The computer is connected to the mobile phone hotspot but cannot connect to the Internet

Some friends may have had such an experience, because there is no wireless router, so they set their computers as wifi hotspots, the hotspots are set correctly, and then the mobile phone can also be connected to the computer wifi hotspot, but just can't go to the network, why is this? It is very likely that your phone is not set up properly, so here is how to solve this problem.

The first step is to set up the wireless wifi hotspot of the computer, this step believes that many friends will, I will not say this, at this time open the network and sharing center of the computer, click on the change adapter settings in the left column, we can see the wifi hotspot icon in the open network connection center, the second step is to select the network connection of the computer connected to the network in the management page, right-click to select properties, pop up the setting box shown in the figure below, select the sharing tab, as shown in the figure, check the first option, And set the home network connection object to the network connection above.

The third step is to start the virtual wifi hotspot network card, click the network icon in the lower right corner, then we can see that the wifi hotspot has been started, and our mobile phone can connect to the computer network through it.

Step 4Find the wireless network connection in the first step 2 in the computer, open its status page, click on its details, view the IP address and gateway of the network connection, remember it, and take out the mobile phone, find the wifi hotspot on the computer you are connected to, long press the connection, select the modify network configuration command in the pop-up dialog box, click on the advanced options, pull the page to the bottom, click on the IP address, and fill in the various IP addresses and gateways just written down from the computer to the mobile phone. Then save, at this time the phone can not only connect to the wifi hotspot of the computer, but also successfully surf the Internet.

The computer can't connect to the phone hotspot.

Reasons why the computer can't connect to the mobile phone hotspot on the Internet:

1. It may be that the wifi function of the computer is not turned on, or the computer may have turned on the airplane mode.

Solution: Turn on the wifi function of the computer, or maybe restart the computer after the airplane mode is closed.

2. It may be that the hotspot is not turned on, or the computer is too far away from the hotspot.

Solution: After turning on the hotspot, leave the computer close to the hotspot.

3. It may be that the hotspot is disabled without vigilance, resulting in the network being unable to connect.

Solution: Open the Windows settings interface, and then select "Network & Internet", "WLAN", and "Change Adapter" in order.

Settings option to find the disabled wireless network.

and right-click and select Enable.

4. It may be that the hardware related to the computer and the network connection has failed, which directly causes the network connection function to be unable to be used normally.

Solution: Contact the computer after-sales service, and then let the professional staff reflect and train the computer.

Precautions for connecting computers to mobile phone hotspots

The computer is connected to the mobile phone hotspot, the mobile phone shares the network, at this time we must pay attention to the use of mobile phone traffic, you know, the use of traffic on the computer is not the same as the use of traffic on the mobile phone, the same one**, the mobile phone** needs 30m traffic, but on the computer it needs 100m or even more.

Therefore, when the computer shares the network, it is necessary to control the use of traffic, and if you accidentally use more traffic, the gain outweighs the loss.

If your computer is connected to a mobile hotspot and cannot access the Internet, it may be caused by the following reasons:1Mobile hotspot setting issues:

Make sure your hotspot is set up and turned on correctly, and make sure the hotspot name and password are correct. 2.Problems with computer network settings:

Please make sure that your computer has installed the correct wireless card driver, otherwise you may not be able to connect to the hotspot. 4.Mobile phone Xinhong good number problem:

If your phone signal is unstable or your cellular network is unstable, your computer may not be able to connect to the hotspot. Workaround:1

Check whether the hotspot settings on your phone are correct, and reset the hotspot name and password. 2.Check whether the computer network settings are correct, and try to reset the IP address, subnet mask, default bridge family gateway, etc.

3.Check that the PC's wireless card drivers are installed correctly and try to reinstall the drivers. 4.

Try connecting to a hotspot in a different location or at a different time to determine if it's caused by a cell signal or network issue. If none of the above methods can solve the problem, it is recommended to contact the customer service of the mobile phone or electrosensitive brain manufacturer for consultation.

The following three methods can be referred to:

Method 1: Network diagnosis.

1. Right-click the network icon in the notification bar to open the Network and Sharing Center.

2. In the Network & Sharing Center, find the connected mobile network hotspot and tap it.

3. Click the diagnosis function to diagnose the problem that the network cannot be connected.

<> Method 2: PC Manager Repair.

2. After the test is completed, click Network Repair, or switch to the Network Repair tab for repair.

3. Click on the full detection in Network Repair.

4. After the detection is completed, the detected network problems will be displayed, click Fix Now.

5. The display has been repaired, and you can use click to verify to test whether you can surf the Internet normally.

Method 3: Check the parameters of the DNS server.

1. Open the network connection in the control panel and find the mobile network hotspot you are connected to.

2. Right-click the network connection and select the click properties function in the pop-up menu.

3. In the WLAN properties window, find Internet Protocol version 4 and click on it, then click on Properties.

4. Finally, change the parameters of the DNS preferred server to the parameters in the figure, and check the Verify on Exit setting.