How to adjust the computer when the embroidery machine is broken? Computerized embroidery machine tr

First of all, check whether the disconnection detection is set in the computer parameters.

Wire disconnection detection is set in the computer parameters, but all machine heads are still not detected after disconnection.

Check the motherboard indicator, 91 model D29, D3095 model D16, D1807 model L35, model XJIA, DXQD. 18 28 models check xija, dxqd. When the machine is running normally, D29, D16, L35, Xija these indicators should flash, D30, D18, L36 should be always on, and DXQD lights should be flashing.

If the above indicator status is incorrect, there is a problem with the motherboard and needs to be replaced.

When the above indicator light status is right, 91 95 model check model check A8, 08 model check model check CZ5812 socket, to the last machine head disconnection detection board socket, three-digit disconnection detection board is CZ1, two-digit disconnection detection board is CZ011, the corresponding connection is connected, if not, prove that the signal is not transmitted to the disconnection detection board, need to be repaired to make it connected.

The three-position disconnection detection board checks the CZ1 signal socket, and the two-position disconnection detection board checks whether the CZ011 signal socket is plugged in.

172 degrees is the lowest point of the needle. The needle hole just exposes the inner circle of the twistlock.

196 degree adjustment of the position of the twistlock and the needle, and the tip of the twistlock is off the needle.

The needle cannot rub the presser foot.

The needle should not be used to rub the edge of the needleboard.

The needleboard holes must not have burrs.

The crossing part needs to be smooth, and the cable should be smooth.

When making plates, short stitches are filtered out.

Hello. The computerized embroidery machine always drops the thread.

First of all, the needle is dropped because of the tangent.

The noodle line is short. In this way, as soon as the needle is struck, the thread falls out of the pinhole.

Find the cause, and you solve the cause.

Set it up in the computer first, make the noodle line longer, and loosen the noodle line.

Others try again at the end. Adjustment of the knife position is required.

Computer embroidery plate making, training computer embroidery plate making, computer embroidery machine maintenance, I am very professional. Any questions you have are always available.

Thank you. <>

The starting speed is slow, two more stitches are pricked at the start, and the top of the wire cap cannot be adjusted too tightly.

Summary. There are two situations of broken thread of computerized embroidery machine, one is regular broken thread, and the other is irregular broken thread.

Causes and treatment of regular disconnection:

1. The gap between the needle and the hook is not right, and the needle position is too high or too low, so it needs to be readjusted.

2. There are burrs in the pinhole and needle plate hole, burr in the rotary hook, and burr in the positioning hook.

3. The part of the wire crossing is not smooth, including the clamping plate, the clamping screw, the take-up rod hole, the upper and lower wire crossing frames, etc., all unsmooth or burrs should be smoothed or replaced.

4. The needle is reversed, and it needs to be re-installed correctly, the needle tip is damaged, the needle is stained with glue, and the needle is replaced.

5. If the pick-up cam is damaged, replace the pick-up cam.

6. The rotary hook shaft is channeled.

7. There are scratches and damage on the surface of the hook crossing the line.

Causes and treatment of irregular disconnection:

1. The ambient humidity is too high, the line is damp, dehumidifying, and changing the line.

2. The pattern is unreasonable. Revision.

3. The quality of the thread does not meet the requirements, the installation of the thread does not meet the requirements, the embroidery thread is too thick, and the needle specifications do not match. Changeover and reload.

4. The moving frame curve and moving frame angle are unreasonable, and the computer parameters are adjusted.

5. There is a gap between the upper and lower shaft transmissions or the shaft is broken, which causes the head and the rotary hook to be out of sync. Check the gearbox and adjust the chain tightness or gearbox timing belt.

6. The surface of the embroidery thread is rough. Add silicone oil to the surface of the embroidery thread.

Computerized embroidery machine trimming thread dropping

There are two situations of broken thread of computerized embroidery machine, one is regular broken thread, and the other is irregular broken thread. Causes and treatment of regular wire breakage: 1. The gap between the needle and the hook is wrong, and the needle position is too high or too low, which needs to be readjusted.

2. There are burrs in the pinholes and needleboard holes of the machine, burrs in the rotary hook, and burrs in the positioning hook and cover. 3. The part of the wire crossing is not smooth, including the clamping plate, the clamping screw, the take-up rod hole, the upper and lower wire crossing frames, etc., all unsmooth or burrs should be smoothed or replaced. 4. The needle is reversed, and it needs to be re-installed correctly, the needle tip is damaged, the needle is stained with glue, and the draft is needle-resistant.

5. If the pick-up cam is damaged, replace the pick-up cam. 6. The rotary hook shaft is channeled. 7. There are scratches and damage on the surface of the hook crossing the line.

Causes and treatment of irregular disconnection: 1. The ambient humidity is too high, the line is damp, dehumidified, and the new line is replaced. 2. The pattern is unreasonable.

Revision. 3. The quality of the thread does not meet the requirements, the installation of the thread does not meet the requirements, the embroidery thread is too thick, and the needle specifications do not match. Changeover and reload.

4. The moving frame curve argument and the moving frame angle are unreasonable, and the computer parameters are adjusted. 5. There is a gap between the upper and lower shaft transmissions or the shaft is broken, which causes the head and the rotary hook to be out of sync. Check the gearbox and adjust the chain tightness or gearbox timing belt.

6. The surface of the embroidery thread is rough. Add silicone oil to the surface of the embroidery thread.

When the car is disconnected or carried, and the machine is all red light. How to solve Wang Yu's decision: turn on the red light and check if there is a problem with the motherboard. Disconnect, check the trapped segment potentiometer, and consider replacing it if necessary.

Hello dear, what is the reason why the needle of the computer embroidery machine always drops: 1The buckle electromagnet on the side of the shuttle bed is damaged, or the position of the buckle hook is offset 2

The noodle line is too tightThe machine parameters in the computer can be adjusted (100 to -100), the larger the parameters, the shorter the tangent wax balance, it is easy to drop the thread embroidery machine, also known as the computer embroidery machine, it is the most advanced embroidery machinery in contemporary times, it can make the traditional hand embroidery get high speed, high efficiency of the bucket, and can also achieve manual embroidery can not be achieved"Multi-layered, multi-functional, unified and perfect"requirements. It is a kind of mechanical and electrical product that embodies a variety of high-tech technologies.

With the replacement of manual embroidery by computerized embroidery, computerized embroidery machines will also become the main machine in the embroidery industry.

First of all, you have to understand what is the reason for the unfixed drop. to find a solution to the problem.

This situation occurs because the noodle thread is cut short during the tangent, and the noodle thread comes out of the pinhole after the needle is removed.

To solve this problem, you have to make the noodle line longer when tangential.

You can first set it up in your computer and make the tangent longer.

Then, when the machine starts embroidering, it takes a few stitches slowly.

In the end, if it doesn't work, you'll have to adjust the fork.

Computer embroidery plate making, training computer embroidery plate making, computer embroidery machine maintenance, I am very professional, any questions can be provided to you at any time to provide answers.

Thank you. <>

After the computer afternoon embroidery machine trimming, there is always a drop in the thread, at this time we must follow the formal process, the part that is not easy to fix is skillfully fixed on the designated part, so that it will be more convenient to use, and avoid the above situation.

Hello. The computerized embroidery machine is old and the thread is broken.

First of all, the thread breakage of the embroidery machine is generally caused by fluffing.

In this case, there is usually a problem with the fit of the needle and the twistlock.

Or there is too much gap in the machine parts.

Thank you. <>