How to remove and replace the car s in car reading light?

Method: 1. The headlamp is relatively complicated, there are a total of three lamps in the front, and a knife or screwdriver is used along the front part of the U-shape.

Pry open. <>

2. Disassembly is completed.

<>3. Unplug the lampshade to take out the bulb.

4. Install the LED tail box bulb, pay attention to the flat insertion, ensure that the plug is very tight, and the interface part is connected to it.

Pry slowly along the outermost part with "one word", and do not warp the middle part of the lampshade. There are small Phillips screws or buckles inside. Remove and replace.

First, pry off the plastic lampshade with a straight change cone. There are small Phillips screws or buckles inside. Remove and replace.

When the light in the car is insufficient, the reading light can provide enough brightness for the occupants to facilitate reading in the car, and at the same time will not affect the normal driving of the driver. Connect the cigarette lighter interface, touch the switch, and it can emit different colors of light.

There are two types of reading lights in the car: ordinary reading lights (one light bulb) and LED reading lights (multiple LED lights). Significant advantages of LED interior reading lights.

When the switch is in the "door" position B, if the door is opened, the light is on. It is equipped with an interior light timer, and the interior light will continue to be lit for about 15 seconds in the following cases.

The ignition turns to"on"Location. When the rear reading light switch is in the "on" position C, the rear reading light will light up no matter what state it is in. When the switch is in the "off" position A, the rear reading light does not light up, regardless of the state.

1、First, use a small knife to pry open the buckle from the lower part of the interior ceiling light.

2. As long as you break free of the lower buckle, you can take off the translucent plastic cover, and you can see the internal structure of the indoor ceiling light.

3. The picture shows normal, the new dome light bulb, the filament is intact, and the appearance is normal.

4. Install the new ceiling light bulb.

5. When installing the translucent cover, first align the two buckles on the upper part, and then press down the buckle at the bottom to fix it.

6. The final replacement was successful.

The front reading lamp is fixed by using a buckle, the lamp shell is surrounded by small plastic clips, which can be unlocked by prying slowly, and the use of a plastic spudger to operate can reduce the risk of damaging the lamp shell, the specific operation steps are as follows:

1. Find the reading light located on the roof of the driver's head.

2. Open the glasses case in front of the reading lamp.

3. Use a plastic spudger to pry the edge of the reading lamp.

4. Pull down with hand assistance to remove it.

5. Pull the internal lamp bead to remove the bulb.

The front reading lamp is fixed by using a buckle, the lamp shell is surrounded by small plastic clips, which can be unlocked by prying slowly, and the use of a plastic spudger to operate can reduce the risk of damaging the lamp shell, the specific operation steps are as follows:

1. Find the reading light located on the roof of the driver's head.

2. Open the glasses case in front of the reading lamp.

3. Use a plastic spudger to pry the edge of the reading lamp.

4. Pull down with hand assistance to remove it.

5. Pull the internal lamp bead to remove the bulb.

It's very easy to dismantle, when dismantling, the lamp is pushed to the front, and then you can break it out from the seam at the back, anyway, even if you pick it with your fingernails, use both hands to get the back of the lamp out first, and then the whole thing comes out.

For more information, please refer to Ekcar.

Slowly pry along the outermost lead circumference with "one word", and do not warp the middle part of the lampshade. There are small Phillips screws or buckles inside. Remove and replace.

Start by priing open the plastic lampshade with a screwdriver. There are small Phillips screws or buckles inside. Remove and replace it.

The reading light can provide passengers with enough brightness when the light in the car is insufficient, so as to facilitate reading in the car, and at the same time, it will not affect the normal driving of the driver. Connect the cigarette lighter interface, touch the switch, and it can emit different colors of light.

Car reading lights have normal reading lights (one light bulb) and LED reading lights (multiple LED lights). Significant advantages of LED interior reading lights.

When the switch is in the "door" position B, the light will turn on if the door is open. Equipped with an interior light timer, the interior light will continue to turn on for about 15 seconds when the following happens: Turn the ignition toward"on"Location.

When the rear reading light switch is in the "on" position C, the rear reading light will light up regardless of the status. When the switch is in the "off" position A, the rear reading light does not illuminate, regardless of the status.

Millions of car purchase subsidies.