What s going on with the 460 Pilot engine humming

It is recommended to use a decoder to read the fault code, and then repair it according to the fault code.

When my 460 accelerates, the car pants so badly that it's going on? There are also cars that turn off after about 10 minutes, and then turn on the fire for about 20 seconds, and then turn off the car by itself, and then only the pump oil can start the car.

I can't find out what the problem is. I was depressed and asked the master for advice.

Hello, you open the hood and smell if there is a mushy smell and suspect that the clutch plates are worn.

Did you check out anything wrong, and mine was the same, all of a sudden.

Mine is also only 30,000 kilometers away, and I really want to burn it.

The oil circuit is not smooth, there should be a blockage.

Mine too, the engine sound, the big power is not good, no energy, sometimes running normally, it turns off and can be played at that time, the friction plate is also changed, the data is brushed, it still doesn't work, my head hurts.

Mine too, did you find the problem.

Did you find out what's wrong?

This is because the engine lubricating oil flows back to the oil pan, and when the engine is cold started, the oil pump cannot establish the oil pressure in the first time, and the internal valves are not fully lubricated, so there is an obvious abnormal noise.

The engine fault light is on, indicating that the user's vehicle is faulty. If you are driving, don't panic, you can observe whether the water temperature gauge indicates that it is normal and feel how the engine is running. If the water temperature is normal, the engine is not abnormal (such as abnormal noise or shaking, etc.), the user can drive the vehicle to the nearest service station to check and maintain, prevent the long-term sick driving to cause adverse effects on the vehicle, and pay attention to the high speed during driving; If the water temperature is high, or the engine has abnormal noise, please find a safe place to park nearby, and contact the service station for rescue treatment.

Hello, when the engine fault light is on, it means that there is a problem with the electronic components in your car. It is recommended to go to the 4S shop to read the fault code with a computer decoder, repair it according to the fault code, and then clear the fault code.

Hello, the engine is generally mostly caused by the fuel emission system, and you need to go to the store in time to check the fault code to see if it is a problem with the engine or a sensor failure.

The meaning of the fault lamp is more, from the oil circuit to the circuit any place where there is a failure, the light will be on, and the fault needs to be read with a decoder.

In your case, it is recommended that you go to the local professional repair shop and let the master use the computer to detect the fault** and then deal with it.

Hello, if the engine fault light is always on, it is generally caused by engine failure, and it is recommended to go to the 4S shop for maintenance as soon as possible.

In this case, it is recommended to go to the 4S shop or repair shop for inspection and maintenance in time so as not to affect the safety performance of the vehicle.

Hello, the engine failure light of this car needs to go to the repair shop, or I am looking for a computer to check what is the cause?

Hello! For this case, it is mainly due to the failure of the electronic control system of the engine, this time it is recommended that you go to the repair shop to read the specific fault ** with a decoder, and then repair it according to the prompt of the fault **.

In this case, it is recommended to read the fault code of the vehicle to see what causes the engine failure light to turn on.

The reason is that the internal gear of the starter loses lubrication, and the phenomenon of astringency and jamming occurs, which affects the timely return of the gear. That is, when the engine is started, the starter rotates to drive the flywheel to rotate, so that the engine starts, and the speed of the engine is driven by the starter, so the engine speed is lower than the starter speed, when the engine starts and the speed is higher than the starter speed, the manual operation ignition switch is powered off and the starter is closed. Because the inside of the starter is too dirty, the lubricating oil fails, and the flywheel engine is forced to drive the starter to run at its own speed, because there is a speed difference between the two, at this time, the starter produces the sound of "bang" that we all hear.

This sound does not end until the starter is hot with the engine, but it will occur once every time it is started. To get rid of this sound, you can only clean and maintain the starter or replace the starter, but the effect of cleaning and maintenance will not be very good, and it won't take long to ring again, so if you can tolerate this sound, you still don't change it, and wait until it is broken and completely solved.

A ringing valve may be a broken valve seat. caused by air leakage. It must be removed and replaced.

If the vehicle has such a fault phenomenon, it is recommended to check whether the gears inside the gearbox are working properly, and to check whether the fixing screws that fix the engine and gearbox are loose.