-
Anonymous users2024-02-06Hello, the router needs to be set up before it can be used, please confirm whether your router has set the parameters, if it is not set to enter the background to set the parameters, for reference only, more Anhui Telecom**, business information can be paid attention to Anhui Telecom***.
-
Anonymous users2024-02-05Generally, there are several reasons why the router cannot be opened.
The router's wireless password is not set to be turned on.
Solution: Log in to, and there is a WAN setting in it. You can create a wireless network password inside, and you can set it.
Problems with router settings.
Solution: When you confirm that there is no abnormality in the 1 setting, it means that the previous settings of the router are abnormal and you need to reset the settings. Find the reset button on the router itself--- press and hold it for 10 seconds--- then reset the router again.
Router hardware issues.
Solution: When the reset is invalid, you need to overhaul the router hardware, it is recommended to find the router after-sales service.
To set up, connect the computer network card with the LAN port of the router with a network cable and turn on the power of the router; Double-click the IE browser on the computer, enter the IP address of the router default settings page in the address bar, and press Enter; Enter the default username: admin, and the default password:
admin；Click OK. Click Setup Wizard in the left rail, click Next; Click on ADSL Virtual Dialing (PPPoE) and click Next; Enter the broadband, password, and click Next; Click Done. Many friends think that the dial-up connection is over after setting up, but in fact, there is still one point that is not completed.
Because the following settings are not completed, many friends fail to dial up, or can connect to the network, but it will be dropped after a short time. Let's continue the settings: click the MAC address clone menu in the network parameters menu on the left sidebar, click Clone MAC address in the interface that appears, and click Save.
At this point, the router will prompt you to restart the router, click OK to restart the router. After the router restarts, close the Internet Explorer. Connect the WAN port of the router with an incoming network cable, and then connect the computer to the LAN port of the router with a network cable to start surfing the Internet.
-
Anonymous users2024-02-04Hello, I have seen your question and am sorting out the answer, please be patient for a minute.
What should I do if the router is connected but I can't connect to the Internet, and the wifi can't be connected? It's easy to ask questions in one move. What should I do if the Wifl shows a connection but no internet connection?
1.Open Settings, and in the settings interface, tap Wi-Fi; 2.Select the wifi that has been connected, click on an i icon in the circle at the back, you can see his configuration IP, it will be automatically changed to manual, manually enter the IP address; 3.
Go back to Settings, find General, find Restore, click Reset Network Settings, enter the password and restart your phone.
-
Anonymous users2024-02-03Introduction: Many people buy a new router, and they don't know how to get in without a network connection, usually 1 or 253). Here, I will take TP-Link routing and prediction routing as examples to introduce the setting method.
Stage 1: The router turns on
The router is powered on, and the computer or mobile phone is connected to a wireless signal (local connection will be limited due to no network access, but that's okay).
Note:
The computer must be connected to the wireless first, and then proceed to the "second step: set a fixed IP".
Step 2: Set a fixed IP address
Hover the cursor on the wifi, right-click to pop up the following interface, and click to open the Network and Sharing Center.
As follows, tap on the wifi name.
The wifi status bar pops up, and there is "Attribute Changpi" in the lower left corner, click it.
The following page pops up, scroll down, find IPv4, and click.
Select Manually obtain an IP address.
Note:
1. Different routing requirements'The IP may not be the same, you can go to the ** routing manual of this model on the network Xunchun and check the relevant address. (Generally, x is in the range of 2-254.) Some for:
2. Please be sure to connect to the route first (it will generally be displayed restricted), and then set the IP address, otherwise the IP setting will be invalid.
Landing. Enter or in the address bar of Internet Explorer, and the login interface will pop up, and you can enter your username and password.
Note:
1. The IP login of different routes may be different, you can check the label of the router body, and generally have login IP, user name, password and other information. Or check the routing manual of this model on the network annihilation.
2. Try to use IE browser to log in, a few third-party routes can't log in.
Precautions
Some models of Lenovo route do not need to reset the IP, and can be entered directly by entering.
1) **The line is often hit by wind and rain, which affects the communication quality, which is the main reason for frequent drops. >>>More
The router has been restored to factory settings, and the network parameters such as dial-up settings and related wifi settings have been restored to factory settings, so the network cannot be connected, and the solution is to reset the router. >>>More
Looking at your screenshots, you probably want to limit other people's Internet speeds. >>>More
You should fix the IP for yourself, and fix the IP for your neighbors, and you can see the name and MAC address of the machine that is accessing the route in other pages, and you can generally set up to log in to your MAC to the route (this is to prevent ARP attacks and limit the network speed). >>>More
From the LAN port of the main router, a network cable comes out and connects to the LAN port of the wireless router, log in to the wireless router, turn off the DHCP service of the wireless router, and set the IP address of the LAN of the wireless router, which should be different from the LAN IP of the main router.