Badminton stringing, the benefits of badminton stringing pre pulling

How much does a badminton racket string cost?

The quality of the badminton string is very important, it is related to the situation of the line, the stability of the ball control and the quality of the force. If the quality of the string is poor, it is easy to lose the pound and the thread loss is serious, and in serious cases, it may cause the uneven force of the racket to deform, so we must have an understanding of the knowledge of the string.

1. Pull wire method: four knot method and two knot method:

1) Four knots.

Yonex. Stringing method. It is divided into two lines, and the wearing method is separated horizontally and vertically, and there are four knots. The four-knot method unifies that the horizontal line is 10% pounds higher than the vertical line, which is generally 2 pounds higher.

The four-knot method of stringing can make the wire bed more evenly stressed, but it is easy to lose the weight and transport.

2) Two-section method.

Li ning. and the way of stringing victory. There is one thread to complete the whole process, so there are only two knots, so it is called two knots. Generally speaking, the horizontal line is also 2 pounds higher than the vertical line.

The two-knot stringing method can ensure the number of pounds well, but the wire bed is easy to be stressed unevenly, which is not conducive to control.

The badminton stringing tutorial is as follows:

1. Remove the previous broken string on the badminton racket.

2. After dismantling, like me, use the needle to guide the thread and start to weave the vertical line on the pure virtual racket. Tighten the thread at any time during the knitting time, and do not let the thread appear loose. (Point 1:.)

Prepare a 5-meter-long thread, thread the needle, and then thread the silver locust in the 8th hole, then in the 8th hole on the opposite side, then back in it, and then through the end of the 24th hole. ）

3. After the vertical line is braided, start to weave the horizontal line, and use the same method for the top. (Point 2: Then we knit the horizontal edge according to the same method as the front pants, and the needle and thread are passed through the vertical line one by one, and then the hole is threaded, and the knitting is done in this way.) ）

4. At the end, tie the two threads together and cut off the excess threads. (Point 3: When tying the knot, be sure to tighten both the horizontal and vertical lines before fixing them.) ）

Badminton rackets are generally composed of a racket head, a racket shaft, a racket handle, and a joint between the racket frame and the racket. The length of a racket should not exceed 68 cm, of which the length of the racket handle and shaft should not exceed 42 cm, the length of the racket frame should not exceed 25 cm, and the width should be 20 cm.

With the development of science and technology, the development of rackets is developing in the direction of lighter and lighter weight, harder and harder frames, better and better elasticity of racket shafts, and smaller and smaller air resistance.

Badminton rackets are very easy to break, accidentally the shuttlecock passes through the badminton racket, rotten holes, then you need to re-string, let's learn how to string together.

Method Steps:

1. Remove the previous broken string on the badminton racket.

2. After dismantling, start knitting the vertical line on the racket with a needle. Knitting time to tighten the thread at any time, do not let the thread appear loose, prepare a 5-meter long thread, thread the needle, and then wear it in the 8th hole, in the 8th hole on the opposite side, then in the back of the thread, and then wear it until the end of the 24th hole.

3. Open the badminton string, divide it into two sections, and call the left and right holes of the badminton racket the next hole, and the ones that extend to both sides are called the lower two holes and the lower three holes.

5. All operations are carried out synchronously on both sides until both sides are pierced to the lower nine holes, and the lines on both sides are threaded from the lower twelve holes to the upper eleven holes, and from the upper ten holes to the lower ten holes.

6. Thread the thread into the lower eight holes, the vertical line is completed, tie the knot and tie the thread from the upper six holes on the left side of the badminton racket, and thread the seven holes from the left to the upper seven holes on the right.

7. When wearing, cross up and down with the vertical line until it reaches the bottom seven holes, knot all the threads firmly, and cut off the excess threads.

8. Precautions: The thread should be tightened as much as possible, and the knot should be firm.

Badminton racket stringing and knotting method** is as follows:

1. The first step in the badminton racket stringing method is to measure the length of the string with the racket. The vertical string is pulled from the midpoint of the racket head to both sides to ensure that the left and right sides of the racket are deformed consistently, and the front is elastic and symmetrical. The vertical chord should be pierced through 1 hole on the paddle head, and the vertical chord should be worn and pulled symmetrically to both sides in turn.

Use a thread clip to the top of the frame to clamp the two middle lines. Then add pounds to pull the string.

2. Fix the line with another wire clamp and pull the pound The other one is also pulled, loosen the middle wire clamp, and move to the line that has just been pulled. Here's a detail. After the second line is drawn, you can directly pull the next line.

You can also re-weigh the first thread and adjust the thread clamp to the top of the frame to ensure that the left and right tensions are balanced. When re-weighing, avoid pulling over your head because the thread is already taut.

3. Turn the racket around, and then it is easier to pull the strings one by one on the left and right. When the lower 9 holes are pierced, you must jump to the lower 12 holes and then penetrate (in the meantime, jump two line holes), penetrate in the upper 11 holes, then penetrate from the upper 10 holes, penetrate from the lower 10 holes, jump back to the lower 8 holes and enter the knot, and finish. Special Attention:

The vertical 10th string is the last vertical string to be pulled, not the vertical 11th string.

4. Measure six and a half beats long as a horizontal line. The horizontal chord should be matched from the head of the frame, and the horizontal chord tension should be increased by 2 pounds on the basis of the vertical chord tension. When the racket is clamped, it is not allowed to use too much force to cause the racket frame to produce "leading deformation", otherwise the clamp must be readjusted, and the clamp must not be adjusted again in the process of pulling the string after the clamp is stabilized.

To wear the badminton string, you should first pull the vertical string from the midpoint of the racket head to both sides of the string, and the vertical string should be inserted from 1 hole in the racket head, and then symmetrically threaded and pulled to both sides in turn, and then jump back to the lower 8 holes after the lower 10 holes to enter the knot. Finally, the horizontal line is threaded from the head of the frame, and the horizontal line is pulled to the bottom of the frame one by one, and the horizontal chord tension can be increased by 2 pounds on the basis of the vertical chord tension.

1. The first thing to string a badminton racket is to measure the length of the string with a racket. The vertical line is eight beats long, and the vertical string before pulling the finch starts from the midpoint of the racket head and pulls the string evenly to both sides to ensure that the left and right sides of the racket are deformed consistently and elastically symmetrical.

2. The vertical chord should be penetrated through 1 hole on the paddle head, and the vertical chord should be worn and pulled symmetrically to both sides in turn. Use a thread clip to the top of the frame to clamp the two middle lines. Then add pounds to pull the string.

Fix the thread that pulls the pound with another clamp Pull the other one as well, loosen the middle clamp, and move it to the freshly pulled chain.

3. Turn the racket around and tighten the strings one by one on the left and right. After piercing the lower 9 holes, jump to the lower 12 holes and then penetrate it, penetrate it in the upper 11 holes, then penetrate it from the upper 10 holes, penetrate it from the lower 10 holes, jump back to the lower 8 holes and enter the knot, and the wide line of the vertical shed is worn.

4. The horizontal line should start from the head of the frame, measure six and a half beats long as the horizontal line, pull the horizontal line to the bottom of the frame one by one, and increase the horizontal chord pound by 2 pounds on the basis of the vertical chord tension.