How do I set up a route on a newly opened network?

The installation and setup of the router is as follows:

1.First connect the line, you can refer to the figure below.

2.After the line is connected, open a browser, enter the management address and management password of the router, and then enter the router background (the login address and login password of the specific router can refer to the manual or the label on the back of the router).

3.Once you've logged in to your back-office, select Quick Settings, then click Next.

4.Choose the way to access the Internet, usually ADSL users choose the first PPPoE, if you use other network service providers, then choose the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

5.Enter the password applied for from the network service provider, and go directly to the next step after entering.

6.Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

7.After entering it correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

Look at the router's manual.

The general way is to open the Internet Explorer browser and type it in the address bar.

You will be taken to the router's settings page.

Fill in your ADSL password and put the auto-login on it!

That's pretty much it!

Still pay attention to the manuals of the router!!

2: A dialog box pops up, and the user and password are: admin3: click Basic Configuration.

4: Select WAN configuration.

5: Select the first one and click the pen in the operation.

6: Enter the number and password of the Internet card you bought in the username and password.

7: Reboot and it's OK.

Internet Explorer right-click - Properties - "Connections" tab - "Always dial the default connection" so that the dial-up connection can be removed. As for the fact that only one machine can access the Internet, your route has not been set up yet, you just need to watch it carefully!

After logging in to the route, fill in the IP number as the route in the LAN settings, usually or just check the DHCP!

The settings in the route are not adjusted. It's good to be fine.

When you buy a route, it is equipped with a manual, and you can also try the upstairs method when you set it upstairs, and finally prompt you to go down!! After setting it up, turn on the power and modem and you can go directly to the Internet, no broadband dial-up is required!!

Read the manual, if you can't even read the manual, I advise you to send the road rover back. Actually, it's very simple, I also read the manual to figure it out myself, good luck.

For newly purchased routers, the following describes how to set them up.

Step 1: First connect the router to the power supply and use a [finished network cable].

Plug the two ends of the network cable into the [Router WLAN] and [Computer Network Port] respectively.

Step 2: Press the [Power Button] of the computer and [Start the Computer System] to enter the desktop.

Click the Enter key, and the router login interface will pop up, enter the correct [Administrator Password], and click OK.

Step 3: Enter the login router settings interface.

Select Setup Wizard and click Next

Select a broadband connection method.

Router settings screen.

1.At this time, if the broadband in the home is accessed, it belongs to the [optical fiber network].

Directly select [Dynamic Mode] and click [Next].

Set a wireless Internet password, and after saving it successfully, the router will automatically restart to realize the Internet function.

2.If it is a normal ** dial-up, broadband network.

You need to select the PPPoE (ADSL Virtual Dialing) mode.

Then enter it next. After saving the broadband account password, restart the router.

Once the router is set up, you can surf the internet.

Secondly, there are various brands of routers in the market, and the method of setting up Internet access is basically the same.

You can also refer to the [Product Manual] of the router you purchased.

Make the correct way to set up your Internet access.

How to set up the newly bought router, the master teaches you to operate it with a mobile phone, and you can surf the Internet in two minutes.

Next, enter the administrator password.

Then click on "Extranet Settings" on the left

Then select the networking mode as "Broadband Dialing", then enter the broadband account number and password, and click Connect.

2. Set up wifi

Select Wireless Settings on the left and click "Wireless Name & Password".

Then enter the wireless network name and password, and click Save.

Finally, exit to complete the setup.

The steps to set up the new router are as follows:

1. The newly purchased router is connected to the wall network port of the optical modem broadband network cable.

The WAN interface on the new router must be connected to the optical modem broadband network cable and wall network port; If you have a network device such as a computer or TV, connect it to the LAN port on the new router with a network cable.

If the newly purchased router supports WAN adaptation, that is, it does not distinguish between WAN port and LAN port; In this case, any interface on it can be connected to the optical modem broadband network cable wall network port, and the router will automatically use this interface as the WAN port and the remaining interface as the LAN port.

Different routers have different parameters such as management address, default wifi name and password; So, be sure to check it out for yourself.

3. You need to connect your phone to the default wifi of the new router, and you can set it up after connecting.

After the phone is connected to the default wifi network of the new router, it is normal for the phone to not be able to access the Internet, please don't worry. At this time, the mobile phone can enter the router settings interface and set up the router.

4. At present, most wireless routers, after the mobile phone is connected to its default wifi network, the mobile phone browser will automatically pop up the settings page; At this point, just follow the prompts on the page.

5. According to the prompts, set the wireless name and wireless password of the router.

6. After completing the setup, the default wifi signal of your old router will disappear.

The phone needs to be connected to the newly set wifi, and it can be connected to the Internet.

Here's how to set up your router:

2. Then open the browser of the computer, enter the login address and login password of the router, and the specific login IP and password can be looked at the label on the back of the router.

3. After entering the router, there will be a setup wizard, first fill in your broadband account and password.

4. Then set the wireless name and connection password.

5. After the successful setting, a prompt will appear for the successful setting, and it will take effect by restarting the router.

The first picture is fine, and the third positive image is fine by default.

The biggest problem is the second picture.

You'd better understand what your current topology is, it's impossible to network like that.

If you are connected to an optical modem and the optical modem dials up, select Auto Get, or if it is a router dial-up, select PPPoE and fill in the broadband and password.

If it is capricious, it is just that if you want to connect it like this, the IP network segment of the first picture should be changed to a different one from the WAN port.

If DHCP is enabled on the higher-level device on the WAN port, you can directly select automatic acquisition. If there is a conflict with the IP address of the LAN port, change the IP address of the LAN port.

The new router is from 2014?

If there is a default username, password, and IP on the sticker of this router, the network cable connected to the modem can directly connect to the computer to access the Internet normally. Then the router is not connected to the optical modem temporarily, the computer network cable is connected to the router LAN port, open the browser, enter the default IP login interface username and password, you can enter the router management page, and set the SSID and your own password on the wireless wifi settings page. Save and exit,Connect the network cable from the optical modem to the router WAN port,Restart the browser,Just open the web page。

First of all, whether the router you set up is used as a bridge or just dial-up through him to access the Internet, different function settings are different.

1.If it's dial-up, this setting doesn't seem to be much of a problem.

2.If it is used as a bridge, you need to set the WAN port to free acquisition, and set the LAN port on the first page to This X number is to distinguish it from the router that can dial up the Internet, otherwise the two conflict, you can only connect to the lack of network.