How to set up the campus network with the polar router, and how to set up the Internet with the pola

Device connection. IP address settings.

Internet account and other parameter settings.

In addition, you should also pay attention to how to set the password of the router.

Go to the desktop of your computer, right-click on "Network", and select "Properties".

Go to the Network & Internet page and click on "Ethernet".

Then tap on "Details".

Enter the gateway you just found in the address bar of the browser to enter the management interface of Tengda router.

Select the Internet access settings and change the Internet access method to "ADSL dialing".

Enter your own broadband and broadband password.

Then set the password for your own wifi, and finally click "OK".

Then tap on "Advanced Settings".

Now you can see that the network has been successfully connected.

Click "Internet Settings", you can see that there are several ways to explain the way to access the Internet in the helpful information on the right, and you can modify the Internet access method in the circle options.

Then you can choose to modify the connection mode, and click "OK" after modifying.

The steps are as follows:

1. Connect the LAN port of the router and the computer network port with a network cable;

2. Enter the web management page of the wireless router; (In most cases, the address is admin and the password is admin, see the instructions at the bottom of the router.)

3. Open the DHCP management item of the wireless router, turn off the DHCP function (enabled by default), and set the wireless password;

4. Save the settings, restart the router and computer;

5. Connect the campus network port with the LAN port of the wireless router with a network cable;

6. Start Ruijie and select Ruijie's connection network card as the wireless network card.

Note: Ruijie authentication does not allow a machine to have two running network cards, otherwise the current system working environment and the software operating environment will pop up after authentication, and the software can not operate normally!

7. Set the IP address in the wireless network card;

8. Click Authenticate.

Polar router is a commonly used network device, which can help us to set up and manage home networks. Setting up Internet access on the polar route is an important step, so let's take a closer look at how to set it up.

The first step is to connect the pole route. Plug the polar router into a power source and connect it with a device such as a computer or mobile phone. If you are setting it up from a computer, you need to use a network cable to connect the polar router to the computer.

If you want to set it up with a mobile phone, you need to connect your phone to the Wi-Fi signal of the polar router.

The second step is to enter the Polar Route Management page. Open the browser, enter in the address bar, and press the enter key to enter the management interface of Polar Route. If it is your first time entering, you will need to enter your administrator and password to log in.

The third step is to set up the network. In the admin interface, find the Network Settings option, click Enter, and select "Broadband Connection Settings". Here you will need to enter the password provided by the operator, as well as some other necessary network information.

If you are not sure how to set it up, you can consult your carrier's customer service or check the instructions provided by your carrier.

Step 4: Set up Wi-Fi. In the admin interface, find the Wi-Fi settings option and click to enter. Here you can set the Wi-Fi name and password, and select the security level of the Wi-Fi.

The WPA2-PSK security level is recommended to protect the network.

Step 5: Save the settings. Once you've done all the settings, be sure to save them. Click the "Save" button at the bottom of the page and wait a few seconds until the mess is set to save the cavity is successful.

The above are the detailed steps to set up the Internet on the polar route. During the setup process, if you encounter any problems, you can refer to the user manual of Polar Routing or consult customer service. At the same time, it is also necessary to pay attention to network security to protect personal information and the security of your home network.

Operating tools: Dell laptop, win10, router latest finger version.

1. Open the browser, type", and click "Enter".

2. Enter the "Manage Password" and click "Enter".

3. Click on the "Internet" option, you can choose the way to access the Internet.

4. Click "Settings", enter "Broadband Account" and "Broadband Password", and click "Save".

5. Click on the "WiFi" option, click on "Settings" behind "WiFi Basic Settings", you can set the WiFi name and password, and click "Save".

6. Click "System Settings", if it is 100 Gigabit broadband, you can turn on the "Switch" behind "Speed Mode", and close the browser when you are done.

1. The router is connected to the campus network.

Connect the campus network cable to the WAN port of the router, and use the network cable to connect the computer to any LAN port of the router. Then start the computer, when the LAN port flashes, it means that the computer and the router have successfully established communication.

2. The system is connected to the router.

Turn on the wifi of the computer, search for the default wifi name of the router (the nameplate on the back of the router is written), and connect to the wifi network. The first time you use the router, you generally don't need to enter the wifi password.

3. Enter the gateway interface.

Open the computer browser and enter the gateway IP address (usually the gateway IP address with the nameplate behind the router) to enter the gateway configuration interface. (This interface will pop up automatically for new routes).

4. Set up the Internet mode.

Go to the WAN port settings in Advanced settings. If the broadband service requires dial-up, select PPPoE dial-up, otherwise you can choose DHCP to get automatically. To dial up PPPoE, enter the broadband password, and select Automatic connection as the connection mode.

If DHCP is automatically obtained, you do not need to enter this field.

5. Set the wifi name and password.

Go to Wireless Security in the Wireless Settings and select WPA2-PSK mode for Security Mode. Select AES for WPA encryption rule. Set up a wireless network key. The router will automatically restart after setting, please enter a new wifi password to connect.

As follows: 1. What is fiber broadband at home? Which operator's, can the optical modem directly access the Internet?

2. If possible, the modem is in routing mode, and the back-end router WAN port is connected to the Gigabit LAN port of the optical modem.

3. After that, the mobile phone is connected to the wifi of this router, and then open the browser, and enter the default IP address of the polar router.

4. After entering, set it to automatically obtain, and then click Next to set up WiFi.

The broadband account number and broadband password are provided by your broadband operator, and must be filled in correctly. If you fill in the wrong information, you will not be able to access the Internet; According to statistics, more than 75% of users are unable to access the Internet after setting up the broadband account and password because they filled in the wrong broadband account and password.

Automatic Internet access. When you turn on broadband, the operator provides you with any information; If you don't have a router, you can connect a broadband cable to your computer and you can access the Internet.

Then when setting the polar route to access the Internet, the Internet access mode should be selected: automatic Internet access - > click "Internet Now".

How to set up the polar route.

Method steps.

Open your browser, type", and click Enter.

Please click Enter a description.

Enter the "Manage Password" and click "Enter".

Please click Enter a description.

Click on the "Internet" option and you can choose how to access the Internet.

Please click Enter a description.

Click "Settings", enter "Broadband Account" and "Broadband Password", and click "Save".

Please click Enter a description.

Click on the "WiFi" option, click on "Settings" behind "WiFi Basic Settings", you can set the WiFi name and password, and click "Save".

Please click Enter a description.

Click "System Settings", if it is 100 Gigabit broadband, you can turn on the "Switch" behind "Speed Mode", and close the browser when you are done.

Please click Enter a description.

In the settings of the TV,There is a network connection,Click on it,Fill in the account and password,Just confirm。 My family uses the pole route, which is very easy to use.