How to make a lantern is simple and beautiful, how to make a lantern is simple and beautiful

The first step is to make a skeleton. The relatively simple shape of a paper lantern is a cube or cylinder, and it is best to use bamboo branches or bamboo bark that can be bent to form a frame, and tie the joints with thin wires. If you can't find it, you can also use slender strips of cardboard and bamboo skewers for barbecue, which will lack firmness and flexibility, but they are also very good decoration for the interior.

The second step is to make the lamp body. Buy a few pieces of white or red ordinary rice paper or sprinkle gold rice paper at the Four Treasures of the Study, cut them to the length and width of the lantern skeleton, and then you can design your own patterns. Calligraphy, painting, and paper-cutting can all be displayed on a small lantern.

After pasting, you can also use narrow strips of imitation silk paper to edge up and down, which looks more elegant, much like an ancient palace lamp. If you are not very good at calligraphy and painting, there is a simple way to refer to it. Use a piece of tissue paper to trace the desired character on the notebook, then overlap the tissue paper with crimson rice paper, and use a single-edged blade to dig out the handwriting.

When the tissue paper is removed, hollowed-out handwriting appears on the red rice paper. The body of the lamp is made of white rice paper, and the red rice paper is pasted inside, and the candlelight or light is reflected from the hollow, and the effect is quite beautiful. The third step is to make a light source.

If you put it indoors, you only need to light a regular candle in a lantern; If you want to carry it out, it's best to make a simple circuit with a light bulb and a battery.

Simple and good-looking red lanterns, you can make one for a few cents, handmade origami lanterns.

Simple and beautiful lanterns are handmade and can be learned in a minute.

The simple and beautiful lantern recipe is as follows:

Tools Ingredients: 15 red envelopes, 1 pendant, stapler.

In the first step, first fold the red envelope in half along the buried mold between the middle bends, and then fold the four corners along the line after the middle fold, and the other 14 are the same.

In the second step, the 5 corners of the red envelope are stapled with a stapler, and the upper part of the lantern is formed. Take another 5 red envelopes and make the bottom half of the lantern in the same way. At this time, the middle part of the lantern was missing.

In the third step, the middle part of the lantern must be turned horizontally with the remaining 5 red envelopes, which are also tied to the corner and corner of the lantern in the upper part of the stapler booth machine.

Fourth, there is no need to rush to tie the lower part up, at this time, the rope of the pendant should be passed through the hole in the middle of the upper part, otherwise the pendant will not be installed.

In the fifth step, the pendant is finally put on, and the lower and middle parts of the lantern are tied diagonally with a stapler, and a beautiful homemade lantern is completed.

Sixth, if you want to make the lantern more perfect and beautiful, you can make the flat part of the red envelope out with your hands, so that the lantern will become more "reunited".

Here's how to make a lantern:

Material tools: red A4 paper, yellow A4 paper, double-sided tape, ruler, knife, scissors, rope.

1. First cut the red A4 paper from the middle, fold half of it up and down about 1cm, and paste double-sided tape on the folded place.

2. Then use a knife to scratch every 5mm on the red paper, the more precise the stroke, the better, and put it aside for later use.

3. Then cut the yellow paper into a 11cm wide rectangle, paste double-sided tape on one side of the rectangle, and roll it into a barrel.

4. Tear off the double-sided tape on the red paper, align the edge of the red paper with the cylinder, and glue the double-sided tape on the upper and lower sides of the cylinder.

5. Next, cut the remaining red paper into a 5cm rectangle, fold it at the top 1cm, paste double-sided tape, and cut out the lantern spike.

6. Then roll the lantern tassel on the rope, make the top and bottom of the lantern with two 6cm yellow squares, and pass the finished lantern tassel through the bottom of the lantern.

7. Finally, wear the lantern well, glue the bottom of the lantern, and then pass through the top of the lantern, and glue the top well.

The practice of lanterns:

Preparation materials: paper cups, double-sided tape, scissors, wool.

1. First of all, use scissors to cut off the raised circle on the top of the paper cup.

2. Then cut the paper cup into long strips of uniform thickness.

3. Then trim the top of the paper cup and cut out small triangles.

4. Turn the paper cup upside down and flatten.

5. Then prepare a paper cup, cut off the bottom of it, and wrap a circle of double-sided tape.

6. After tearing off the double-sided tape, stick it to the small triangle you just cut, and be sure to stick it firmly.

7. Then cut out a circle of paper cups from the top of the paper cup that just cut off the bottom, and paste double-sided tape on the inside.

8. Tear off the double-sided tape and stick the double-sided tape on the outside of the triangle, which should also be glued firmly.

9. After all is done, gently press down the paper lantern with your hand so that it can be formed.

10. It is best for us to poke a small hole in the bottom of the lantern with scissors.

11. Cut the yarn into the same length, then tie a knot together, stuff it into the small hole just now, and the lantern is finished.

The steps to make the lantern are as follows:Prepare materials: handmade paper, scissors, glue sticks.

Operation steps: 1. Find another piece of red cardboard, and fold the cardboard bucket book to the posture several times.

2. Then use scissors to cut it according to **.

3. Then, cut it again.

4. Roll the cardboard a few more times, it looks arc-shaped.

5. Open it again, glue one side with double-sided tape, and glue the other side to the empty state, and it becomes a round barrel, <>

6. Shape the glued barrel again, press the two ends to the middle, and then slowly adjust the curvature of the paper strip with your hands, and the shape of the lantern is basically completed.