When setting up a wireless router, it always shows that the network cable is not plugged in, what is

The ADSL cat and the router are not connected, first solve the connection problem, the connection line between the router and the cat must be connected, the router is plugged into the WAN port, and then try. See if the crystal head socket light is on, if it is not on, change a network cable, or if there is a problem with the device port, try to change the port, try to clone the MAC in the router, clone the MAC of the router into the MAC of the computer you surf the Internet.

Wifi suddenly can't get onlineHow to fix it:1. The router is unstable: Some wireless routers and optical modems (broadband cats) have poor quality, and there will be a series of problems such as crashes after long-term operation.

2. Broadband failure: If the wifi at home can be connected to the Internet before, the problem of not being able to access the Internet suddenly appears. And the router and cat have been powered off and restarted, but it still can't be used after connecting to wifi.

In this case, it is very likely that there is a problem with the broadband line, or the broadband is in arrears.

4. Restricted networking: Almost all network cable routers have some functions that can be used to restrict mobile phones and computers from connecting to wifi to access the Internet. If the mobile phone and laptop are restricted, then there will be a problem of not being able to use it after connecting to wifi.

Summary. The reason is that the network cable is interrupted, especially the two network cables next to the circuit breaker are not properly plugged in, which causes the router application to not work properly, which causes the router to light up and show that the network cable is not plugged in. In order to solve this problem, first check the connection status of the network cable to ensure that the data transmission is normal; Secondly, if the router has many external devices, it may be due to a problem with the access device, and the status of the device needs to be rechecked. Finally, the router itself may fail and need to be reset.

Alternatively, it may be because the router's IP address is set incorrectly or disconnected from the network, and it needs to be modified and reconnected. In addition, it will be affected by other factors such as router settings, software, system defects, etc., you can try to update the router software to solve the problem.

Hello, the reason is that the network cable is interrupted, especially the two network cables next to the circuit breaker are not properly plugged in, resulting in the router application not working properly, resulting in the router lighting showing that the network cable is not plugged in. In order to solve this problem, first check the connection status of the network cable to ensure that the data transmission is normal; Secondly, if there are many external devices connected to the router hand-resistant device, it may be due to a problem with the access device, and the status of the device needs to be rechecked. Finally, the router itself may fail and need to be reset. In addition, it may also be due to the incorrect IP address setting of the Luchang server or the disconnection from the network, which needs to be modified and reconnected.

In addition, it will be affected by other factors such as router settings, software, system defects, etc., you can try to update the router software to solve the problem.

How to update your router.

2.Link your computer to the router, use a browser to access the management page of the router controller Xiang panel, in general, the router is the IP of the old delay or . 3.

Find the option to update the firmware and click Upload Firmware File. 4.Once the firmware upgrade is configured, you will usually be prompted to reboot your device, which is a must, to ensure that the router firmware is fully installed for it to work properly.

Updating your router's firmware can help your router get the latest performance optimizations and bug fixes, as well as improving the functionality of your device, as it is usually posted on the router's manufacturer**, or check out some blogs** for the latest firmware information. At the same time, it is especially reminded that during the router update process, do not interrupt the power supply of the device to avoid damage to the device.

Hello, I'm glad to answer for you, if the network cable light on the router flashes or doesn't light up, there may be the following reasons:1The network cable is not plugged in:

Check whether the network cable is plugged in, and it is recommended to plug and unplug it again to make sure that the plugs are in close contact. 2.Damaged network cable:

If the network cable is damaged or the plug is broken, it may cause poor signal transmission, and it is recommended to replace it with a new network cable. 3.Network port failure:

If the network port of the router fails, it may cause the network cable light to not light up, and the router needs to be repaired or replaced. 4.Power issues:

If the router is not properly connected to the power supply, it will also cause the network cable light to not light up, and you need to check whether the power supply of the router is normal. If none of the above methods can solve the problem, it is recommended to contact the router manufacturer or professional network technician for repair or troubleshooting.

The wireless network card is disabled, enable the wireless network card on the page that shows your local connection, that is, 1, click start2, click the control panel3, open the network connection4, find the wireless connection5, right-click "wireless connection" 6, click "enable", if it still can't be solved, it means that there is a problem with your wireless network card driver, reinstall the network card driver.

You don't have a network cable to the WAN port, just connect the network cable from the cat to the WAN port.

You must plug the network cable into the wireless router to set it up, and there are wiring and setting steps below.

Steps to install a wireless router.

1. Dial-up directly to access the Internet, and then be sure to disconnect the broadband connection.

2. Plug in the wireless router correctly, connect the cable that comes out of the broadband to the WLAN port, and take a network cable to connect one end to the 1234 random port, and one end to connect to the computer.

3. Open IE browser, enter in the address bar, and the pop-up user name and password are admin

4. Enter the wireless router interface, find the next step after the setup wizard - PPPoe (Internet mode) next - enter the broadband user name password and then the next step - (network parameters do not need to change) next - enter the SSID name (that is, the name you want to give your router, which can only be English letters and numbers) and PSK password (that is, the wifi wireless Internet connection password you want to set for your router), and then the next step - complete and restart the router, so that it is through.

5. If it is not connected, go to the network parameters - WLAN port settings to see if there is no connection there, if the broadband user name and password are wrong, there will be prompted when the connection is made.

I summarized it myself, I hope it can help you!