Does Volvo XC60 burn oil?

Causes of Volvo XC60 oil burn and how to prevent it.

The engine oil itself has a certain amount of consumption, and excessive consumption is the problem of burning engine oil. There are many factors that affect the burning of engine oil, such as: fuel quality, driving conditions, driving habits, maintenance habits, etc., the following reasons will aggravate the oil consumption and cause the burning of engine oil, so that the vehicle appears:

1. Carbon deposition occurs in the combustion chamber, which makes the gas ring of the piston ring stuck, and the sealing is poor.

2. Oil sludge is generated in the lubrication system, and the oil sludge blocks the oil return hole of the oil ring and weakens the oil scraping performance.

3. Wear occurs between the piston and the cylinder wall.

4. The valve seal is corroded and aging, and the sealing performance fails.

In addition, cars now have crankcase ventilation systems (exhaust valves), which can also exacerbate oil consumption if there is a problem.

Burning engine oil means that the engine oil enters the combustion chamber of the engine and participates in the combustion along with the mixture. The phenomenon of "burning engine oil" in the vehicle will damage the vehicle's oxygen sensor too quickly, resulting in an increase in carbon deposition in the combustion chamber, unstable idling, weak acceleration, increased fuel consumption, and excessive exhaust emissions.

Precautionary measures for burning engine oil:

1. Use high-quality engine oil

Engine oil is very easy to corrode and age in a long-term high temperature state, resulting in the oil film becoming thinner, and it is easier to escape to the combustion chamber to participate in combustion, so the use of high-quality engine oil can greatly delay this phenomenon.

2. Pay attention to the cleanliness of the fuel circuit

Fuel in the combustion process is indispensable to produce carbon deposits, and carbon deposits are the root cause of some car failures, such as the aging of valve seals, piston wall clearance, etc., all have a direct or indirect relationship with the formation of carbon deposits, considering the relationship between domestic oil products, it is necessary to use high-quality engine oil and (PNF) fuel additives to achieve, which is also the key to achieve no dismantling and repair to solve the problem of burning engine oil.

Now the fuel consumption is still very satisfied, before were more than 9, may be the driving feeling is also violent, the last time to maintain the imported GT oil, the current XC60 fuel consumption is stable at about that, how much commuting will also be jammed. It is recommended that riders change to a high-end point of full synthesis, the original factory is really average.

Most of the Volvo S60 oil burns because the piston rings are trapped by carbon deposits. Relying on the addition of high-viscosity engine oil to continue life is only an expedient measure to cure the change. When the oil enters the combustion chamber to participate in combustion, more carbon deposits will be formed, which in turn will lead to the aggravation of the burning of engine oil, forming a vicious circle.

In the long run, it will cause cylinder wall strain, or even cylinder burst, and finally the engine can only be disassembled for overhaul.

Four reasons why you burn engine oil.

A ...If you don't clean the oil circuit for a long time or don't do effective oil circuit cleaning, detergents are used at will, and using detergents and effective detergents are two different things;

IIThe antifreeze replacement cycle is too long or not changed at all;

IIIThe oil change interval is too long;

IVLong-term or often short-distance driving.

The above four points of the vehicle that burns engine oil must be occupied by one or all four points.

How the piston rings are stuck.

The principle of piston ring stagnation should start from the oil circuit, the oil temperature is 110 degrees, and the high temperature caused by the long-term unclean oil circuit makes the oil at a temperature of 120 degrees or higher for a long time, so that the oil will be exhausted in advance, the small hole of the oil ring is very small, and the oil inside will be dried and scabbed for a long time. It becomes a liter of engine oil for 1000 kilometers or even hundreds of kilometers. Therefore, in order to solve the problem, we must start from the root oil circuit, which is the way to remove the root.

The solution to burning the oil.

In the habitual thinking of car enthusiasts, they always think that burning engine oil should be overhauled, so that they not only have to bear high maintenance costs, but also bear the unpredictable risks and depreciation losses brought about by the overhaul. Destroy the airtightness and precision of the engine. And there is a possibility that the engine oil will burn again after tens of thousands of kilometers, so overhauling the engine is not sustainable.

Now the no-dismantling technology has been very mature and gradually accepted by the majority of car owners. In particular, the non-destructive repair products containing PNF patented technology have completely gotten rid of the technical shackles of the operation of the auto repair shop, and the owner can operate it himself without removing a screw, and the piston ring is repaired and released during driving, and the effect is remarkable.

If you burn the engine oil, you will generally choose to overhaul it directly, which is more direct, but the cost is high for a long time, and the warranty is not guaranteed. Then the engine is cleaned, and it usually looks like 10,000 to do it once, and it costs a few hundred dollars at a time. Then it's like now, use some high-quality engine oil to reduce engine carbon deposition and protect the engine, I have always used GT engine oil, the oil is of high quality, it will not produce carbon deposition itself, and the high temperature protection is also good, it has been used for more than a year now, and the car performance is better than before.