What are the quick and easy ways to reverse into storage

Right warehousing formula, left and right meters to meters, cover the yellow line to the right full, hit the right rear wheel frame.

1. The speed of the vehicle should be slow, 2. The direction of the dozen should be fast, and 3. Pay attention to the selection of warehousing references.

【Pacific Automobile Network】The driving speed should be controlled during the operation of reversing and warehousing, and the whole process should be idle with 1 gear or reverse gear, and the starting speed and driving should be consistent. In the process of controlling the timing of steering, we should observe carefully, grasp the key points of steering, and turn in a timely manner.

1. Turn around and reverse.

U-turn and reversing should be carried out in places where U-turns are allowed (such as highways, forks, street entrances, etc.), and should be carried out according to the width of the road surface and the specific situation of the vehicle density. When making a U-turn and reversing on a wide road, you can directly judge the position of the rear of the vehicle or the wheels on the road from the reversing mirror. If you can't accurately determine the position of the rear wheel and the rear wheel from the rearview mirror when turning around and reversing on a narrow road, you can open the door and observe the rear wheel while operating.

If you need to go forward and backward many times, you should get out of the car and see the safe distance between the road and the wheels to prevent falling into the ditch. In areas with a high density of vehicles, there should be a person to command. When turning around and reversing at forks and street intersections, it is necessary to appropriately expand the line of sight and range behind the vehicle, timely and accurately judge and grasp the movement of passing vehicles, pedestrians and bicycles, and reverse cautiously to prevent accidents.

2. Garage reversing:

Garage reversing is generally carried out when the vehicle returns to the parking garage or enters the temporary parking lot to park. If the vehicle has a good line of sight (such as light buses, cars, buses, etc.), it can be directly observed from the rear window of the vehicle to reverse. If the reversing line of sight is poor and you can't see the back directly (such as a fully loaded truck, etc.), you should open the door and judge the position of the body in the garage from one side of the door, and pay attention to the other side of the body from the reversing mirror to prevent scratching or scratching other vehicles.

3. Turning and reversing:

When the driver is turning and reversing, he should pay attention to judging the situation on the inside of the turn and the rear of the vehicle, and take into account both sides of the body from the reversing mirror, and pay attention to the timing of turning the steering wheel to prevent traffic accidents that cause rear collisions and body scrapes.

4. Shift and reverse:

Generally, when entering a narrow parking space or meeting a car in a narrow section, it is necessary to move the position left and right to avoid it. In this way, it is sometimes necessary to reverse several times, so it is necessary to pay careful attention to the width of the position where the vehicle is moving, and to judge the position of the rear of the vehicle, both sides of the body and the rear wheels, so as to prevent traffic accidents such as collisions, scratches, and ditch drops. If necessary, someone should be behind the car to command.

Photo by Chen Fang of Pacific Automobile Network1).

The three easiest ways to reverse into storage are as follows:

1. Slotted reversing: drive the car parallel to the front car, 1 meter apart, and start reversing until the rearview mirror on the right side is aligned with the B-pillar of the front car. To the right, the steering wheel is full.

When the car and the side car are at an angle of 45 degrees, hit the left full car and continue to reverse. After entering the parking space, you can return to the right after judging the position of the rear wheel, and the reversing is over.

2. Non-zigzag reversing method: the rear of the car and the front car are in line, meters apart, the steering wheel is full to the right, and start reversing, when you confirm that the front of the car is right, immediately return to the steering wheel, and continue to reverse until it fully enters the parking space. Parking is done.

3. Diagonal parking: the simplest one, the left rearview mirror of the car is aimed at the sideline, and the steering wheel is full to the left to start reversing, and when the body is parallel to the line, it returns to the right. Reverse slowly and smoothly into the garage.

Reversing into storage is the second subject, and it is the difficulty of the second subject exam. Students spend most of their time in the driving school venue to practice reversing into the warehouse, and the test rooms in many places also take reversing into the warehouse as the first test item of subject 2. The secret of reversing into storage is three points:

Steering wheel hit the dead point, 30cm reversing on time, parking point. Reversing is recognised as the most difficult item in subject 2. In the first 4 to 5 days, you can specialize in reversing and warehousing, and learn how to correct the direction when reversing.

The full score of the subject 2 test is 100 points, and if the student is taking a large bus or a large truck, medium-sized bus, city bus, tractor and other quasi-driving driver's license, then it needs to reach 90 points and above to qualify. If you take another type of driver's license, such as a small vehicle license such as C 1, C2, and C3, you only need to achieve a score of 80 or more to qualify.

The easiest way to reverse into storage is as follows:

1. Right reversing warehouse: get on the car to adjust the seat, backrest, adjust the left and right rearview mirrors, adjust the mirror to the lowest, and it is best to be able to see a little rear wheel. Buckle up.

First tow the car to the appropriate position, hang the reverse gear, gently lift the clutch and reverse slowly, when the vehicle runs to the left rearview mirror when the lower edge touches the control line, the steering wheel is killed to the right.

2. Look at the left rearview mirror after hitting the direction to the right, and see the direction of the library corner from the left rearview mirror (if the left front door handle has been pressed to the line, do not turn back to the direction and pour it directly in).

3. After the direction returns to the right, retreat to the left front door when the handle is pressed on the left library line, and then the steering wheel is killed to the right.

4. When you see the left bottom line library angle, the steering wheel is back to the right, wait for the body to be vertically and parallel to adjust the body to reverse into the garage, correct the body and look at the left rearview mirror, when the left rearview mirror shell is pressed on the front edge of the library when stopping.

Reversing is a mandatory item to obtain a small car license after 2013. Examine the driver's ability to operate the car on site. Reversing into storage is an assessment point in the driver's test. That is, to maneuver the vehicle in motion to correctly reverse into the garage from both sides.

There are three most common types of reversing, the first is the "non" type reversing into storage, which is commonly found in various hypermarkets. The second is the "one" shape on the side of the road reversing into storage, which is often referred to as side parking. The third type is the less common diagonal type of reversing storage.

70% of the accompanying students think that it is more difficult to park on the side.

90° reversing into storage.

This reversing method is the same as the subject two exams, first control the distance between the car and the parking space line, and then drive the car to a position parallel to the parking space line, and the rear of the car is in the same straight line with the front of the first car next to it, fill the steering wheel to the left, and then observe the two rearview mirrors to see whether the car is parallel to the parking space line on both sides or the cars on both sides, and the steering wheel is back to the right after parallel, and then move forward and backward according to the length of the tail, and finally park the car.

Oblique warehousing method.

When there is a large space in front of the parking space, find the parking space, and then drive the car to the front, the body and the parking space side line keep about 1 meter, and when the body and the parking space keep 45 °, the steering wheel is reversed, and then the steering wheel is played to the left in a timely manner, until the body is parallel to the parking space line or the vehicles on both sides, and the position can be parked by adjusting the position, this method is simpler than 90 ° reversing into the garage, and also lower than the side parking difficulty, but the disadvantage is that the area in front of the parking space is eaten, and the position of the area is not suitable for this method.

There are three ways to reverse the car into storage:

The first type: parking spaces in the shape of the word "not".

1. Return the car to the right direction, parallel to the parking space line, and the distance from the ground line is about meters.

2. When the car is in the middle of the parking space of the next car, the steering wheel should be killed to the left as soon as possible, start reversing with reverse gear, and use the handlebar to align the marking line on the ground.

3. If you feel that the front of the car is back to the right, you should immediately return to the steering wheel to start reversing, and judge the position of the car with the help of the reversing radar to stop.

The second type: "one" shaped parking space.

Such parking spaces are all over the street, but for new cars, it is still a bit difficult, often in the middle of the road there is not much time and space to roll into, and in most cases only one can be in place.

1. Correct the direction, Min Kai let the car drive to about 50 cm away from the left side of the car in front, and the big ridge can review the original driver's license parking guidelines, and then slowly reverse backwards.

2. When the right rearview mirror of the car is aimed at the B-pillar of the vehicle in front, the steering wheel should be killed to the right (the left side is to the left).

3.When the body and the car in front are at an angle of about 45 degrees, turn the steering wheel to the left and return to the right direction when you enter the parking space.

The third type: diagonal parking space.

Such parking spaces are generally found in places with little traffic, but the parking lot is located in a busy road, which can make parking and storage look the easiest and easier.

1. Choose a parking space first, turn the direction of the car back to the right, let the left mirror aim at the left line of the parking space, and slowly drive forward with the steering wheel to the right.

2. When the body is longitudinally in a straight line with the parking space, stop or quickly return to the right direction.

3. Slowly reversing into the garage is very simple for many old drivers, directly use the door handle to align the parking line, and then reverse in the right direction. But for novices, reversing into storage is always an unfathomable science, and it must be practiced repeatedly.

As follows: reversing into the warehouse is difficult to verify the disadvantages in the highlights and need to pour twice, some candidates reverse into the warehouse after pouring the left library forgot the operation of the right library, after learning the right library and the operation of the left library is confused, in short, there are many reasons for not learning.

The rules of reversing into storage are to divide the test car into the left library and the right library within 210 seconds, and the corresponding car is parked in the specified area, the body line is unqualified, the wheels are not qualified to cross the starting line, and the unqualified is not qualified within the specified time. So next, Xiao Hei will explain to you step by step the reversing and warehousing of subject two.

As shown in the figure above, it is the third perspective, and it is necessary to emphasize a few points before speaking, the first is to wear a pair of comfortable shoes during the test, and the second is to try to step on the clutch and brake before the test, and be familiar with the braking strength and clutch strength of the test car, so that it is easier to control the speed.

The third is to pay attention to adjusting the seat and rearview mirror, if it is different from the usual point of viewing, you must adjust it in time, so as to ensure a smooth test period. The first step is to park the front wheels must exceed the control line, which is actually nothing interesting to pay attention to the body and the solid line parallel.

The picture above is the first point of view, so that everyone can clearly see that the point is **. As shown in the figure, after starting to reverse, stabilize the speed of the car and observe the reversing mirror on the left, observe the area that can be seen in the reversing mirror, and when the reversing mirror is about to reach the starting line or slightly exceed the starting line, quickly hit the steering wheel and kill to the right.

The whole steering wheel is a full three laps from left to right, which is a teasing that everyone must know, because the body is positive at the beginning, so to the right is to hit the right for a circle and a half in the direction, and then stabilize the speed.

The next third step is to observe the so-called 30 centimeters, but this 30 centimeters is different from the 30 centimeters of the side parking, this 30 centimeters is the rear wheel or rear door door handle in the rearview mirror, see the distance from the garage corner is about 30 centimeters when you need to adjust the direction, and at this time you need to turn the steering wheel back to the left, this step is the most likely to make mistakes, so you must pay attention to it.

On the premise of continuing to reverse after returning to the left and right rearview mirrors, when you see from the rearview mirror that the body and the side line are close to parallel or the distance between the side line and the body on both sides of the garage is almost the same, you can return the steering wheel to the right Shanshi date, and then ensure that the speed of the car is slow, and pay attention to the direction of fine adjustment, if the body is right, you do not need to adjust too much.

The last step is the so-called fixed-point parking, when the car is just in the garage, when to brake and stop in the garage for three seconds to complete a reverse warehouse operation, then when is just right.

It is still the best time to observe the rearview mirror, in fact, it is similar to the point of the second step, that is, the rearview mirror coincides with the front edge line of the garage or the rearview mirror crosses the front edge line is the best time to stop.