-
Steps to install a five-prong socket.
Tools Raw Materials:
Five-prong socket with switch.
Method Steps:
1. First of all, understand the five-pin socket with switch.
2. The five-pin socket is connected inside, we only need to connect the power supply. There are five binding posts on the back of the socket, labeled L, N, E, L1, L11 and L12. L is connected to the live wire, n is connected to the neutral wire, and E is the ground wire.
Other connections vary depending on the purpose of the outlet, and the connection method is different.
3. The use of a five-pin socket with a switch can actually be divided into three situations:
a, switch control socket.
b, switch control single control switch.
c, switch control dual control switch.
4. Wiring diagram of switch control socket.
5. The wiring diagram of the switch control single control switch.
-
The ground wire on the three-hole socket, the left is connected to the neutral wire, and the right is connected to the phase wire; The two-eye socket is connected to the neutral wire on the left and the phase wire on the right. To install securely, the fitting is tightened. Confirm that all wires are in full contact with the rear seat terminal heads of switches and sockets during installation.
The switch is mostly opened and closed with the hand in the opposite direction, the right hand is more than the left hand, generally on the left side of the door, and the door switch should be fluorescent. When decorating, pay attention to protect the panel of the switch and socket to prevent fouling. The switch should be 130 150cm from the ground, 15 20cm from the side of the door frame, and cannot be installed behind the door.
The position of the wall switch with wainscoting is at least above the top of the board, the height of the surface-mounted socket from the ground is not lower, the installation socket is not lower, and the kitchen and bathroom are determined separately. Do not install on the head of the bed or on the tabletop, and all switches should be closed in the same direction. Bathrooms and balconies should be equipped with splash-proof sockets or waterproof boxes, and bathtubs, faucets, and stovetops should not be installed, nor should they be installed within 20cm of the gas meter.
Household appliances strictly use two-hole sockets, bath bomb switch power is large, need to leave more space, often plug in and unplug electrical appliances can be used with switch sockets. Sockets without fixed load are counted as 1000 watts, and ordinary sockets use square millimeter copper core wire.
-
Does it depend on whether the switch controls the light or the socket?
You can refer to the following diagram to connect:
-
First of all, it is necessary to recognize the moving end and the immovable end of the single knife double-throw switch, the moving end is the so-called "knife", which should be connected to the incoming line of the power supply, that is, the end of the incoming call, and generally the end connected to the handle of the switch.
-
Question 1: How to install this kind of socket with switch? Figure 1 shows that the switch does not control the socket, but is also used to control the lamp, etc.
Figure 2 shows that the socket is controlled by a switch.
L is the phase (fire) wire, N is the middle (0) wire, and PE is the safety protection grounding wire.
Question 2: How to install the wall socket with switch Switch control socket: live wire to switch L, from switch L1 to socket L, neutral wire to N, ground wire to E.
Question 4: How to install the scion in the wall socket with a switch Step 1, switch control socket.
2. Switch and control electrical appliances (such as electric lights).
Question 5: How to install the lighting in the 5-hole socket with switch As shown in the figure, green is the L phase (fire) wire (red is generally used), blue is the N (0) line, and yellow (yellow and green lines should be used for the regular one) is the protective grounding PE wire.
Question 6: How to install the socket with a switch Switch answer control socket: live wire to switch L, from switch L1 to socket L, neutral wire to N, ground wire to E.
Refer to the diagram below. Question 7: How to install the socket with switch The original socket has three wires, L live wire, N neutral wire, and one is the ground wire. You connect the neutral wire and ground wire directly to the socket, connect the live wire to a hole of the switch, and connect a wire to the socket L position on another hole of the switch.
Question 9: How to wire the socket switch installed on the wall cleaning pants If you have a grounding wire, press into the grounding port, but there is generally no grounding wire stem, so the grounding port is empty. The switch is connected to the live wire, and L1 or L2 is connected to the control cable (this is when your lamp is connected without dual control).
-
Modern life is always indispensable to the existence of electricity, and the electrical appliances that flood the home will always feel that the switch and socket are not enough. In order to avoid the overload of switches and sockets, it is not negligible to arrange more sockets in many and decoration times; In addition, there are countless unsafe accidents caused by leakage at the switch socket, and it is very important to purchase high-quality switch sockets and install them safely. Today, Rilong will introduce you to the installation strategy of switch sockets.
1. How to choose a switch socket.
1. The brand is more secure.
Generally speaking, well-known brand switches and sockets will be dozens of dollars higher than ordinary ones, but for the sake of safety, these money should not be saved in home decoration. Most brands offer an effective warranty commitment to consumers.
2. Check the quality of the products.
Of course, it is important to check carefully when buying. When choosing Wang Xi, you can pick up the switch and insert the Chaling sedan seat, which requires a smooth surface and a hard and thick material; Then try it, the switch is required to be smooth and crisp, the socket must be equipped with a protective door, and a certain amount of strength is required when plugging and unplugging; At the same time, you can also ask about the internal materials of the switch and socket, and the high-quality products are made of phosphor bronze conductivity, and composite silver is used for electric shock.
2. Precautions for installing switches and sockets.
1. When installing the switch and socket, it should be after the carpenter and painter, and it may be full of dust. It is important to clean the bottom box, and any remaining dust can be wiped off with a damp cloth. This is also to prevent impurities from threatening the circuit and thus affecting the safety of Zhengzhou homes.
2. Pay attention to the length of the wire exposed in the bottom box for maintenance. Cut out a section of the core during installation, but don't hurt it. Coil the wire clockwise on the binding post corresponding to the switch or socket, and then tighten the indenter, requiring that the core is not exposed.
3. After connecting the wires, thread the wires out of the wire holes of the switch socket according to their respective positions, and press the wires firmly according to the wiring requirements. Finally, attach the switch socket to the plastic table, align it and fix it firmly with screws, and cover the decorative plate.
1. Switch control socket. Firewire connector L1, switch L and socket L are connected with **, the neutral wire is connected to socket N, and the ground wire is connected to socket E (grounding symbol). >>>More
Normally, the situation that is often seen in life is basically the socket on the top or side of the bedside table, because in this way, the charging equipment can be placed on the bedside table when in use. However, it was found that some netizens on the Internet think that the socket should be set on the back of the bedside table, and they think that the socket appears on the top of the bedside table, which not only affects the appearance, but is also particularly easy to be touched when in use, so they think it is best to put it underneath. >>>More
The bottom edge of the door switch box is 70mm from the ground, and the side margin must be 70mm away from the door sleeve line. The same type of switch installed in parallel is 1mm away from the horizontal ground height, and the switch in special position (bedside switch, etc.) is installed according to the owner's requirements, and the switch of the same horizontal line < 5mm. >>>More
EPL wireless kinetic energy switch, no battery, no wires, no need to chisel the wall buried pipe wiring, installation is not limited by wall materials, easy to achieve dual control and multiple control. You can also use the mobile app or intelligent voice control to achieve dimming and color adjustment, and the smart life scene can be easily enjoyed.
Switch. Receptacle.
It is common in our lives, many homes, offices. >>>More