Which brother knows how to use the electric constant temperature incubator

Turn on the power, press the setting button to automatically adjust the temperature to your required temperature, up and down about 2 degrees, other values do not need to be changed, just wait for it to automatically generate temperature. There is a built-in thermometer to see how much the temperature value of the display screen is different from the value on the thermometer, and it can be used if it is in a normal state within the setting range. If it is not used for a long time, it should be turned on for half a day every month to ensure the normal operation of the machine and maintain it.

The maximum temperature of the incubator is 20 degrees.

The automatic thermostat type temperature control device is mostly used in the "metal sheet type". That is, a kind of metal sheet with a large coefficient of thermal expansion is used to make a spiral. One end of the metal sheet is fixed to the wall of the chamber, and the other end is equipped with movable contacts.

The two contacts are closed at room temperature. After the power is turned on, the temperature in the box rises, the metal sheet fixed here expands by heat, and the bending changes, so that the contact at the other end leaves, cuts off the circuit, stops heating, and the temperature of the ante blade drops. down to a certain level.

The spiral metal sheet is restored to its original state, and the two contacts are in contact again, and the circuit is connected and heated, so that the circuit is turned on and off to keep the constant temperature in the box.

Principle:

1. The water jacket type heats the liquid layer wrapped around the periphery through the stuffy ridge, and then heats the inside, which is slower, but can maintain a constant internal temperature for a long time and maintain the stable culture of the sample.

2. The electric heating film type directly heats the box through the electric heating film attached to the inner wall, and the heating is relatively rapid, and the interior can reach the required temperature in a short time.

3. Most of the computer intelligent control types use the microcomputer PID controller as the control unit, the thermal element as the thermometer, and the digital display of the set value and the measured value, so as to constitute a complete control system.

In the case of a constant temperature incubator, it is usually up to 60 degrees Celsius.

Constant temperature Fu Jingzhi culture manuscript buried box is generally the most lacking high temperature is 60 Suzhou Haisiyuan.

Incubator.

The electric constant temperature incubator adopts the method of electric heating, and heats the dry zone in the box through the heating tube, which is suitable for ordinary bacterial culture and closed cell culture, and is often used for the pre-heating of equipment and reagents related to cell culture. It is mainly composed of several parts, such as box, heater, blower and temperature controller.

The working principle of an electrically heated incubator.

The electric heating constant temperature incubator controls the power on time of the electric heating tube to keep the temperature constant at a certain value, and when the temperature is lower than this set temperature value, the electric heating tube starts to heat; When the temperature is higher than this set temperature, the electric heating tube stops heating.

In order to ensure that the internal temperature of the electric heating incubator is uniform, according to the size of the box, off-core fans with different powers will be installed near the electric heating tube, so that the temperature of the electric heating tube will be evenly and quickly distributed to the inside of the box. Through the internal air flow circulation of the box, the temperature is constant.

The working principle of an electrically heated incubator. jpg

The purpose of the electrically heated constant temperature incubator.

The electric constant temperature incubator is a small equipment that integrates heating, which is an ideal choice for agriculture and forestry, colleges and universities, and scientific research units. The electric constant temperature incubator is widely used in the seedling, germination, growth test, and plant growth of seeds, and can also be used for the storage and constant temperature test of other substances. The electrically heated incubator can be used as a customized incubator for E. coli culture in a food factory.

Features of the electrically heated incubator.

1. The electric heating constant temperature incubator adopts the structure of natural convection gas type, cold air enters from the bottom air inlet hole, rises from the convection space on the left and right sides after electric heating, and enters the inner chamber from the small holes of the flower plate on the left and right sides of the inner tank, and then escapes from the tuyere of the wind top, and the temperature of the inner chamber is uniform.

2. The shell of the electric constant temperature incubator is generally welded with thin steel plates, and the thermal insulation layer is filled with Hui insulation material to maintain the good thermal insulation performance of the box.

3. The outer door of the electric heating constant temperature incubator is a thin steel plate, and a double-glazed observation window is generally used to facilitate intuitive observation of the test situation, the handle is integrated with the locking device, and the hinge device opens and closes flexibly. The outer door and the box door frame are sealed with silicone rubber to prevent hot gas from escaping. The electrical parts are installed in the space on the left side of the box for easy maintenance and replacement.

4. The temperature control system of the electric constant temperature incubator uses a digital display thermometer, and uses a high-stability thermistor as a sensing reed temperature element, which has the advantages of sensitive temperature, small thermal inertia, high precision, stable performance, etc., and the digital display thermostat is easy to monitor and read due to the intuitive digital display, and it is also clearly visible in dark places.

Summary. Hello, the use of the electric constant temperature incubator is as follows: 1. Before the incubator is powered on, you need to check the electrical performance of the electric constant temperature incubator, and check whether there is a power failure or leakage.

2. Secondly, after the electric constant temperature incubator is ready, you can put in the sample, close the door of the box, and adjust the exhaust valve appropriately. 3. Turn off the power supply, go to the opening, and press the button under the instrument. Set the required temperature, the green indicator light of the meter is on, start heating, as the temperature rises, the incubator window displays the temperature measurement, when the set value is reached, the red light of the incubator is on, stop heating.

Hello, the use of the electric constant temperature incubator is as follows: 1. Before the culture of the rapid imitation box is energized, you need to check the electrical performance of the electric constant temperature incubator, and check whether there is a power failure or leakage. 2. Secondly, after the electric constant temperature incubator is ready, you can put in the sample, close the door of the box, and adjust the exhaust valve appropriately.

3. Turn off the power supply, go to the opening, and press the button under the instrument. Set the required temperature, the green indicator light of the instrument is on, start heating, as the temperature rises, the incubator window shows the temperature leakage measurement value, when the set value is reached, the red light of the incubator instrument is on, stop adding jujube heat. <>

Hello, when the temperature is lower than the set value, the meter turns to the green light again, and the temperature rises again, and the cycle repeats itself, so that the temperature is kept at the temperature set value with a smile. When the time of the use of zero or simply move to the adjustment function of the incubator instrument when touching the skin, you will have to according to the size of the load heating power, resulting in the measured value higher or lower than the set net difference correction, adjust the potentiometer, you can eliminate the deviation, to adapt to different situations. <>

Hello dry friends, it should be noted that when the temperature of the incubator reaches a constant temperature, its temperature tends to continue to rise, which is the influence of waste heat, and this phenomenon can be stable after about 90min. Moreover, the items in the incubator should not be overcrowded, and the hot and cold air should not be blocked, so as to maintain the uniformity of the temperature in the incubator.

I didn't <> blind

Hello, dear, I am glad to answer for you, how to use the electric constant temperature incubator? The method of using an electrically heated constant temperature incubator is as follows: first, place the incubator in a dry, ventilated, and dust-free environment to ensure that the surrounding environment temperature is stable; Secondly, put the sample or petri dish into the incubator, set the required temperature, humidity, time and other parameters to start the power; Finally, adjust and change the temperature, humidity and other parameters in time according to the experimental requirements, and at the same time, pay attention to the daily maintenance and cleaning of the equipment to ensure the normal operation and service life of the equipment.

In the process of using the electric constant temperature incubator, it is necessary to strictly abide by the instructions and safety specifications to avoid the occurrence of operation errors and safety accidents. I hope this service can help you, thank you for your consultation, and I wish you all the best!

Use the how-to.

Operators need to read the instructions carefully to understand and be familiar with the functions of the incubator before turning on the power.

Turn on the power and press the power switch, and the power indicator will be on.

Set the temperature controller to the user's desired set temperature (this value should be 50C above room temperature).

When the incubator shows that the temperature reaches the set temperature, the heating is interrupted, the heating indicator is off, and the temperature can remain stable after 90 minutes of power-on at the standard ambient temperature, such as the real-time temperature in the incubator exceeds the set upper limit alarm temperature (factory set to 5), the thermostat temperature tracking alarm indicator lights up, and the heater power supply is automatically cut off at the same time.

For example, when the glass door is opened to take samples, the heater and circulating fan will stop working, and when the glass door is closed, the heater and fan can operate normally, so as to avoid the pollution of the culture and the overshoot of temperature.

Precautions and maintenance repairs.

The instrument should not be used under the conditions of high voltage, high current and strong magnetic field, so as to avoid interfering with the temperature controller and the risk of electric shock.

Electroplating parts and surface paint, should be kept clean frequently, if not used for a long time, should be coated with neutral grease or petroleum jelly on the electroplating parts to prevent corrosion, the incubator outside the plastic film dust cover to put the incubator in the drying room, so as not to damage the thermostat by moisture.

This product has been strictly debugged before leaving the factory, and the thermostat menu setting data should not be modified at will.

The shell of the culture sail hail shouting box must be effectively grounded to ensure the safety of use.

Do not place flammable and explosive materials for limb heating to prevent danger.

Do not place items with high acid and alkali to prevent the box from rotting.

Summary. Hello, we are happy to answer that measuring and setting up an electrically heated incubator are two different processes. Measurement refers to the real-time monitoring and reading of the current internal temperature of the incubator, usually through a temperature sensor.

Inside the incubator there is usually a control panel where you can see the current temperature value and the options for setting the target temperature. Setting refers to setting the required target temperature on the control panel of the incubator according to the needs of the experiment. In the setting process, it is necessary to set the required temperature, time and other parameters according to the experimental requirements, and usually the temperature needs to be gradually raised and lowered to ensure the accuracy and stability of the research or experiment.

Hello, we are happy to answer that the measurement and setting of an electric thermostatic incubator are two different processes. Measurement refers to the real-time monitoring and reading of the current internal temperature of the incubator, usually through a temperature sensor. Inside the incubator there is usually a control panel where you can see the current temperature value and the options for setting the target temperature.

The setting refers to setting the required target temperature on the incubator control panel according to the experimental needs. In the setting process, it is necessary to set the required temperature, time and other parameters according to the experimental requirements, and it is usually necessary to gradually raise and lower the temperature to ensure the accuracy and stability of the research or experiment. Hope mine can help you.

Can you elaborate on that a little bit more?

Hello, the measurement and setting of the electric thermostat incubator are two different processes, it is worth noting that in order to ensure the accuracy and reliability of the experimental results, the temperature measurement and setting of the thermostat should be cleared, calibrated and debugged by professional engineers to avoid errors. At the same time, it is necessary to follow the correct operation specifications during use, and pay attention to safety protection and maintenance.

Hello dear and very happy to serve you <>

Let you wait for a long time, the reasons and solutions are as follows: 1. Check whether the constant temperature and humidity incubator identification plate is in the state of inactivation or operation, check the use record of the incubator, if it is normal, then hang the operation identification to the incubator, and you can operate. 2. Fill the water tank at the back of the main incubator with water.

3. Turn on the power switch on the control panel of the incubator, and the indicator light on the switch is on, and the temperature control instrument and humidity control instrument of the incubator are displayed: The "PV" line of the temperature control instrument (red) shows the measured value of the dry-bulb temperature, that is, the actual temperature in the incubator, and the "SV" line (green) shows the test temperature set value; The "PV" line (red) of the humidity control instrument shows the wet-bulb temperature measurement, which is the actual temperature inside the incubator, and the "SV" line (green) shows the wet-bulb temperature setpoint. 4. Temperature and humidity setting

Press the function key on the temperature control instrument first, at this time, the temperature value of the "SV" line will flash, and then modify the temperature set value by pressing the "" button of the temperature control instrument to make the temperature value of the "SV" line reach the temperature value required for the test, and then press "SET" to confirm. When the temperature is set, according to the relative humidity of a dry bulb temperature required for the test, check the difference corresponding to the data in the "relative humidity checklist", and then subtract the difference from the dry bulb temperature, that is, to obtain the set value of the humidity control instrument, and press the function key on the humidity instrument, at this time, the temperature value of the "SV" line will flash, and then modify the temperature set value by pressing the "" key of the temperature control instrument, so that the temperature value of the "SV" line reaches the temperature value required by the test, and then press "SET" to confirm. 5. Turn on the heating switch of the incubator, turn on the heating, the blower motor in the incubator will run, and the temperature control instrument will start to control the heater to work.

6. When the measured value of dry-bulb temperature reaches or approaches the set value of dry-bulb temperature, turn on the humidification switch, and the humidity control instrument begins to control the humidifier to work. 7. Turn on the refrigerator: After the temperature and humidity setting is completed, you can decide whether to turn on the refrigerator according to the test temperature, humidity and ambient temperature and humidity.

The general principle is that the test temperature is higher than the ambient temperature of 10 or more, and the test relative humidity is higher than the ambient humidity, the refrigerator can not be turned on. If the test temperature is lower than the ambient temperature, the refrigerator is turned on when the test relative humidity is lower than the ambient humidity. 8. After the test temperature is fully stabilized, if the temperature display value of the incubator does not reach the required temperature setting value, the temperature setting value can be slightly increased, and the temperature setting value can be slightly lowered.

9. According to the actual needs, whether to observe the sample, decide whether to turn on the lighting, and do not turn on the lighting under normal circumstances. 10. The incubator has its own temperature limiting device, when the test temperature reaches about 60, the heating power supply will be automatically cut off, and the over-temperature indicator will be on at this time. 11. After the constant temperature and humidity incubator is used, the use record should be filled in.