What do you need to pay attention to when changing the Mercedes Benz E260 brake pads

Just change it directly, pay attention to the new film to change the sensor [If there is a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

Hello, nothing, an experienced master can replace it for you. [If you have a problem with the car, ask the car master.] 4S shop professional technician, 10 minutes to solve. 】

First of all, it is necessary to check whether the brake pads replaced by the road sweeper are pure accessories, and Zhonglian automobile brake pads remind everyone to see the integrity of the product packaging, the anti-counterfeiting mark and the packaging logo are consistent with the logo on the brake pad, and whether the product model is consistent with the content of the certificate. Before lifting the vehicle, the cover containing the brake fluid should be opened and the tire screws should be loosened at the corners. If a simple jack is used, the jack should be supported and the wheels that do not replace the brake pads should be reinforced.

Remove the tire, loosen the clamp body fastening screws, and check the screws and pliers sliding guide rod, remove the sediment and oil on it, and apply lubricating oil for maintenance. Remove the old brake pads and check the wear of the brake disc for groove and deterioration. Severe wear and tear should be replaced with new brakes.

Hello, go to 4s to replace it, put the tires on [car problems, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

You don't need to pay attention to anything about the front brake pads of this car, you should pay attention to the decoding of the electronic handbrake in the back, and there is the line of the sensor [If the car has a problem, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

Mercedes-Benz E260L brake pads can be used for more than 30,000 kilometers, without fixed replacement cycle time, and TRW brake pads are selected. The front brake pad model specification is A0054200820, and the rear brake pad model specification is A0064206120.

Mercedes-Benz E260L brake pad replacement example tutorial.

Warm reminder: Mercedes-Benz E260L rear wheels contain electronic parking system software, only with the on-board computer can the brake pedal cylinder be retrieved, and then the brake pads can be replaced with special tools for disassembly. The front tire can be immediately disassembled and assembled with special tools, and is not necessarily operated according to the on-board computer.

The following is an example of the latter round.

Connect the computer car with versatility, select "Turn on the rear brake pedal cylinder" on the brake pad replacement setting page, and after about 5 seconds, the cylinder will get rid of the success, and then the service brake motor will retract.

Note: Be sure to open the outer cover of the booster oil can, because the sub-pump is retracted, there will be a situation where the booster oil will flow back. ）

Twist the two screws of the brake caliper, and if the sub-pump is completely separated, it can be smashed open with a slotted screwdriver.

At this time, you can remove the brake caliper Xiaohong cover, and you can install new brake pads. There is one side of the production of text messages on the outside, and the side without words rushes inside.

After settling down, use the computer again to set [turn off the rear stool wheel brake pedal cylinder], and the brake motor will be calibrated after a few seconds.

Millions of car purchase subsidies.

Summary. Dear, glad to answer for you! Mercedes-Benz E260 after replacing the front and rear brake pads, the front and rear brake alarm lines are still bright, check the brake pad wear is because of the tire change deflated, so the tire pressure control system is misjudged, such as insufficient air pressure, etc., and then after the tire change model, the air pressure will cause an alarm, so it needs to be matched, I hope it will help you.

Mercedes Benz E260 replacement brake pad reset.

Mercedes-Benz E260 After replacing the front and rear brake pads, the front and rear brake alarm lines are still bright, and the brake pads are still bright, check the brake pad wear.

Dear, glad to answer for you! Mercedes-Benz E260 after replacing the front and rear brake pads, the front and rear brake alarm lines are still bright, check the brake pad wear is because of the tire change deflated, so the tire pressure control system is misjudged, such as insufficient air pressure, etc., and then after the tire change model, the air pressure will cause an alarm, so it needs to be matched, I hope it will help you.

Expand your information; Check the brake pads to see if they are there, and then check whether the brake pad induction line has touched.

I didn't change the brake pads before, I didn't change the brake pads before, because there were no brake pads, the front and back were changed, the sensor line was changed before and after, and now it's still the same alarm.

It may be that the electronic system has not yet been detected.

You can also go to the 4S store for troubleshooting.

Mercedes-Benz E260L brake fluid replacement time is 2 years, using **Mercedes-Benz original well-known brand, model specification DOT4.

Ben Kuxu Shi Chi E260L brake fluid replacement example tutorial.

1. The brake fluid must be pressed by a pot. It is advisable to try not to use the original trampling method, which will leave the brake fluid behind.

2. Draw the brake oil from the brake oil pot in the cabin first, and the actual operation can be carried out in about 10 seconds.

3. Then use the oil drum of the pumping machine to extract the residual oil and gas in the pipeline of the rear tire brake pump.

4. Connect the soft rubber hose to the exhaust hole, and the brake fluid can be extracted. (Note: The key depends on the location of the exhaust hole, decide whether it is necessary to remove the wheel to carry out the plastic hose connection, if the exhaust hole is installed on the inside of the wheel to remove the wheel, the external exhaust hole can be extracted immediately.)

5. While pumping the brake fluid, pour new car oil into the refill port. That's because the old oil is pushed out with new oil, and at the same time the pipeline is not run out of oil, which in turn frees up a lot of gas.

6. The whole process of extraction generally takes ten minutes, and the actual operation of extraction can be completed. Then add the brake fluid to the appropriate scale range again, cover the brake oil cap, and run the module to check the actual effect. After pressing the pedal several times, I felt weak and discharged the gas again.

Millions of car purchase subsidies.