Antiseptic wood, how to apply wood oil, what tool is better to brush with?

There is a special painting, you go to the market to take a look...

Anticorrosive wood brush paint method:

1. The processing must be carried out at a temperature of more than 8.

2. The wood must be dry, and the maximum moisture content shall not exceed 15%.

3. Before applying wood wax oil, sand the surface of the wood smooth with a fine sanding cloth and clean the surface to make it smooth. If there are fibers on the surface of the wood, it can be gently sanded with wood sandpaper of P240 or above.

4. Stir well before use, no need to dilute, if the product viscosity is high, you can also add a small amount of special diluent, and the amount added should not exceed 10%.

5. Brush paint with a soft brown brush, uniform along the direction of the wood grain, and then brush a thin brush, after brushing to remove excess wood wax oil, paint must be less, do not paint too thick, to dry the surface, gently polish the paint, wipe clean, 12 children can brush again.

6. Before wiping, soak the dust-free cloth evenly and squeeze too much wax oil into one part; The wiping force should be even, not too heavy or too light, first use a smooth surface paint several times, and finally wipe evenly along the direction of the wood grain to complete, so that the wood grain wax oil fully penetrates into the wood grain and stands; Once the surface is dry, gently sand the surface of the coating, wipe it clean, and follow the steps above.

Precautions for the construction of anticorrosive wood paint:

1. At the construction site, the wooden side must be stacked in a gap of 10-12 mm per layer and protected from rain or direct sunlight.

2. In the construction, the existing size of the anticorrosive wood can be used, such as cutting, drilling, etc., and the preservative must be used to brush and repair to ensure the integrity of the anticorrosive layer.

3. Pre-drilling should be carried out at the joint to reduce cracks.

4. All connections must use hot-dip galvanized fasteners or stainless steel hardware to prevent corrosion.

5. Build a platform and plank road, and try to use long planks to reduce the beauty of the joints. There should be a gap of 3-7 mm between the plates.

6. The adhesive for anticorrosive wood should be waterproof and weather-resistant.

7. Outdoor construction should do a good job of maintenance, such as brushing wood oil, to avoid cracking and deformation of wood caused by sun and rain.

8. When painting, water-based anti-ultraviolet paint must be used, and the wet wood surface should not be painted.

9. The thickness of the wood is greater than 35mm, in order to prevent its deformation, a small cao with a width and a depth of about 10mm can be opened in the center line of the core side.

10. Different grades of anticorrosive wood should be used in different use environments (such as ground, underground or water) to ensure that the design service life is reached.

Content from user: Andy.

Anticorrosive wood paint application steps.

How much do you know about preservative wood? If you have antiseptic wood in the panels of your house, how do you paint them? Below, we will answer the two questions of the construction steps of anticorrosive wood paint and how to paint anticorrosive wood.

Anticorrosive wood paint application steps.

First, the construction site, the stacking of wood must be 10-12mm gap in each layer, but also to prevent rain or direct sunlight.

2. During construction, it is possible to use the existing size of anticorrosive wood, and if it is necessary to cut, drill, etc., it is necessary to use preservatives for brushing and remediation to ensure the integrity of the anticorrosive layer.

3. Holes should be drilled in advance when connecting to reduce cracking.

4. All connections must use hot-dip galvanized fasteners or stainless steel hardware to prevent corrosion.

Fifth, build terraces and plank roads as much as possible to use long planks to reduce joints, in order to be beautiful. There should be a gap of 3-7mm between the plate surfaces.

6. The adhesive used in anticorrosive wood should be waterproof and weather-resistant.

7. After the completion of outdoor construction, maintenance work should be done, such as brushing wood oil, etc., to avoid the occurrence of wood cracking and deformation caused by sun and rain.

8. If you want to paint, you must choose outdoor weather-resistant wood paint, and the wet wood surface should not be painted.

9. For wood with a thickness greater than 35mm, in order to prevent its deformation, a small groove with a width and depth of about 10mm can be opened in the center line of one side of the wood core.

10. Different grades of antiseptic wood should be used in different use environments (such as on the ground, under or in the water) to ensure that the design service life is reached. 6.Before wiping, soak the dust-free cloth evenly and squeeze out part of the excess wax oil; When wiping, the force should be even, not too heavy or too light, first along the surface of the coated object alternately horizontal and vertical rubbing several times, and finally the end of the wood.

First of all, the wood is sanded clean and tidy, the wood wax oil is stirred evenly, and the first time is thinly rubbed, and after drying, the second time is thinly rubbed. If the requirements are relatively high, after the first time to do dry with polishing cotton lightly, in the brush for the second time, the last time can be sprayed, but it is more costly, but there is no scratch, the effect is better, if the requirements are not so high, just wipe it directly, it is recommended to brush 2-3 times, and it is recommended to consult professionals for specific construction. --Cheresi wood wax oil replied.

Polish, then brush twice.

1. Wood preservative can be made with cooked tung oil, wood oil and wood wax oil.

2. Cooked tung oil: tung oil is a kind of vegetable oil with dryness, which has the characteristics of anti-corrosion, anti-rust and non-conductive.

3. Wood oil: It has excellent penetration and adhesion, and will form a protective coating that can resist ultraviolet radiation in the sun.

4. Wood wax oil: The oil of wood wax oil can penetrate into the wood and give the wood deep moisturizing and maintenance.

Take anticorrosive wood as an example, tool: wood with cooked tung oil, the steps are as follows:

1.Substrate treatment.

The substrate is generally sanded with 100 sandpaper until it is smooth and flat. And remove the sanding dust to confirm that the surface to be coated is clean, dry and free of grease and dust.

2.Brushing. It can be wiped, brushed, sprayed, and evenly brushed along the direction of the wood grain when brushing, paying attention to thin coating.

3.Polished. After the surface of the wood is dry, use more than 600 polishing cotton or sandpaper to lightly polish the surface layer, and clean the surface sanding dust to enhance the feel.

4.Second coating. After the surface of the wood is finished, please follow the method of the first coat and recoat it for the second pass.

5.Polished. After all the construction steps are completed, the surface is dry, and the surface layer is slightly polished with more than 600 polishing cotton or sandpaper, and the surface is cleaned to improve the feel.

6.Acceptance. After the surface of the brush is dry, clean it with a cotton cloth. If the gloss of the hand does not meet the requirements, you can apply it for the third time.

After brushing tung oil, the wood needs to be left for a few days to dry, during which the smell is larger, and the smell can be removed by opening the window for ventilation, placing green plants, activated carbon, etc.

How to apply tung oil.

There are generally two methods of brushing tung oil, one is to wrap a ball of cotton with a white cotton cloth or soft muslin, twist it into a cloth ball, or use nylon silk balls. The size of the cloth ball is determined according to the size of the rubbed area, and the bottom is flattened after wrapping. You can also choose a bristle brush with thin bristles and good elasticity.

The temperature of the construction site is required to be above 15 degrees, and the relative humidity is about 65%. If the construction temperature is not enough, the surface can also be preheated by artificial heating, which can accelerate the surface drying speed. During indoor painting construction, doors and windows should be closed, and blowing on the surface of the coating should be avoided as much as possible during the painting process, so as to maintain the indoor temperature balance.

If the construction is carried out outdoors, it should be carried out in a sunny weather with no wind and sufficient sunlight.

Here's how to do it:

For the first time, first use a cotton ball dipped in an appropriate amount of tung oil, and first rub it on the surface along the wood grain several times. The loop coating method is then applied on the same surface, that is, the cotton ball is rubbed on the surface in a circular motion. There should be a certain regularity in the circle coating, and the cotton ball moves at a uniform speed in the direction of the wood grain while rotating on the surface.

Rub from one end of the surface to the other. In the process of rubbing, the size of the circle should be consistent, and the entire surface should be continuously rubbed from head to tail. After rubbing the entire surface in circles of the same size several times, the diameter of the circle can be increased, from small, medium to large.

The movement trajectory of the cotton ball can be carried out in three ways: circle coating, figure 8 coating, and straight line coating. The ring coating method thickens the coating and pushes tung oil into all the recesses on the surface and into the holes of the wood pipes. The curvilinear motion of the cotton ball can also be presented in the form of waves, zigzags and other smooth and continuous curves.

According to a variety of curves, each wipe, can form a smooth and uniform and very thin coating, but after continuous rubbing with the curve shape for many times, may leave traces of coating, at this time, it is generally necessary to use horizontal rubbing, oblique rubbing several times, and then the method of wiping straight along the wood grain, in order to wipe out the oil film flat, and eliminate the curve trajectory, in this way, you can end the first rubbing.

The second rubbing After the first rubbing of the wood surface, after two to three hours of drying, the basic method of the rubbing process is the same as the previous one. The number of times of the second rubbing can be reduced, and at the same time, the amount of cotton balls dipped in tung oil is also less than the first pass, but the force is heavier than the first pass, and the time of wiping is shorter than the first pass. The purpose is to fill in the subtle irregularities of the seepage, and generally after several times of circle coating, it is then rubbed along the wood grain.

When a certain thickness is reached, the second coating can be completed after the oil film is smoothed.

After the second wipe and coating, it should also be allowed to dry for 2-3 days to obtain a smooth and smooth oil film with high gloss.

Regular antiseptic wood does not need to be brushed with tung oil, brush wood oil to prevent wood from cracking, and sunscreen is enough

The anticorrosive wood is generally brushed with wood wax oil, and the effect is good.

I do outdoor garden materials, first of all, I must brush, if it is a general project and the wood is a dry material, you can only brush water-based varnish; If it is a wet material and a real estate company project, it is recommended to use a partition to separate each layer Ventilation and drying in the sun for a period of time (air drying, remember to cover in the rain) on the primer water-based varnish + one side of the dark wood wax oil It is recommended not to take too many anticorrosive wood projects It is best to recommend that Party A use pineapple lattice Although it is a ** problem, there are too many problems with anticorrosive wood

Anticorrosive wood is usually used outdoors, and wood paint should be used for painting, because the weather resistance of polyester paint is not good, and polyester paint should not be used in places with strong ultraviolet rays, which are easy to peel and peel.

The main function of wood oil and wood paint for anticorrosive wood is to decorate the surface of anticorrosive wood and change the roughness, gloss and color of the wood surface.

Wood oil and wood paint for anticorrosive wood are different from ordinary paints, they have high weather resistance, and they are not easy to shell and peel when placed outdoors. Both wood oil and wood paint can penetrate into the interior of the wood, effectively restricting and sealing the entry and exit of moisture in the wood, and preventing the wood from drying out and shrinking due to changes in external moisture. Ordinary wood oil is fully permeable to anticorrosive wood, and common wood paint is semi-permeable to preservative wood.

Hello, you need to brush a layer of water-based wood oil. This prevents the sheet from rotting quickly, a protective film.

Top 100 water-based wood oil A barrel can be brushed about 10 square meters, and it can be brushed once a season.

Preservative wood is wood treated with preservatives, and it doesn't matter whether it is used or not.