How to connect the switch with the socket, how to connect the socket with the switch

1. Switch control socket. Firewire connector L1, switch L and socket L are connected with **, the neutral wire is connected to socket N, and the ground wire is connected to socket E (grounding symbol).

2. Switch and control the light. The socket should always be open. With wire connection socket L, switch L, socket L connection **, neutral wire connection socket N, ground wire connection socket E (grounding symbol). Switch L1 is connected to the positive pole of the lamp with the control wire, and socket N is connected to the negative pole of the lamp with the neutral wire.

3. Use a short section of wire, connect L1 and L, the neutral wire (green wire) into the N-line post of the new socket, and the live wire (red wire) into the COM line post of the socket.

1. Switch with socket wiring method.

1. Single-control single-open switch connection method. The structure of single control and single opening is very simple, so the connection method is relatively simple, you need to use the red wire to connect the L binding post behind the socket, and then the blue wire is connected to L1, so it is completed.

2. Single-open five-hole socket connection method. When installing the switch socket, it is best to set aside a section of the wire in the socket box after all the work is completed, so as to facilitate future maintenance, and then wrap the wire around the binding post, do not leak the wire core, and finally fix the socket on the wall, and then screw it on.

3. Single-open three-hole socket wiring method. In fact, the three-hole and five-hole ones are very similar, but there are also some differences, that is, there are some differences in some binding posts, and there are some differences in the problems paid attention to when connecting, because the wiring in the socket of these two holes is different.

Second, the installation skills of switch sockets.

1. First of all, the socket cannot be installed on the tile piece, and the waist line cannot be installed.

2. The tile can not be destroyed when the switch and socket is installed, and it should be installed in the middle of the tile as much as possible, otherwise it may not be too firm and easy to fall off.

3. When the bottom box of the socket is punched in the tile, the round hole can not be opened, and the edge of the bottom box is best to be flat with the tile, so that the screw will not be very long when it is installed in the future, and it is also to ensure the convenience of installing the socket in the future.

4. Of course, it is not possible to install a socket in the bathroom, because there will always be splashing water in the bathroom, so you must install the waterproof socket switch.

The general sockets are installed on the wall, and some jacks are also relatively high, which is also to ensure the safety of children, because children are not sensible, so it is inevitable that there will be curiosity to drive them to touch those switches and sockets, so parents must take protective measures, sometimes it is inevitable that the wires will burn out, at this time, the general people do not want to ask for labor anymore, so they simply do it themselves, so they must understand how to wire these socket switches.

How to wire the socket with a switch, learn to do it yourself without asking for help.

1. Now many switches have sockets, and when this kind of switch socket is wired, because the bottom box has been installed and arranged in place, but a lot of dust accumulates there. Clean the bottom box first, then dry the surface with a damp cloth. Send the old group to wait until it is dry, cut out a certain length of the wire reserved in the box, strip the wire for a distance with wire strippers, and coil it on the corresponding binding post of the switch in a clockwise direction, and the core should not be exposed.

2. Then distinguish the live wire by the electric pen, connect it to the hole marked with L in the two holes of the switch, and then connect the insulated wire from the other hole and connect it to the L hole in the three holes of the socket. Ensure that the wiring is firm, the neutral wire is connected to the N wiring port in the three holes of the socket, the ground wire is connected to the E binding post, and then the base is wrapped with insulating tape to prevent loosening. 3. When all the wires are threaded out of the plastic outlet hole, they are fixed on the socket box with screws.

The socket is straightened and fixed with screws, and the decorative plate can be covered.

Do you want to switch the control socket or the switch and socket separately.

General 1 open 5 holes.

The incoming line is A1, and the outgoing line is L1 and LB (dual control).

Then the non-porous side shows L2

n There is also the neutral line interface.

If you select the outlet you want to switch on and off.

You choose. A1 incoming line.

L1 outlet. L1 and L2 are connected by wires.

Then n is connected to the neutral line.

The ground wire can be left alone; Select and you complete the solution of the switch control socket;

If it is controlled separately.

That is through the A1 line.

L1 outlet to control your lights.

Then A1 and L2 are connected with wires.

The n-line is the neutral line.

So that the socket has electricity.

Do not interfere with each other. The downside, though, is that your switch load is right behind the switch; But with this kind of connection, you can also connect a single live wire to L2

Then n out of the line.

Then it is truly non-interfering and your lights can be connected to the front of the switch.

The wiring method of the switch with socket is as follows:

Material preparation: switches, wires, etc.

1. One open three-hole wiring with switch socket.

2. Wiring diagram of dual control lights (red is the igneous rock shielding line, green is the zero line, and blue is the grounding wire Wang Bend).

3. Socket wiring diagram of double switch five holes (2 holes and 3 holes).

4. Double 5-hole switch wiring. Sleepy dates are stuffy.

5. Open five holes (switch the two head control lights connected to the fire wire; Socket L is connected to the live wire, N is connected to the neutral wire, and E is connected to the ground wire).