-
Let's get started. As the name suggests, offline programming is done offline. Unlike normal robot teach-in programming, this means that in the process of offline programming of the robot,Robots don't have to leave the production line, and production doesn't have to be interrupted
After importing the CAD data into the computer, the programmer can use the offline programming software to set up the robot's arm configuration, feed rate, power, motion trajectory, etc., without considering the dynamic process requirements, to create, optimize and validate the production plan. Once the programming is complete, the actual machining process is carried out by the automated system. At the same time, the monitoring of the execution effect is also fully automated.
This way, you can be sure ofShortest cycle times and best production results。Offline programmingIt is especially suitable for programming tasks with very complex trajectories。From a single robot cell, multiple robots to collaboration, to the programming of the entire production line, the advantages of offline programming are significantly greater than manual teaching.
AdoptionMulti-variety and small batchesEnterprises that want to build and install processing units are often worried that the implementation of new plans will affect the production schedule. If the robot is taught by hand, the entire teaching process can often take days or even weeks. During this period, the robots cannot be produced at the same time and must be stopped.
Not only that, but only when all the new facilities have been installed can the teaching begin. Naturally, your production schedule and output are severely impacted.
By using offline programming software, the programming and validation of the robot will be stripped away from the actual installation. The software has programmed and validated the robot before the production facility for a new machining cell or new part is actually set up. In this way, as soon as the actual installation is complete, the robot can start production immediately.
Timeline comparison of offline programming and manual teaching.
Another disadvantage of manual teach-in is that the programming results are highly dependent on the operator's work experience and personal level. Offline programming is done by computerThe accuracy is much higher than that of manual teach-in
The offline programming software developed by the robot manufacturer itself generally only has good compatibility with its own brand of robots, while the third-party offline programming software developed by the software company usually has the advantage of supporting a variety of different brands of robots.
Another benefit of using offline programming software is:Ensure industrial safety and avoid engineers working in dangerous environments。Engineers can better plan their working hours and focus on creative work.
-
Offline programming does not occupy the working time of the robot, and you can also prepare for work in advance, you can search for bw-cam
2018 offline programming software is an offline programming software independently developed by Guangzhou Bowen Robotics Technology Co., Ltd.
-
I think the biggest advantage is that you don't need to install any environment on the client side, and it's easy to learn
-
You can program without using the network and in a stand-alone state.
-
Summary. Before the programming program, the system parameters should be checked and confirmed, the system parameters mainly include mechanical parameters, operation parameters, nozzle parameters, identification parameters, under normal circumstances, the system parameters of the placement machine have been adjusted at the factory, do not change easily, but some parameters are related to the NC program to pay attention to; The data type in the operation data, such as the coordinate ABS and the relative coordinate INC should be consistent with the data type in the NC program, and the function of prohibiting the placement of the middle product in the operation data should correspond to the NC program; For fine-pitch ICs, if there is a device number on the PCB board during programming, the X and Y coordinates are determined by the device designator, and the placement position of the IC can be accurate.
Before the programming program, the system parameters should be checked and confirmed, the system parameters mainly include mechanical parameters, operation parameters, nozzle parameters, identification parameters, in general, the system parameters of the placement machine have been adjusted at the factory, do not change easily, but some parameters are related to the NC program to pay attention to; The data types in the operation data, such as the sitting and macro vertical ABS and the relative coordinate INC should be consistent with the data call type in the NC program, and the prohibiting placement function in the middle of the operation data should correspond to the NC program; For fine-pitch ICs, if there is a device number on the PCB board during programming, the X and Y coordinates are determined by the device designator, and the placement position of the IC can be accurate.
-
BW-CAM 2018 offline programming software is very good, it has strong programming capabilities and comprehensive data interfaces, and also supports all brands of robots, you can try, the official website has a trial version.
-
BW-CAM 2018 offline programming software is quite easy to use, we use this in the training room, it has strong programming capabilities and comprehensive data interfaces, and also supports all brands of robots, you can try it, there is a trial version on the official website.
-
The domestic easy-to-use robot offline programming software robotart, PQART, comprehensive functions, the most important thing is that it is very easy to get started, can do what you see is what you get, direct output execution**, U disk copy to the robot can be run, suitable for robots to do welding, grinding, cutting, spraying and other robot programming, if the advantage of robot programming is that the speed is much faster than manual teaching, and simple and easy to operate, the accuracy can be done theoretically zero error 23
-
It does not only include computer programs that can be run on a computer (in this case, a computer in a broad sense), but also documents related to these computer programs are generally considered to be part of the software. To put it simply, software is a collection of programs and documents. In addition, it also refers to the management system, ideological ideology, ideological and political consciousness, laws and regulations in the social structure.
-
Take a piece of my heart, send the blue sky, through the air, accompanied by the breeze, to your side, and send sincere wishes: good health, all wishes come true, smooth sailing.
-
Check it up on the Internet to get married quickly, there is such a software, mobile phone software engineering, look at it, it's so impressive.
visual c++
Non-computer majors learn more about this. However, there are also some schools that learn C. >>>More
Pro, the difference between robot programming and graphic programming 1, the definition is different: programming design has a "controllable system" with the role of logic flow, programming is not necessarily for computer programs, for the system with logical computing power, can be considered programming. Robot programming is a sequential description of actions set up to enable a robot to accomplish a certain task. >>>More
I don't think so, but a lot of it is the basic word in English or something, we know it, so you can learn this if you are not good at English, as long as you know the basic words. Below is an extension of the software. >>>More
Many people think that students who graduate from junior high school are too young and have too weak a cultural foundation to learn such a lofty major as software development. But that's not the case. >>>More
Development is a little higher for computers. Why? Because you need to run some large development environments. Therefore, the configuration recommendation should be high. >>>More