Why doesn t the wireless router have a network setting?

You can connect the WAN port of the wireless router to the home network cable, connect the LAN port of the wireless router to the computer, open the router settings interface on the computer, set the router automatic dialing, and you can directly access the Internet. Anhui Telecom*** is at your service.

The general telecom cat does not need to be set up as a wireless router.

It needs to be set as shown in the figure below to connect the wire telecom cat without powering on, the router is powered on, turn on the computer, and set it according to the following methods1Open the browser, enter in the address bar, and press enter to enter the router management login page, as shown in the figure below (Note: the IP address of the router.

Generally, enter or enter the router management password, the default user name.

and password are "admin", click "login"3Click Setup Wizard in the left pane. Through the setup wizard we can set up the bandwidth of the router, 4

Click "Next" and select the type of network that our router is connected to. There are three types here: choose the first is PPPoE (ADSL Virtual Dialer), which is the most common PPPoE (ADSL Virtual Dialer), click "Next" to continue 5

Yes, set the wireless name and password if the router does not have a wireless network.

Skip this step, that is, the wireless network name of the router, you can set it yourself, and it is recommended to use a combination of letters and numbers SSID. Select the wireless security option, and the password is used to enter the verification when connecting to the wireless network, which can protect the wireless security of the router and prevent others from accessing the network. It is recommended to set the wireless name SSID to a combination of letters or numbers, and try not to use Chinese and special characters.

Avoid some wireless clients that do not support Chinese or special characters and cannot connect....for network security.

and the stability of the network, it is recommended to set a wireless password to prevent others from illegally accessing the network. After setting the "SSID and Security Password" of the wireless, click "Next, save and exit." To learn more about service offers, click on the "****" customer service 220 below to answer for you.

1. Enter the IP address of the router in the browser, enter the router password, and log in to the router.

2. Select the Internet setting option.

3. Select Static IP, set IP address, set Subnet Mask, Gateway to Gateway, and finally set local DNS.

4. Select the wireless settings tab, turn on wifi, and set the name and password of the wireless network.

5. Click the Advanced Settings tab, select the Intranet Settings option, and change the LAN port IP address to.

6. After saving the settings, connect the router to the Fiber Modem, and the wireless network of the Telecom Fiber Modem will be set up.

If there is no optical modem, you must have an optical port router, the entrance line is optical fiber, plug in the optical port, connect the network cable to the computer, log in to the router, configure the broadband account and password, and set the wifi password.

There may be some reasons why your wireless router has no signal:

If the wireless network and modem or external network cable fail, the network cable is loose, resulting in the external network network cable can not pass through the wireless router normally, thereby affecting the wireless network no signal, and the network cable connection of each device can be re-plugged by the wireless router modem external network cable;

If the wireless router modem is not working, check whether it is working and energized, if not, plug in the power supply cable of the device again;

Skip the wireless router and directly connect the modem to the computer broadband dial-up Internet, if the broadband dial-up is normally available, it is recommended to restore the wireless router to factory settings, re-set the Internet access parameters, and create a new wireless network;

If the modem cannot access the Internet with broadband dial-up, the fault may be caused by the modem or the external network. Disconnect the power to the modem for a few minutes before restarting, if the fault persists, call the local network operator to repair the network fault.

Dear users, hello:

For your question, it is recommended that you check:

1. Whether the WLAN on the wireless cat is bright, there is a WLAN button behind the wireless cat, which can control the turn of the wireless signal off and on.

2. Enter the wireless modem settings to check whether the wireless broadcast is turned off.

3. The restore hole behind the wireless cat can restore the factory settings of the cat, you can try it.

4. None of the above operations work, it is recommended that you call 10000 for repair.

Anhui Telecom will serve you wholeheartedly, our network hall is holding Tianyi mobile phone carnival activities, mobile phones are cheap in the whole network, during the event to buy mobile phones to send traffic, send phone bills, and participate in the lottery activities; At the same time, pay 100 and get 2 yuan free in the network hall, and you can also participate in the ** activity of smartphones and phone bills, welcome to check.

If you have any other questions, please come to the platform or Anhui Telecom's online business hall for consultation;

There is a "broadcast cancellation" in the wireless settings, how do you tick it? Ticking means that the name of the wireless network you set will not be broadcast, and the wifi terminal such as computers and mobile phones will not be able to find your wireless network, so you can only set the configuration file to let the terminal connect to the wireless network specified in the configuration file. The advantage of this method is that your wireless network name is not exposed to being connected by illegal intruders.

Try unchecking the box in front of "Broadcast Cancel".

Hello: It is recommended that you restart the cat and try again, if it still doesn't work, press and hold the recovery button for 5 seconds to recover.

If the network is connected, it doesn't matter, this is the management address of the device, and it doesn't affect your network...

If you still need to set it, don't connect it first, set it up one by one, and connect it... It would be nice to change the IP address

1. Open the browser, enter the general router address in the address bar or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

2. Find the network parameters --- LAN port settings in the management interface.

If you are afraid of conflicts, you can not connect the wireless cat first, only connect the wireless router, change the management IP of the wireless router to a different network segment from the cat.

Are you sure yours is a wireless cat? If it's OK, then your old cat can be retired. Replaced with a new one, both desktop and laptop can be used, but each requires dial-up Internet access. You don't need any settings, just sit in a seat.

If it's different, it's a conflict, I hope it can help you.