Can the iPhone11pro mobile phone screen be repaired if there are some tiny failures?

If it can be repaired, you can try to repair it yourself first.

Screen water ingress failure solution:

What should I do if the screen of Apple iPhone 11 phone is out of order? Is it scrapped and unusable? In fact, the water on the screen of the Apple iPhone does not mean that it is scrapped, you can try the following methods to see if it can be restored.

Method 1: Use a hair dryer to blow on the air.

When the screen of the Apple iPhone 11 phone fails in water, do not try to turn it on, but let the phone continue to be taken out of the water, and then use a hair dryer to dry it as soon as possible. After the surface is dry, continue to blow along the gap or jack of the mobile phone to ensure that the dry position is completely done.

Method 2: Dry with an electric heater.

If the problem cannot be solved after using a hair dryer, then it is necessary to use an electric heating treasure.

Prepare two dry towels with good water absorption, wrap the phone with a towel, wrap at least three layers, and then use an electric heating treasure to dry, so that all the water hidden in the phone will seep out, and the problem of the mobile phone entering the water screen can be solved.

Method 3: Send it for repair.

Many screen failures are caused by hardware failures, and if the first two methods cannot be solved, they can only be sent to after-sales maintenance.

In addition, after the screen of the Apple iPhone mobile phone is flooded, special attention should be paid to the following points:

Don't shake the phone back and forth: After scooping the phone out of the water, remember not to shake the phone back and forth, this action will cause the water to spread quickly inside the phone, causing more unnecessary damage to the phone.

Don't force it on: Under normal circumstances, the internal motherboard of the fuselage is equipped with power protection after the mobile phone enters the water, and the mobile phone is in a shutdown state at this time.

Do not use the hot air function of the hair dryer: the conductivity of the water and the high temperature of the hot air may cause the battery interface to leak or the internal circuit to short-circuit and burn the phone.

What kind of failure is it? Is it a bit out of control? If yes, you can turn off and restart it, I occasionally encounter the screen uncontrolled, I don't know if there is a virus, I will be fine as soon as I restart it, I don't know why.

Fault Problems and Solutions of iPhone 11 Screen Touch Failure:

Solution: Force restart, press the volume up button once, then press the volume down button again, and then press and hold the power button until the apple icon appears and then let go.

2. Short circuit in the screen cable or touch layer.

Solution: Repair the touch by pressing and replacing the touch layer, if it is seriously damaged, you can only replace the entire screen.

3. Short circuit solution for motherboard touch chip, touch connector, CPU, and board layer: Since iPhone11 is also a double-layer motherboard, it needs to be repaired by heating layering, and then repairing the chip by repairing the chip, replanting, and flying wires.

1. Check whether the mobile phone has a film, if there is a suggestion to cancel the screen film, try it.

2. It may be that there is an electrostatic phenomenon caused by conductive media such as oil stains and sweat on the mobile phone screen, use a rag to wipe the screen and try it.

4. Open the iTunes software on the computer and upgrade the system version of the mobile phone.

5. If the screen fails due to hardware damage, please go to Apple's after-sales service center to seek a professional solution.

Hello, I'm Mai Ruizi, welcome to use the know app, I will answer for you, I am honored to serve you, I will take your questions seriously and carefully, typing and sorting out the information may take a few minutes, please be patient!

Dear, iPhone11 screen touch failure fault problem and solution: 1. Apple iOS system conflicts with the installed APP and causes the system to freeze Solution: Force restart, press the volume up button, then press the volume down button, and then press and hold the power button until the Apple icon appears and let go.

2. Short circuit solution for screen cable or touch layer: repair the touch by pressing the row and replacing the touch layer, if it is seriously damaged, only the whole screen can be replaced.

I hope mine can help you, and if you are satisfied, you can give a thumbs up and kiss [Bixin].

Apple mobile phone screen failure is usually a failure of the mobile phone hardware or system failure, you can restore the mobile phone to factory settings first, if the mobile phone after the factory reset screen failure can not be solved, you can go to the Apple after-sales center to detect whether the hardware of the mobile phone is faulty.

Hello, iPhone 11 phone screen failure causes and solutions.

1. Static electricity causes the screen to temporarily fail in winter, the screen is particularly prone to static electricity, when you put the iphone for a long time is not applicable, just turn on, you will find that the picture is not very sensitive, it is likely to be caused by static electricity. You can use one hand and one hand on the wall or floor with an iPhone. You can wipe the screen, three times in a single palm, you can eliminate static electricity, and then open the lock screen to use it normally.

2. The owner of the system card can or crash due to system jamming or software conflict, and can force restart the phone. Force Restart Method: Step 1:

First, quickly press the "Volume Up" button on the side of the fuselage, and then quickly release it; Step 2: Then quickly press the "Volume Down" button on the side of the fuselage and release it quickly; Step 3: Then press the "Power" button on the other side of your body until the screen is on the screen and release the handle.

In the third step, the screen will first show the power off slider, remember to ignore it, and then continue to press and hold the power button until the whole screen goes black, the Apple logo appears, and the force start is done. 3. How to distinguish the failure caused by a touch IC failure as a disjointed IC fault? Press the part of the phone underneath and the screen will be pressed and then the iPhone taps on the palm of your hand, and if the touch IC is faulty, then after the above operation of the touch screen will not work properly, you can be sure that the IC is a touch screen and not a problem.

Fourth, the screen cable is loose damage or inner screen failureIf you try not to use the above methods, then you can judge that the screen itself is faulty, if the screen has a loose cable, you need to buckle the cable, and the unused cable can only be replaced. The above are the reasons for the failure of the iPhone 11 phone screen and the solutions.

Fault Problems and Solutions of iPhone 11 Screen Touch Failure:

1. Software Failure.

2. Solution: Force restart, press the volume plus button, then press the volume down button, and then press and hold the power button until the apple icon appears.

iPhone 11zero, if the screen is always out of order, you can go to a mobile phone repair shop for repair, so that the mobile phone screen will be fine and will not fail.

I think it may be that the screen is out of order, and I go to the local maintenance point to see it.

What should I do if part of the screen of the Apple 11 mobile phone failsHello dear, 1. The charger used for charging is not original or the adapter is faulty. 2. Static electricity interference is caused by friction of the mobile phone in the pocket. 3. The screen of the mobile phone is wet or wet.

4. The operation of some software of the mobile phone causes the system to respond slowly. 5. The firmware of the mobile phone or the touch screen itself is damaged. Reasons for the failure of the touch screen of the mobile phone screen:

1. The charger used for charging is not original or the adapter is faulty. 2. Rubbing the mobile phone in the pocket produces static interference. 3. The mobile phone screen is wet or wet.

4. The operation of some software on the mobile phone leads to the slow response of the system. 5. The firmware of the mobile phone or the touch screen itself is damaged. Workaround:

1. Replace the original charger of the mobile phone. 2. Press the power button to turn off the screen, and then light up the screen, which can generally return to normal. 3. Wipe the water off the phone screen, and the touch screen will return to normal.

Force restart the phone first, if it still doesn't work, then you can only go to the after-sales service for inspection and repair, good luck!