How to overclock the E6550 to be detailed

Here's how to overclock the e6550:

3. Click the clock voltage in the "Performance Control" menu on the left, click the mouse, there is a box of clock frequency in the lower left corner, there is an HT reference frequency in the box, this is the external frequency of the CPU, click the mouse to hold the sliding box, move slowly, generally increase by 5, the incremental value is as small as possible, because after all, the load of overclocking on the CPU is relatively large;

4. After increasing the value of the HT reference frequency, check whether the target frequency has increased, click the application in the lower right corner, the interface will be stuck for a while, if the frequency of overclocking is too high, the computer will restart directly, so the frequency of overclocking should be increased slowly, make sure that the CPU can withstand it, and then slowly increase the frequency;

5. After the adjustment is completed, click Apply, and then click OK to finish.

Ignore the memory and go straight to the BIOS. CPU frequency = main frequency x frequency multiplication. Normally, overclocking can only be adjusted to the main frequency. Refer to the specification for specific projects.

Back to ls....Now the DDR2 800 has a hard life. So that amplitude shouldn't be a problem.

1.Intel Xeon E5620, 4 cores and 8 threads, clock speed, turbo up to the first generation Core i7 920, Core i7 950, etc., use the same architecture.

2.The main frequency of the E5620 itself is relatively low (because it is set very conservatively to ensure stable operation for a long time in order to be used on the server, but based on the excellent constitution of Xeon, it is very easy to overclock the E5620).

3.Turn off the Turbo Mode in the BIOS (Disableable), directly adjust the external frequency to, the frequency doubling X19 (non-adjustable), the core voltage is the default, no need to adjust, so that you can easily overclock the E5620 to, run completely stress-free, no need to replace the fan, the operating temperature almost unchanged, very stable. After overclocking, the E5620 can basically reach the level of the Core i7 970.

4.You can even try to adjust the external frequency to 220MHz, at this time you can overshoot the E5620, and there is no need to replace the fan, the operating temperature is a little higher (more than 65 degrees), but the operation is still very stable.

Little brother: Are there any specific steps for overclocking?

I was able to overclock the E6700 up to the core clock, but the system became unstable at this point, and the stability of the system with the Thermalright XP-120 heatsink was still problematic when the core clock was overclocked, but I did some benchmarking on this frequency despite this. The last core clock seems to be the best choice, and although there are still some minor issues with the system after long runs, the impact is almost non-existent.

And when I further reduced the core frequency, the whole system ran very stable, and the overclocking amplitude of up to 1G also brought a huge improvement in performance, according to reports, some people have already exceeded the core frequency of the Core 2 Duo E6700 to 4G, and the 4G core frequency is obtained based on the use of water cooling and heat dissipation, which is overclocking with no practical value.

Can be overclocked to.

The parameters of Intel E6700 are as follows:

Basic parameters: applicable type desktop;

CPU Series Core 2 Dual-Core;

CPU Frequency:

CPU frequency;

External frequency 266MHz;

doubling 9 times; Bus frequency: 1066MHz;

CPU slot:

Slot type LGA 775;

The number of pins is 775pin;

CPU core:

Core code name Conroe;

CPU architecture: EM64T;

Number of cores: Dual cores;

The manufacturing process is 65 nanometers;

Thermal Design Power Consumption (TDP) 65;

core voltage; CPU Cache:

L1 cache 128;

L2 cache 2MB*2;

Technical parameters: instruction set MMX SSE SSE2 SSE3 SUP-SSE3 EM64T;

Hyper-Threading technology is not supported.

Paired with GIGABYTE G41MT-S2

My Pentium e6700 was successfully overclocked to (external frequency 333 * octave 12 = power supply needs to be a little better.

Bubalus Buffalo Swift Bull 3300 (PE400AAA) Desktop Power Supply (Rated 300W Active PFC 80Plus White Label Support Backline)

Master Lu temperature is kept between 27-30 degrees. At the moment the office is used for 2 hours, everything is OK

This is mine.,According to what I said downstairs, I should be the air-cooled overclocking limit.。。。 In fact, it also depends on the physique of the U and the motherboard.,My previous motherboard can only be over-the-top at the most.,The board is broken.,Replace a piece to be over-the-top.。

Overclocking up one level, not bad overclocking up two levels, barely overclocking up three levels, don't be afraid of burning, just try.

How much you can get depends on your overall mix and set-up method.