What is the reason why the solar sewer pipe keeps dripping?

The valve is not closed tightly when it is aging.

When the water is flowing, you turn on the nozzle, if the nozzle does not run after the nozzle, that is, when you are full of water, the water expands when heated, and the volume increases, and it overflows from the overflow.

The phenomenon you describe seems to be impossible, how can the water in the tank not flow when it is not enough to flow from the overflow pipe? Does the water flow all the time?

That is, the installer connected the pipeline in reverse, because the overflow port is high, and the bottom of the drain outlet should be they put the overflow outlet as the downstream, and the drain as the overflow port is connected, the reason is that the overflow port does not have a valve, you.

As soon as water is poured from a high place, it will flow out from the bottom.

If the overflow and the drain are both on the underside of the solar (perpendicular under the bucket), the first is that it is reversed, and the second is a pipe with a limited water level in the bucket at the overflow port, and that pipe is either broken or not there, so you fill it and it will not survive at all.

Looking at your introduction, the water supply and return water on the roof of your building must be very long (the part from the pipe well to the solar energy), it is recommended to use a water temperature and water level meter with automatic water supply, so as to save water and clean the room. Checking for water leakage is also very simple, add a ball valve to the inlet and outlet of the solar energy, close it after filling the water, if the solar water is still full after a day, it is a broken pipe, otherwise it is a solar leakage.

Check your solar water valve, if the ball valve core is damaged and not closed tightly, if it is a solar valve, the ceramic core can be replaced if the ceramic core is worn.

Minor problems can be solved by a plumber.

It may be that the water pipe on the solar upstairs is broken and leaking, and you can contact the local maintenance personnel to come to the door.

It should be that the upper and lower water pipes are cracked, and it is recommended that you replace them and try again.

The sun is sunny and the sewer pipe has been flowing what Harada.

Problems with solar sewer control valves.

Summary. 1. Due to the good sunlight and high water temperature of the water tank, the evaporated water vapor condenses into water and flows down, which is a normal phenomenon.

2. The valve on the water is not closed tightly, which always leads to slow water supply, you can try to close the main valve at home and then turn on a cold faucet.

3. It may be a problem with the small leather pad on the return pipe in the water tank.

4. The solar overflow pipe has been overflowing outward: it is the water that flows when the water is full. Indicates that the system is still adding water. It may be that the water filling valve is out of order.

Why does the overflow pipe come out of the water if the solar energy does not get water.

1. Due to the good sunlight and the high temperature of the water in the tank, the evaporated water vapor condenses into water, and the one that flows down belongs to the normal limb royal elephant. 2. The valve of the water supply is not closed tightly, and the water is always slowly supplied due to the hunger wheel, you can try to close the main valve at home and then open a cold water faucet. 3. It may be a problem with the small leather pad on the return pipe in the water tank.

4. The solar overflow pipe has been overflowing outward: it is the water that flows when the water is full. Indicates that the system is still adding water.

It may be that the water filling valve has failed.

Let's take a look at the reason.

There are two possible things that could go wrong

1) The temperature probe is bad.

2) The float is bad.

Reason: (1) If the solar energy is equipped with a controller, it is a problem with the temperature sensing probe.

2) If the solar energy is brought to the water with a float, the float should be bad and not dead.

How it works. Sunlight shines through the first layer of glass of the heat absorbing tube to the black heat absorbing layer of the second layer of glass, absorbing the heat of sunlight energy, because the two layers of glass are vacuum insulation, the heat transfer will be greatly reduced (radiation heat transfer still exists, but there is no heat conduction and heat convection), most of the heat can only be transferred to the water in the glass tube, so that the water in the glass tube is heated.

The heated water becomes lighter and enters the thermal insulation storage bucket along the heating surface of the glass tube, and the water with relatively low temperature in the barrel enters the glass tube along the backlit surface of the glass tube to replenish, so that the water in the thermal insulation storage bucket is continuously heated, so as to achieve the purpose of hot water.

Answer: If the solar energy is with a controller, it may be that the temperature probe is broken, if the solar energy is with a float on the water, it should be that the float is broken, and it is not dead Note: When it is found that the cold water is strung up through the hot water pipe, the solution is to turn off the valve of the hot water pipe when the hot water is not used.

What is the reason why the overflow pipe of the solar water heater keeps flowing water?

If the solar energy is with a controller, it may be that the temperature probe is broken, if the solar energy is with a float on the water, it should be that the float is broken, and it is not dead Note: When it is found that the cold water is strung up through the hot water pipe, the solution is to turn off the valve of the hot water pipe when the hot water is not used.

There is also a possibility that the float is broken.

If the solar energy is equipped with a controller, it may be that the temperature probe is broken, and if the solar energy is brought to the water with a float, the float should be broken and cannot be turned off. When it is found that cold water is flowing up through the hot water pipe, the solution is to turn off the valve of the hot water pipe when the hot water is not in use.

The solar water heater first feeds the cold water into the hot water storage tank, and then transports the heat through the collector to the insulated water tank. The hot water storage tank is connected to the indoor cold and hot water pipelines, so that the whole system forms a closed loop.

Routine maintenance. 1. When installing a solar water heater, there may be dust or oil smell in the water pipe, and you can open the faucet to remove debris when you use it for the first time.

2. The water stored in the solar water heater should be discharged regularly according to the local water quality conditions, and the drainage time can be selected in the morning when the collector is at a lower temperature.

3. The surface of the solar water heater should be wiped regularly according to the amount of dust falling in the area, and it can be cleaned by itself when it rains, and the surface of the water heater can be kept clean to obtain a higher heat collection efficiency.

4. When you don't use hot water for many days on sunny days, the hot water temperature is very high, please turn on cold water first, and then hot water when using the solar water heater to avoid scalding.

5. There is a filter screen device at the outlet of the faucet, and the scale and debris in the water pipe will gather in this net, which should be removed and cleaned regularly, so as to increase the smooth flow of water.

6. In winter, it is very common for the pipeline to be frozen, such as finding that the pipeline has been frozen but the pipeline has not yet cracked, and it can be automatically dredged after the temperature rises. You can also use a hair dryer to blow it, or wrap the water pipe with a towel, and then pour it slowly with warm water, and do not use fire to bake, knock on the pipe or use boiling water to scald, which will burst the pipe. Repeated freeze plugging can easily cause the pipeline to freeze and crack, so it is necessary to strengthen the pipeline insulation measures.

7. Solar water heaters need to be cleaned, inspected and disinfected every two to three years on average, and users can also do some disinfection work by themselves, such as buying some chlorine-containing disinfectants and pouring them into the water inlet, allowing them to soak for a period of time, and then release them, which can have a certain disinfection and sterilization effect.

8. The inside of the vacuum tube needs to be cleaned in two to three years on average in the solar water heater to prevent the scale inside the vacuum tube from affecting the heat absorption effect.

9. If the solar water heater is equipped with a special instrument, pay attention to lightning protection and electricity protection, and do not take a bath and unplug the electric heating plug when thundering.

1. Leakage caused by obstruction and corrosion of mixing valves, pipelines, safety valves and other accessories of water heaters.

2. Water leakage caused by the rupture of the mixing valve, pipeline, safety valve and other accessories of the water heater.

3. The sealing gasket of the mixing valve, pipeline, safety valve and other accessories of the water heater is aging and cracked, and the water leakage is caused by the failure to achieve the sealing effect.

4. Water leakage caused by rupture of the inner tank of the water heater. The best way to avoid this is to protect the liner from corrosion, and to clean and maintain it regularly. For example, if you need to clean the water heater every one or two years to prevent the breeding of scale, you can effectively extend the service life of the water heater.

Precautions for the use of solar water heaters.

If an auxiliary heat source is installed, the auxiliary heat source device and heat exchanger should be checked regularly to see if they are working properly. For the auxiliary heat source is heated by an electric heating pipe, it is necessary to ensure that the leakage protection device works reliably before use, otherwise it cannot be used. Special attention should be paid to water supply when using auxiliary electric heating, and the water volume in the water tank should not be less than 50% to prevent dry boiling without water.

When taking a bath, special attention should be paid to unplugging the power plug, and it is strictly forbidden to use it with electricity.

Clean the liner regularly, after long-term use due to the long-term precipitation of trace impurities and minerals contained in the water, if not cleaned regularly, it will affect the quality and service life of the effluent.

1. It may be because of the mixing valve, pipeline and safety valve, these fittings are blocked, which will cause a large area of leakage.

2. It is also possible that it has been used for a long time, and there is a rupture, for example, the sealing gasket is aging, and the sealing effect cannot be achieved, which will also cause water leakage.

3. Another reason is that the inner tank of the water heater, if it is ruptured because of the temperature difference, it will also cause the overflow port to slowly seep water, if it is because of the failure of the mixing valve or pipeline, including the safety valve and other accessories, you can directly replace the relevant accessories to solve the problem.

Precautions for the use of solar water heaters.

The stored water in the solar water heater needs to be discharged regularly to avoid pollution caused by long-term water accumulation. The discharge cycle is determined by the local water quality conditions, and the discharge can be done in the morning when the collector temperature is lower.

Turn on cold water and then hot water: If it is sunny for many days and no hot water is used, the water temperature will be relatively high, so you need to turn on cold water and then hot water to avoid scalding.

There are many reasons for this situation: 1: the water level sensing probe is malfunctioning, 2: whether a new water heater has been installed recently, etc., has caused the pipe to be scanned, etc. 3: This is set in the meter.

Recommended" "Dr. Sun" solar, three-bin model (no need for water level sensing probe and solenoid valve), heating and hot water utilization rate in rainy weather are fast, and the after-sales rate is also greatly reduced, which saves time and electricity.

The water supply valve is broken, 100% yes.

When the water is full, just stop the water.

The steam came out of the water heater.

What should I do if the water heater does not have water on it, and it runs as soon as it is on the underwater water pipe.

The reason for this is that the elbow is directly connected to the overflow pipe. 2.Valve damage:

If the water supply valve is damaged, drain the water in the solar energy, and then turn on the shower to close the water supply valve. 3.Tube freeze cracking:

Many solar tubes are frozen in winter. 4.Notes:

The solar water heater cannot be put into the water, and to stop using the equipment, ask a professional to deal with it.

1. It may be due to thermal expansion and cold contraction, which is due to the overflow pipe directly connected to the elbow. The normal one is generally a tee, and the water vapor will be discharged into the air through another hole, and will not condense into water dripping, and it will not drip on cloudy days or without sun. 2. The water valve is broken, put the solar water out, and then open the shower to close the water valve, if the valve is bad, the shower will drip slowly.

3. Many solar winter tung barrage days are frozen and damaged pipes, that is, because of the slow water, so the water pipes are frozen and cracked, and most people do not pay attention to think that it is not a problem with the valve.

1. The return pipe of the solar water heater is an overflow pipe, and the overflowed water flows out through this pipe after being filled with water, and it is reasonable that the flow should stop after a while, but in sunny weather, the solar energy is constantly heating, the water temperature is rising, and the water is expanding and shrinking above 4 degrees, and the water level in the solar water tank will rise slowly, higher than the overflow port, so there is water flowing out, giving people the feeling that it is always flowing water. In fact, it is a normal phenomenon.

2. You are too full on the water, after the daytime sunshine, due to the reason of thermal expansion and contraction, the water may be dripping during the day, and the water is not hot, that is, the water valve of your home is not closed strictly (it needs to be replaced) or there are places where hot and cold water are channeling each other. I hope it can help you, thank you for your support, come on!

If there is a small drop of water falling in the summer, it may also be caused by the thermal expansion of the water in the tank.

Check if the water switch has been on the water, I really help you look forward to it

1. The return pipe of the solar water heater is an overflow pipe, and the overflowed water flows out through this pipe after being filled with water, and it is reasonable that the flow should stop after a while, but in sunny weather, the solar energy is constantly heating, the water temperature is rising, and the water is expanding and shrinking above 4 degrees, and the water level in the solar water tank will rise slowly, higher than the overflow port, so there is water flowing out, giving people the feeling that it is always flowing water. In fact, it is a normal phenomenon.

2. You are too full on the water, after the daytime sunshine, due to the reason of thermal expansion and contraction, the water may be dripping during the day, and the water is not hot, that is, the water valve of your home is not closed strictly (it needs to be replaced) or there are places where the hot and cold water are different from each other.

It's because, first, the switch on the water supply is broken; Second, the water is too full.

The first case is when the valve is broken. First check the valve to see if there are cracks or dripping, if there is, please switch the water source master and replace the valve. In the second case, if the valve is not broken, it is because the water is too full, and it overflows after heating and expansion after being filled with water, and it will not drip when it is released after it is full.

When the sun comes out, the heat convection will quickly expand the water in the water heater, and the expanded water will overflow from the return pipe. This situation is not a "problem", and once the water temperature reaches its maximum value, it does not continue to overflow. You can also take the initiative to use it to grind some indiscriminately, and it will stop dripping immediately.

Lucky friends. As for the specific situation, the water switch of the solar water heater is controlled by two ceramic sheets, and if there are tiny sand particles between the ceramic sheets, there will be leakage. If you have hands-on ability, you can fix it yourself. First close the main water pipe, clean the water heater and store water, remove the fixing screw from the water switch cap, remove the switch handle, unscrew the switch body with a wrench, remove the ceramic sheet and clean it, adjust the rubber gasket at the top, and then install it back to solve the problem.

If you lack the relevant knowledge, you have to pay a professional to repair it.