Sick of it! Ask for a solution to the toilet not draining

Generally, the toilet does not drain because the outlet at the bottom is not aligned with the drain, and the screws at the bottom of the toilet bowl are broken, which will cause the toilet to drain through, or the toilet has been used for a long time, and it will scale on the inner wall, and in serious cases, it will block the vent of the toilet bowl and cause the toilet to drain slowly, and it is also possible that the cement or tile fragments fall into it during decoration or will affect the drainage.

First figure out the reason why the toilet does not drain, and then apply the spell to the symptoms:

Solution: 1. Water pressure dredging, tool-skin --- This method is to use the pressure of water pressure and skin --- to press the blocked foreign body into the sewer as a whole, and the operation first inject 2 3 or more water into the toilet, and then use the skin to resist the toilet drain, press hard, take out the skin and then repeat the press, generally need to repeat more than a dozen times to hear the sound of cooing, the toilet is passed, at most about 30 times can not be dredged, you need to consider other methods;

2. Stir up and dredge, the tool --- rotary toilet dredger--- this method is to use the shape of the red wine corkscrew, the foreign body is screwed out of the channel or crushed, the operation is very simple--- put the dredge into the drain as much as possible, and then rotate while applying inward pressure, of course, you also need to build in the toilet with a sufficient amount of water, so that it is convenient to dredge the water directly, if you can't rotate or the effect is very poor, it is likely that a large number of hair is blocked, and a large rotary dredge is needed;

3. Take out the dredging, the tool --- large dredging--- because the large rotary dredging device is higher and difficult to buy, so it is recommended to spend money to ask the dredging company to carry out, mainly for foreign bodies such as long hair that cannot be flushed down, they will take out the foreign body with the dredging device, and the toilet will naturally go into the water.

Reason why the replenishment toilet does not drain:

1. The toilet itself does not go into the water, or the water is not good--- this situation needs to be precautioned when buying and installing the toilet, basically follow two principles, the first try to buy the brand, the second is to touch the inner side of the toilet drain with your hand to see if it is glazed, if you dig it in by hand there is no smoothness, it is definitely unfavorable to the drain, easy to block, if it is very deep, it is also smooth, indicating that the glaze is better, which is conducive to the water;

2. The common blockage --- paper and feces is that the paper towel wraps the feces, resulting in the diameter of the blockage being larger than the diameter of the pipe, because the foreign objects in the toilet are soft, and the general use of a leather puff against the drain can be pressed continuously for more than a dozen to dozens of times.

3. Long hair blockage --- the most difficult way to deal with blockage, but it is easy to do with money, the normal 50-100 yuan dredging fee, there will be a professional sewer dredge with a large rotary toilet dredge to pull out foreign objects such as long hair directly, and the toilet will be solved without draining.

If you have this problem when you start using it, then you have to get rid of the toilet bowl to see if the drain level and the drain outlet are not compared when the toilet is installed. If it's good at the beginning, then it's necessary to dredge up, and the above two people are very comprehensive.

Buy a rubber bowl outside, about 4 yuan, go home and put water on your own to dredge up and down, a few more times on OK, and there is only a professional dredge person.

Go to the hardware store and buy a plucker, come back and dredge it yourself... If you really can't do it, you still have to hire a professional dredge, some money must be spent and can't be saved. . .

Unload the toilet and open the sewer, my house is so good, I don't know if it's completely good, anyway, my house's sewer is really blocked, and the toilet is definitely not good.

1、The water pressure is too lowThe reason is that the water pressure in the community is low, the floor is high, or the water valve is too small.

Water has impuritiesIn some areas, the water quality is poor or the water is not released first when it is installed.

Whether the float of the tank is faulty and whether the triangle valve is openOr whether the water hose is smooth or not may be the reason why the water tank does not go into the water.

The toilet does not drain the trick:

1. Pi is the most commonly used method, first put it on the toilet water outlet, press it down hard, form a vacuum, quickly dial it up, repeat it two or three times.

2. Flush the toilet with water, the specific method is to connect a large basin of water first, flush it down against the water outlet, it needs to be more than one meter, the strength should be greater, or if it is not effective, almost three basins of water can be.

3. Find a bent pipe, connect one end to the faucet, and insert the other end into the water outlet, after all are done, turn the faucet to the maximum, stir while flushing, and it can be solved in a few minutes.

The above content reference: Phoenix.com - What are the reasons why the toilet tank does not drain.

Analysis of various causes of poor toilet drainage: 1. Slight blockage of the toilet: Generally, the toilet blockage is caused by toilet paper or sanitary napkins, towel rags, etc., which can be dredged directly by using a pipe dredging machine or simple dredging tools.

2. Toilet hard object blockage: accidentally fall into plastic brushes, bottle caps, soap, combs and other hard objects when using. This kind of blockage is mild, you can directly use a pipe dredging machine or a simple dredging device to dredge directly, and when it is serious, you must disassemble the toilet to dredge, and this situation can only be completely solved by getting things out.

3. Aging and blockage of the toilet: The toilet has been used for a long time, it is inevitable that it will scale on the inner wall, and in serious cases, it will block the vent of the toilet and cause the toilet to drain slowly.

4. Toilet installation errors: generally divided into: the outlet at the bottom is not aligned with the drain outlet, the screw hole at the bottom of the toilet is completely sealed, which will cause the toilet drain to be unsmooth, and the water level of the toilet tank is not high enough to affect the flushing effect.

5. Squatting pit to toilet: some old houses are installed when building a squatting pit, and the bottom of the sewer pipe is a U-shaped waterproof elbow, when recreating the toilet, it is best to replace the bottom elbow with a direct bend, if it can't be replaced, then before installing the toilet, it is necessary to do a good job of cleaning up the bottom anti-water bend, and the installation is to avoid letting cement or tile fragments fall in. This kind of squatting toilet should be used with more care.

Hello answer, I have seen your question, and I am sorting out the answer, please wait for a while 1. If it is a toilet that has just been installed, it may be caused by improper installation of the toilet, and you need to find an installer to check the cause and deal with it.

2. It may be that the spring of the flush button is aged, there is no elasticity, and it cannot be pressed to the end, so it is not energetic when flushing.

Generally, the toilet does not drain because the outlet at the bottom is not aligned with the drain, and the screws at the bottom of the toilet bowl are broken, which will cause the toilet to drain through, or the toilet has been used for a long time, and it will scale on the inner wall, and in serious cases, it will block the vent of the toilet bowl and cause the toilet to drain slowly, and it is also possible that the cement or tile fragments fall into it during decoration or will affect the drainage.

It's a sewer blockage that needs to be cleared. Be careful not to throw hair into it, as it can easily hang on the wall of the tube.

The first possibility: whether the toilet pipe is blocked by foreign objects, and the second possibility: whether the toilet is displaced, whether the drain is aligned with the sewer pipe.

The third possibility: the ground before and after or left and right leveling is very different, it is recommended to use a level to measure, a little difference does not matter, too much difference with plastic packaging tape cut into a small piece of pad in a relatively low place.

What you need to prepare: rubber gloves, plastic bottles, scissors.

1. First prepare a plastic bottle for later use.

2. Then use scissors to cut off the bottom of the plastic bottle.

4. Next, hold the plastic bottle and poke the toilet drain repeatedly.

6. Finally, press the flush button to rinse and it is completed, as shown in the figure below.

Answer: I don't know if the toilet you installed is flush or siphon? If it is a straight flush type, it may be that there is no exhaust hole below the installation, and another is that if it is an old-fashioned building sewage pipe itself with an S bend, the newly installed toilet has an S bend inside, after installation, the following seal is too tight, the internal air can not form a backflow, drainage will be very difficult, if this is the case, then leave a gap or small hole at the bottom of the toilet and the ground connection, and there are generally two holes at the bottom of the toilet with installation bolts, this empty should not be sealed, In this case, if you flush the water, there will be air backflow, and it will definitely be enjoyable. If this situation occurs in the siphon toilet, it is most likely related to the structure of the toilet, and it is recommended to try a new toilet.

Generally, the toilet does not drain because the outlet at the bottom is not aligned with the drain, and the screws at the bottom of the toilet bowl are broken, which will cause the toilet to drain through, or the toilet has been used for a long time, and it will scale on the inner wall, and in serious cases, it will block the vent of the toilet bowl and cause the toilet to drain slowly, and it is also possible that the cement or tile fragments fall into it during decoration or will affect the drainage.

Looking for a professional sewer !!

Let's change it, I really can't find a sewer repairer.

Generally, just change the water, there is more sediment in the water, causing the toilet outlet filter to be blocked, you just need to remove the accessories of the water outlet and rinse it, I deal with it like this.

There are many reasons why the toilet won't drain, and here are some possible solutions:

1.Inspect the drains: Check the drains for blockages or cracks, which can be tested with a water gun to make sure there are no blockages or leaks in the pipes.

2.Check the drains: If there is no problem with the drains, then you need to check the drains for any blockages. Drain cleaners or tools such as toilet suction bowls can be used to remove blockages in the drain.

3.Replace drains: If drains are aged or damaged, they may need to be replaced.

4.Check the toilet drain valve: Make sure the drain valve is working properly and is not closed or damaged.

5.Check the toilet tank: Check whether the toilet tank is faulty or leaking.

If none of the above methods solve the problem, it is recommended to contact a professional cleaning company or toilet repairer to have it checked and repaired.

How to solve the problem of the toilet bowl not going down the state and the fierce water: 1. First of all, we use the leather to open the toilet, which is also one of the methods commonly used by modern people. The main thing is to put the leather against the water outlet of the toilet, and then press hard into the toilet pit for at least two minutes to form a vacuum inside the leather bowl, and then vigorously and quickly pull the leather up, and generally re-move two to three times to dredge.

2. Secondly, use water directly to flush the toilet. The specific method is to take a basin of water greater than or equal to 10 catties, and then flush it down against the toilet outlet, it should be noted that when doing this, it must be more than 1 meter, and the strength should be greater, otherwise it is useless. Generally speaking, about three basins of water will do the trick.

In addition, you can also find a pipe, the kind to be bent, connect one end to the bridge of the faucet with a large flow of water, and insert the other end into the outlet of the sewer, after completing this step, turn the faucet to a large size, let it stir vigorously while flushing, and it should be solved for a few minutes. 3. Of course, you can go to the market to buy some caustic soda and come back to the shed, boil water to melt the caustic soda, and then pour it into the toilet. After ten minutes, everything will be clear, and the method is relatively simple to use.

Hoses, toilet toilets, cola.

1. Hose

This is a more environmentally friendly and economical way to dredge, as long as the pipe is put into the pipe of the toilet, surrounded by a cloth, and then the faucet water is turned on to the maximum place, then the water pressure will become greater to flush the blocked place in the pipe, and bury the limb until it is dredged.

2. Toilet spirit

You can also buy a bottle of toilet cleaner, this method is more convenient, first pour hot water into the toilet, and then pour an appropriate amount of toilet cleaner into it, wait for half an hour, then you can use a leather mattress to squeeze and pull out the pipe mouth of the toilet, and the toilet will be passed, but this product is corrosive, so it is best to wear gloves when using, and you must be careful to pour it in.

3. Coke

Many people don't think that Coke can pass through the toilet, in fact, it's a bottle, first use scissors to cut off the bottom of its bottle mouth, and then put the bottle upside down at the pipe mouth, then you only need to hold the bottom end of the bottle, and pump it upward, and the toilet will be dredged.

Blocked toilet can be said to be a more common thing found at home, in fact, it is not terrible to be blocked, as long as you find the right way to deal with it, but the method must be used correctly, or it will not work. What should I do if the toilet is completely blocked and does not drain the water, you can use caustic soda to dredge it, first dissolve the alkali with hot water, and then pour it into the toilet, and wait for more than ten minutes, then the toilet will be unobstructed. You can also use steel wire to stir it, you can buy it with a front when you go to the hardware store, the length of the wire is 1 meter, 3 meters, and the turn can also be stretched in to stir, this method is more effective.