How Longines Rosewood watches adjust the time, adjust the date

Diwang Building, No. 5002, Shennan East Road, Luohu District, Shenzhen, Guangdong Province.

Shun Hing Plaza) Room 2513, 25th Floor] for your answer.

The correct way to adjust the date and time on the watch.

First, pull out the crown so that all the hands of the watch stop and enter the "time adjustment" state. At this time, adjust the time to 6 o'clock. (Don't damage the date module for one day or week).

Second, push the crown back to the position of "Adjust Date and Day". (At this point, the watch hand begins to rotate normally).

Third, adjust the date and day of the week to the day before the table day.

The fourth is an important step.

Please pull out the crown again to the "adjustment time" state when the hand stops and start adjusting time and rotate a hand clockwise (do not rotate a needle counterclockwise.) The time module is very damaged). At this time, the movement is soft, so adjust the time until the hand reaches about 12 o'clock, and the date and day of the week jump to the next day (watch day).

The pointer of the date jump description table indicates the time period of the morning of the adjustment table from now on. If you have adjusted the table just in the morning, adjust the table to the current correct time to fully restore the crown of the table.

Rotate the hands of the watch normally to exit the watch.

If the watch is adjusted in the afternoon, continue to adjust the time so that the clock passes 12 o'clock again. (At this time, the date and day of the week do not jump.) The current day of the table is also displayed.

The watch represents the time period of the afternoon of the watch. At this point, proceed to adjust the time of the watch to the correct time now.

Once in a while is not a big deal. Although the movement is fragile and easily damaged. But don't think of it as unbearable. After all, it is one of the three ace movements of EAT.

I don't know if you adjusted the time, how long it was, whether it was a few minutes, a few seconds. Or a few hours. If you turn back for a few hours.

At twelve o'clock in the evening, the mechanical watch automatically jumps the calendar. Therefore, adjusting the calendar during this time may cause damage to the gears. But the 2892 calibre is instantaneous.

So don't worry too much. Just pay attention next time. Adjust the time and date as much as possible in the morning.

Here's how to adjust the time and date on a Longines watch:

Material preparation: Longines Della Wiener.

1. Pull out the crown and stop all the hands of the watch to enter the "Adjust Time" state. At this time, adjust the time finger to 6 o'clock.

2. Push the crown back to the state of "Adjust Date and Day". Adjust the date and the day before the day before the date you adjust the schedule.

3. Pull out the crown again to the "Adjust Time" state when the hands stop, start to adjust the time, and let the hands turn clockwise.

4. At this time, the action needs to be soft, and the adjustment time is only round until the pointer indicates that it is close to about 12 o'clock, and the date and day of the week are found to jump to the next day, and this jump may occur when the hour hand passes 12 o'clock for the second time, it doesn't matter.

5. The hand of the date jump description table now begins to indicate the morning time period of the day you adjust the watch, if you happen to adjust the watch in the morning, then adjust the watch to the current precise time, and then push the crown back completely, the watch hand rotates normally, and the watch is over.

1.Take out your Longines watch.

Look at the calendar and time on the surface. 2.Turn the right knob to wind the watch and turn the original knob on one gear.

We can turn up the knob to adjust the date and the knob down to adjust the day. 3.You can adjust the time by pulling the knob one gear.

Longines watches. The date adjustment notes are as follows: 1Pull the handle out of the first gear to adjust the day and date, and pull out the second gear to adjust the time.

2.First, at 24 o'clock, the hand is in the second half of the circle. Not at 10:0 p.m

Adjust the date between 00 and 2:00 the next day, which may damage the date transmission gear. Set the time to 10 p.m

00-2:00, the sail slows down and starts to adjust the date with the knob. For example, today is the 26th, so we have to adjust the date to the 25th.

Then dial it out again and adjust the hand so that the date jumps to the 26th. Adjust it to the right time. 3.

If it is morning, it means that the hour hand is set less than one turn. 4.If it's afternoon, you need to make an extra turn so that the 24 o'clock hand is halfway there.

It is important to note that 24 o'clock is in line with the real time.

Hello, dear, the date adjustment method of Longines watch is as follows: first, when the second hand runs to the twelve o'clock position, pull out the shank and rotate clockwise to adjust the time. If there is no second, for the accuracy of the time, you can adjust the minute hand to the first two minutes of the time, and push it back to the handle after adjusting the time, and then if it is a Longines mechanical watch with a calendar, pull out the handle a little, you can adjust the day clockwise, adjust the date counterclockwise, pull the handle to the outermost, you can adjust the time, the specific operation is the same as the no calendar watch, there is not much difference, and the zero jump word of the Longines jujube leakage watch will not be as accurate as a quartz watch, It may be earlier or later, this is because the date and day of the week are a wheel to push Oh, I hope mine can help you, if you are satisfied with my service, please give a thumbs up, I wish you a happy life and smooth work!

Summary. Dear, I'm happy to answer for you, how to adjust the date of Longines watches, first, if it is a Longines mechanical watch, pull out the watch handle to adjust the day and date, pull out the second gear is to adjust the time. Second, first of all, at 24 o'clock, the watch hand is in the back half of the circle, and the time is from 10 o'clock to 2 o'clock in the evening, so that the date transmission gear may be damaged.

3. Then adjust the time to 10 p.m. to 2 p.m., and then start to dial the knob to adjust the date. For example, if it's the 26th, you have to adjust the date to the 25th, and then move it outwards to make the date jump to the 26th, and then to the correct time. Fourth, note that if it is in the morning, it means that the clock hand is less than one turn.

If it is afternoon, you need to turn more than 1 circle, so that the 24 o'clock hand is more than half, and you must pay attention to the 24 o'clock to match the real time. 5. If it is a Longines watch without a date, when the seconds run to 12 o'clock, pull out the handle and rotate clockwise to adjust the time. 6. If the Longines watch has no seconds, for the accuracy of the time, you can adjust the minute hand to the first two minutes of the time you want to adjust, and push it back to the handle after adjusting the time.

7. If it is a Longines watch with a calendar, pull out the handle a little, you can adjust the day clockwise, adjust the date counterclockwise, and pull the handle to the outermost, you can adjust the time, and the specific operation is the same as that of a non-calendar watch.

Dear, I'm happy to answer for you, how to adjust the date of Longines watches, first, if it is a Longines mechanical watch, pull out the watch handle to adjust the day and date, pull out the second gear is to adjust the time. Second, first of all, at 24 o'clock, the watch hand is in the back half of the circle, and the time is from 10 o'clock to 2 o'clock in the evening, so that the date transmission gear may be damaged. 3. Then adjust the time to 10 p.m. to 2 p.m., and then start to dial the knob to adjust the date.

For example, today is the 26th, you have to adjust the date to the 25th, and then dial it outwards to make the date jump to the 26th, and then adjust it to the correct time. Fourth, note that if it is in the morning, it means that the clock hand is less than one turn. If it is afternoon, you need to turn more than 1 circle, so that the 24 o'clock hand is more than half, and you must pay attention to the 24 o'clock to match the real time.

5. If it is a Longines watch without a date, when the seconds run to 12 o'clock, pull out the handle, rotate clockwise to take the circle, and adjust the time. 6. If the Longines watch has no seconds, for the accuracy of the time, you can adjust the minute hand to the first two minutes of the time you want to adjust, and push it back to the handle after adjusting the time. 7. If the Longines watch with a calendar collapses, pull out the handle a little, you can adjust the day clockwise, adjust the date counterclockwise, pull the handle to the outermost, you can adjust the time, and the specific operation is the same as that of a non-calendar watch.