toilet, it is best to replace the bottom elbow with a direct bend, if you can't change it, then you must do a good job of cleaning up the bottom bend before installing the toilet, and the installation is to avoid letting cement or tile fragments fall in. This kind of squatting toilet should be used with more care.

x0d x0a 3, decoration caused by sewer blockage: this is the most likely to occur in house decoration, we have met a lot of cases of sewer blockage caused by carelessness during decoration, this is definitely not accidental, so we must do a good job of protective measures before decoration. This blockage is generally caused by cement blocks, tile fragments, sediment, paint, woven bags, etc.

If it is a soft object such as a woven bag, you can use a dredge machine to dredge it directly, if it is blocked by a hard object such as cement slag, then you need a professional dredging tool to dredge it.

1. The flushing caused by slight blockage is not clean: sometimes we will choose to pour the paper and leftovers into the toilet bowl and use the flush force of the toilet bowl to flush it away at one time. If this is the case, it is advisable to use a toilet unclogging tool.

2. Dirt caused by unclean flushing: sometimes when our toilet is used too much, it will produce a lot of dirt, which is difficult to clean, at this time we have to use our toilet cleaner, and pour the cleaner into the water tank.

3. The soap is not clean: sometimes the soap is washed off and enters the toilet, and we use hot water to melt the soap.

4. The flushing caused by the toilet shifter is not clean: the toilet is not directly facing the sewer pipe, if it is because it is not installed at the beginning of the installation, it needs to be repaired by the maintenance personnel.

5. The flushing caused by insufficient horsepower is not clean: sometimes we can see that when we press the toilet to flush the shirt, there is not enough horsepower to go down, so we keep pressing the flush button to increase the horsepower.

6. There is also a kind of time when you yourself are because the previous person did not flush the toilet after using it, and has been flushing the toilet, at this time, you should pay attention to the fact that the use of the punch will lead to the lack of punch in the back, at this time, use a tool to dredge it, and then press the button after a while.

7. The flushing caused by aging is not clean: after using it for too long, because of the aging of the toilet, there is a lot of hard dirt in the channel below, which is inconvenient to go into the water and easy to block the water.

The above problems are very common, I hope you can understand the above knowledge, you can try the above methods when you encounter these problems, basically can be solved, if you still can't solve it, it means that the problem is more serious, you need to ask professional maintenance personnel to deal with it.

There are several reasons for this:

1. Weak flushing caused by clogged toilets. Dredging with a dredger, or find a longer plastic water pipe, connect tap water at one end, plug the toilet mouth at the other end, and then block the toilet mouth with something like rags, and then turn on the tap water, which will use water pressure to dredge the pipe, and when the problem is serious, the toilet should be disassembled and dredged.

2. There is too much dirt in the toilet, and the ceramic is dirty, and the flushing is weak due to not being sorted out in time. It can be cleaned with baking soda powder or white vinegar, and it is not recommended to use steel wool balls and decontamination powder, etc., which will damage the ceramic glaze.

3. The water level of the inlet valve is low, resulting in weak water outlet. Remove the inlet valve and remove the inlet valve buckle. Then roll the inlet valve body counterclockwise, adjust the height of the body accordingly, and then rotate the inlet valve body clockwise to install the buckle.

Finally, the inlet valve is installed, and the filter and inlet pipe are connected to eliminate the fault.

4. If it is a side-pressed toilet, it is possible that the chain of the side handle is long, and although the water-stopping pad has action, it will stop the water quickly, and then cause the flushing to be weak, so you only need to shorten the chain to a suitable one.

5. If it is a top-press toilet, the top-press lever is low, which will also lead to a lack of flushing. Open the lid of the water tank and reverse it, loosen the nut of the pressure rod, and adjust the length of the pressure bar to the appropriate level.

I believe that many people have had the problem of the toilet not flushing clean in the process of using the toilet, which is very embarrassing, so only by finding the reason can we "prescribe the right medicine", so what is the problem of the toilet not flushing clean? If you want to know more, you may wish to take a look with us!

1. What's going on with the toilet not flushing clean.

Because the interface of the toilet is deviated during installation, the flow of water from the toilet is reduced; It may also be because the toilet does not flush clean due to insufficient flushing water or insufficient pumping power and water pressure of the toilet itself; It is also possible that due to long-term use of the toilet, the sewer pipe will be stained with dirt, resulting in the sewer becoming smaller and the toilet cannot be flushed cleanly.

Second, how to deal with the smell of foreign fiber in the bathroom.

1. Toilet cleaning should be used as a dredging agent.

You can use the toilet cleaner to clean and disinfect, pour an appropriate amount of toilet cleaner into the toilet every few days, and close the toilet lid to let him suffocate for a while, and then open the lid to wash and flush, which can not only maintain the patency of the toilet, but also remove odors and bacteria.

2. How to block the overflow of floor drains.

First find a plastic bag, the diameter of the plastic bag should be slightly larger than the floor drain, and then fill it with an appropriate amount of water, remove the grate on the floor drain, and put the plastic containing water on the smelly floor drain. Due to the use of water pressure, the plastic bag will be in close contact with the leaky pipe, so as to achieve the purpose of isolating odor.

3. Put balsamic vinegar in the bathroom.

You can place a glass of balsamic vinegar in the bathroom to eliminate odors, and change the balsamic vinegar every other week, which is easy and convenient.

4. Deodorize with tea leaves.

Do not throw away the tea leaves that have been drunk, dry these residual tea leaves and put them in the bathroom, which can effectively remove the odor.

Summary: The above is for everyone to share what is going on with the toilet flushing is not clean and how to deal with the smell in the bathroom, I believe that after reading the above sharing, you also have a corresponding understanding, if you need to know more about it, please continue to pay attention to Qeeka Home**, will answer for you one by one.

<> is generally due to the installation deviation caused by the mistake of the toilet connector during installation, resulting in less water discharge in the toilet. Or the toilet flushing is insufficient, the toilet pumping power and water pressure are insufficient, and the inside of the water pipe is covered with dirt and damage, etc., which may lead to the toilet flushing not being clean.