The new cup has a label on it, so how do you get rid of it?

It's good to soak it in water After soaking it down, tear it or soak it in water, don't touch the water with your hands, take a toothbrush.

Blow it with a hair dryer and tear it off when it's hot.

Take a hair dryer and try it.

Sticking a label to the cup does this and it is easy to remove without leaving a trace.

On the other side of the label, heat it with a hot blow dryer for about 3 minutes, and then tear it off directly by hand, if there is an offset print on it after tearing it off, you can wipe it off with a hot rag.

There are many ways to remove stains from smooth items at home, and here are some things you can try:

1. Use soap and a little ammonia and turpentine to mix liquid, you can remove a lot of offset printing on glass.

2. Use transparent adhesive with good viscosity to repeatedly stick and tear, and you can remove some of the surface.

3. Wipe it off with a little dilute sodium water, or use paint thinner.

4. You can use a hair dryer to dry, and then you can scrape it gently.

5. Wipe with a cotton swab dipped in nail polish remover.

6. Wipe the wind oil essence.

7. Use a special detergent or sneaker detergent to wipe it.

8. Use the 4B eraser for drawing to be very soft, and you can erase it with the Korean eraser.

9. If the traces that have been left for a long time have hardened, you can use a hot towel to soften it before wiping it.

Take a hair dryer and blow it will fall.

Gently scratch it off with a knife.

1. Find a bottle of hand cream, squeeze out an appropriate amount, evenly apply it to the residual glue, and let it stand for 5 minutes. Then do a manual erase.

2. For the case of less glue, wipe with a paper towel or wet towel, and wipe back and forth to solve this small problem.

3. Use the hot air blown out of the hair dryer to blow the residual glue, and you will find that after blowing, the residual glue will be wiped off easily.

4. Wipe the residual glue with wind oil essence, which can also be easily removed.

Erase with an eraser.

Operation steps: 1. Tear off the plastic film on the surface of the label on the plastic cup, and leave the adhesive on the cup.

2. Take a piece of eraser and wipe it back and forth on the remaining part of the adhesive tape.

3. The dander from the eraser is mixed with the adhesive tape and slowly falls off the cup.

4. After a few minutes of erasure, the adhesive tape will come off completely, and the label paper on the cup will be processed.

Put the plastic cup in the refrigerator for more than 2 hours, and take it out to easily remove the label paper from the plastic cup. Give it a try.

If it is not easy to tear off, you can soak it in warm water and wash it with dish soap or decontamination powder.

Apply wind oil essence and wait for a while before wiping it off, so that you can do it without leaving any traces.

Use an electric hair dryer to blow hot air on the label, and then slowly remove the label.

If it doesn't work, you can use a combination of the above two methods, and it will work.

Soak it in hot water and it can be easily ripped off.

Don't be in a hurry to tear the label first, use a hair dryer to blow it and then tear it, it's easy.

You can put a little alcohol or gasoline and rinse it off with water.

1. After using a hair dryer to blow it hot, it will be easy to tear a lot 2. Try it with hand cream, and say what fat is in the hand cream.

The label attached to the water cup can be removed in the following ways:

1.Use hot water to blanch the label. Soak the tumbler in hot water, or wrap the tumbler label in a hot towel to soften it before trying to peel it off.

2.Use alcohol or cooking oil. Apply a small amount of alcohol or cooking oil to the label and let it sit for a few minutes to make it easier to peel off.

3.Use a hair dryer to heat the label. J&H uses a hair dryer to quickly heat up the label for a few seconds, making the label glue soft and easier when removing the label.

4.Use the tape method. Attach a short piece of transparent tape to the label, and tear it off slowly after compaction, and the label will be torn off by the tape.

If none of the above works, you can also try a specialized cleaning product such as a label remover. However, before using these products, please read the product instructions carefully and test them on a small area to ensure that they do not cause damage to the water bottle.

In addition, for the label on the thermos cup, because the material is special, it is recommended to choose a cleaning agent specifically for the thermos cup when using cleaning products to ensure the protection of the thermos cup.

In our daily life, do you also have such troubles: the label on the bottom of the newly purchased cup is difficult to remove cleanly and without marks, and the bottom of the cup will always be sticky if you tear it with your bare hands? Below I will teach you a few tricks to easily remove the label from the cup.

First, the plastic cup label is skillfully removed.

1. Use a degreaser. For example, synthetic motor oil, nail polish remover (acetone), lighter oil (naphtha – those used in Zippo lighters). To test whether these degreasers are safe for your plastic products - there are some degreasers that can damage plastic products, choose a less conspicuous point on plastic products, use a cotton swab dipped in a little degreaser of your choice to apply, wait for at least 20 minutes, if there is no reaction, it proves that the degreaser you choose is safe for your plastic products.

2. Use a rag to dip it in and apply it or pour the degreaser directly on the label, or you can tear the label and pour it on those glue residues.

3. Wipe in a circle from the middle to the outside until there are no traces.

Although wiping will leave some stains on the box, they can be washed off with soapy water. 2. Usually before tearing these labels, it is best to use a hair dryer to blow first or cover it with hot water first, so that the glue and labels are heated and loosened before tearing.

3. If you have peanut butter at home, you can also test it, the grease in the peanut butter will melt the glue, and finally the peanut butter can be wiped off with a paper towel.

4. Solid car wax is also easy to use, apply a layer on the surface of the label, and after three minutes, it can be removed.

5. Vinegar is OK, moisten it, wait for it, wipe it off.

Second, the label of the glass cup is skillfully removed.

The adhesive label on the newly bought glass and other products is particularly difficult to tear, how to quickly and perfectly remove the label without leaving a trace? Today, I'm going to share with you the way I figured it out, which is also applicable to the removal of sticky label labels on other products (iron products, etc.), so that the surface temperature of the label is increased.

1. Pour hot water into the glass and submerge the label, at this time, the solidified adhesive will restore its viscosity, so that it is easy to tear off the label completely.

2. The label has been completely torn off, but there is still glue on the glass surface; Apply the hand cream to the glue place, similar to the principle of compatibility, wait for a minute Now the glue is very good to wipe clean, 3, wipe off with a rag and toilet paper.

Succeed! One on the side, dangdang, clean and slippery, no glue residue at all, perfect Similarly, this method also has an effect on ceramic and bone china cups. The above is the introduction of how to remove the label on the cup, we will often encounter the problem that the label of glass products and plastic products such as cups, water bottles and bowls and basins is difficult to remove, the above methods are also applicable, everyone quickly learn it.

1. Tear off the part of the printing paper on the surface of the label first, and try to tear it off as much as possible.

2. Put the bottom of the cup under the faucet and rinse it again, so that the stickers are not glued.

The paper is soaked first. 3. Next, take out the prepared hand cream and squeeze a small ball on it.

4. Keep rubbing on the surface with your hands, and you can use some force to fully soak the self-adhesive.

5. Wipe it off with a clean rag, or rinse it with water and wipe it again. The bottom of the cup has a new look!

Use a hair dryer to heat the air for two or three minutes or wipe the air oil on the labeling area.

1. Wipe with a cloth dipped in alcohol.

2. Sprinkle with talcum powder (prickly heat powder is acceptable) and gently remove it with your fingers.

4. Put it on the fire to bake it slightly or blow it on the label with a hair dryer for a while, and then rinse it with water, you can easily tear off the label.

Put some dish soap on top and wash it with a dishcloth, and it will be removed quickly without leaving scratches.

Sticking a label to the cup does this and it is easy to remove without leaving a trace.