What should I do if I can t turn on my computer after win10 turns on ahci win10 installation of the

What should I do if I can't turn on AHCI in win10? SSD win10 computer can not turn on AHCI, and finally found that it is mainly due to the incompatibility of the SSD driver, the solution is to update the SSD driver, the specific method is as follows.

1. Restart the computer, when turning on the computer, press F8 to enter the boot settings, and then press the number on the keyboard to select to enter the "Boot Safe Mode with Network Connection", as shown in the figure below.

2、Then it will enter a startup with network connection win10 security mode,In this interface can still be networked,At this time, we install driver detection and installation software in the computer,Such as the familiar driver wizard、Master Lu can。

3. For example, install the driver wizard software, then open it, and then detect the hardware driver, and then generally see that the SSD will have available driver updates, **Install the update driver.

4. After the driver update is completed, you can also go to the device manager to check whether the SSD drive is normal.

Wait for the SSD driver to be installed, restart the computer, and then enter the system normally, you can successfully enter the win10 desktop.

Do you have a cloning system installed? Normally, most of the drivers will be there.,You can keep pressing F8 when you boot up.,Enter Winre to fix it.。

If your computer slows down, the first thing that comes to mind is to install an SSD in your computer. However, recently, a user installed an SSD in the Win10 system and turned on AHCI, only to find that the computer suddenly could not turn on. What should I do?

Below, we will share the solution to the problem that the solid state drive cannot be turned on after installing the solid state drive in the windows10 system and turning on ahci.

Here's how:

1. The reason why it can't be turned on normally is that there is no corresponding driver after changing to ahci, which is equivalent to not being able to read the hard disk. Please follow my operation,Win10 system has a security mode with network driver,Seize the opportunity when you turn on the computer,Press the F8 key to enter the interface in the figure。

2. Press the number key 5 to enter the safe mode with network connection, and after entering the system, you will be surprised to find that its resolution is so low that it is low, which is normal, it doesn't matter. Next, we need to install the driver wizard.

3. The file location can be changed when the driver wizard is installed, and other antivirus software can be unchecked to quickly enter the next step, as shown in the figure. The home page of this software is to detect the computer driver.,Click on it and wait slowly.,At this time, you can find a problematic driver.,Install it.。

4. Don't worry after the driver is successfully installed, let's check whether the driver has been installed successfully, right-click on my computer, click Manage to enter the computer management.

5. The last step, click Device Manager, find the disk drive, check the driver, it is obvious that the SSD has been successfully read, at this time the system can boot normally, restart it.

The above is the solution to the problem that the Windows 10 system installs the SSD and turns on the AHCI after it can't be turned on. Installing an SSD in your computer is one of the most common ways we can solve the problem of slow running computers. Users who encounter the same problem can follow the methods to do it!

How to set it up:

1. The motherboard is the Phoenix BIOS to set the hard disk mode

Power on"del"button to enter the BIOS, use the right arrow key to select the "Advanced" item, after entering this menu, find the "SATA Controller Mode" option (as shown in Figure 1), switch to this item by pressing the down arrow key, press the "Enter" key, and a dialog box will pop up, you can change the hard disk mode, such as setting"ahci", select it with the arrow keys, and press enter. Press F10 to save the exit BIOS when you're done.

2. The motherboard is the method of setting the hard disk working mode of the award BIOS

Power on"del"key to enter the BIOS and find it"integrated peripherals"(Integrate Peripherals), select this item with the arrow key, press Enter (Enter key), open this item, and find "Onchip SATA Controller.""and set to "enabled."", and then find "onchip sata type.""There are three options in this item: "Native IDE Raid Ahci.""Select "ahci" and use "page up" on the keyboard to change the value"page down"key, and when the modification is complete, press"f10"Save the exit BIOS.

Note: Some motherboards set the hard disk mode item to "SATA mode", and the method of changing the value is the same).

3. The motherboard is the UEFI interface to set the hard disk working mode

Power on"del"key to enter the BIOS and find it"Integrated peripherals", check this with the arrow keys and find "SATA mode selection."", press Enter, and set to "ahci". After the modification is complete, save the exit BIOS.

The following describes how to diagnose the failure to boot the operating system.

First, check to see if the computer has started booting up the operating system when you turn it on. If the operating system freezes, blue-screens, or automatically restarts when the operating system is booted, the partition table and master boot record of the hard disk are normal, and the fault causes such as the corruption of the hard disk partition table, the corruption of the master boot record of the hard disk, and the loss of the hard disk partition end flag are ruled out. The following method is then used to make a diagnosis.

Step 1: Start the computer in safe mode to see if it can boot, if it can't boot, it may be infected with a virus, system files are missing, the operating system is damaged, the hard disk has bad sectors, the hardware device has a conflict or the hardware has a problem, go to step 4; If you are able to start Safe Mode, it may be caused by the hardware driver being incompatible with the system, the operating system is faulty, or it is infected with a virus.

Step 2: Then run the antivirus software, if there is a virus, it may be caused by a virus, restart the computer after the antivirus, if it is not normal, you need to reinstall the operating system.

Step 3: If no virus is detected, you can use the "System Restore" function of the operating system to restore the system, and if the system is normal after the restore, the failure is caused by system corruption. If the fault persists, it may be caused by the incompatibility of the device driver with the system; Then delete the drivers of the sound card, graphics card, network card and other devices, and then install the drivers one by one, restart the computer every time you install a device, to check which device's driver caused the failure, find out, ** the new version of the driver of the faulty device, and then install it.

It is true that in some motherboards and the BIOS of this laptop, SATA controller mode only supports AHCI mode, not IDE mode.

In this case, the common ghost system disk is not convenient to use, and it is recommended to use the unmodified original system disk released by Microsoft, that is, the pure version of the system disk. This kind of disk natively integrates the AHCI driver, which can complete the installation of the system smoothly and cleanly.

What's more, if you turn on AHCI, the hard drive performance will be better, and there will be no harm in it.

How to set SATA hard disk to AHCI mode after installing Windows 10.

Step 1: Set Windows 10 to boot into installation mode.

Steps: Right-click [Start] in the lower left corner of the system desktop, click [Command Prompt (Administrator)" in the Start menu, and copy: bcdedit

setdefault}

bootmenupolicy

legacy

command, click the right field in the administrator command prompt window to copy the command to the window;

When bcdedit

setdefault}

bootmenupolicy

After the legacy copy is completed, press the Enter key on the keyboard, and the following message will be displayed: The operation has been successfully completed;

Click the small box in the upper left corner of the window, and click Close in the drop-down menu to exit the administrator command prompt.

Step 2: Enable the AHCI working mode of SATA hard drive in the Scrambled BIOS.

Restart the computer, press the function key F8 on the keyboard to detect whether it can enter the installation mode, if it can enter the installation mode, we restart the computer again, and press the function keys on the keyboard that can enter the BIOS, such as F1, slow Zheng F2, F12, del key, etc., to enter the BIOS;

Mine is to press f12 to enter please

select

BootDevice window, move to Enter

setup, press Enter;

Click: deutsch (German);

In the language selection box that opens, we select [Chinese Simplified] and press enter;

When the BIOS interface is displayed in Chinese Simplified, click [Integrated Peripherals];

Don't tell me it's an IDE when you load it (4K is out of alignment!). I'm all GPT partitions.,UEFI starts),I don't know if you still have a ghost version! Since it's already like this, change it back to the original first.,Soft and then look at the same thing here.,It's okay to open it again.。