What color is good for built in decorative cabinets

The first is measurement, which must be measured in advance to determine how many baseboards are needed to avoid material waste.

Cut the baseboard.

Since the baseboard cannot be the same size as the wall, it needs to be truncated and spliced. After measuring the distance, use a pencil or knife to draw a cutting line on the baseboard and cut it off with a sawtooth.

Baseboard mounting.

If it is a tile floor, we install the baseboard installation method nailed on, if the floor is paved, a certain gap will be reserved between the floor and the wall, the baseboard will be stuck into the gap first, and then nailed on.

1. Drilling: Use special tools to drill holes in the wall, and observe whether there are water and electricity lines in the wall before drilling to prevent mistakes. The common length of the baseboard is 2m, in order to fix the baseboard more firmly, the interval of the drilled holes should be about 40cm, and the interval at the interface should be a little smaller.

After drilling the hole, nail the small wooden strip into the hole. The nails that hold the baseboard are nailed to this wooden strip, and the reason why they are not directly nailed to the wall is mainly to prevent the nails from loosening.

2. Fixation: Before fixing the baseboard, the wall should be leveled and cleaned, otherwise the baseboard cannot be completely attached to the wall after it is installed, and it will leave an unsightly gap. Look for the position of the drilled hole and secure the nail to the baseboard.

When fixing, pay attention to whether the baseboard is close to the wall, and the nail should be completely driven into the hole to avoid affecting the effect.

3. Corner connection treatment: put the baseboard flat, cut the sawtooth and baseboard at a 45-degree angle, and then splic. In addition:

It is also said that the corner junction of the baseboard cannot be simply connected by 45 degrees. Since the wall has a certain moisture content, a simple 45-degree connection will bulge (thermal expansion and cold contraction) because there is no void when the baseboard expands. The correct safety method should be to lay one side upright and leave a proper expansion gap at the junction with the wall, while the other side should be shaped 45 degrees straight up to join it.

Then check. When inspecting, it should be noted that the baseboard should be completely close to the wall, leaving no gaps, and for the places where the baseboard cannot be installed, the edge can be closed with a trim strip.

In short, the baseboard plays the finishing touch to the entire interior decoration; So it's even more certain that the baseboard is an essential part of the decoration! However, the installation and construction of the baseboard is very important.

Embedding in there, huh? Generally, it is done by stitching, or the material on top is cut and seamed, and the material to be highlighted is passed through the seam.

Please embed in**? What is the size of the embedding area?

First of all, measure the size in advance and decide how large the closet size is according to the size of the house.

Unlike other furniture products, it is not placed directly, but embedded in the wall. Therefore, it is crucial to consider the design size in order to make the best use of the closet and present advantages. It is worth saying that according to the advice of professionals, it is a good choice to make a built-in closet in the living room wall, which can make the role of the closet be reflected to the greatest extent, and can also increase the aesthetics of the living room and strengthen the decorative role.

Secondly, it should be designed by professionals and constructed by professional decorators.

Some people will choose to decorate and construct by themselves, but the fact is that for inexperienced people, it is quite difficult to design a closet, and it is difficult to design a closet with a good style and strong practicality. Therefore, hiring a professional designer is very helpful in designing a closet that is stylish, unique, and practical. Not only that, but hiring a professional,** is not as expensive as one might think.

Built-in balconies are built-in balconies with exterior walls that are about the same width as the room, and most of them have relatively wide openings. The advantage is that the balcony is large and the room has a wide view. Disadvantages: performance insulation handicap.

When decorating, you can decorate it into a leisure space according to your own aesthetics, or you can set up a small landscape (waterscape, rockery, plants), and then install a lifting drying rack to have many functions.

Hello, I am a professional consultant of Vanke Real Estate, the built-in balcony is actually a built-in balcony, some of Vanke's real estate is a built-in balcony, it can be changed into a small room or pantry, study and computer room, the advantages and disadvantages depend on your own situation, it is not easy to say. Hope it helps.

1. Open the box and check whether the speaker is damaged to ensure that the product is complete.

2. Open the packing box, the audio and the grille are arranged in it, and the manual, screws, and mounting and fixing frame are all on the carton in the grille.

3、You can make the speaker fit to the wall or hole in different layers,It can be completely embedded installation,The cabinet can be outside or inside the wall,Change the direction of the installation accessories to let the speaker be directly wall-hung on the outer wall,You can even do floating installation。

4. The final installation is completed.

1, the living room ceiling speaker line layout is best done with the electrician wiring, because the speaker line is weak current, so can not be too close to the electrician's strong current (AC220 volts), there is a PVC pipe, the distance of 20cm can be, these are to avoid the emergence of interference factors, but the overall wiring route should try to follow the weak current route or strong current arranged by the electrician, to avoid clutter, and the electrician wiring will generally leave the maintenance port, the speaker line should be different from other lines, so that it is convenient to distinguish it clearly when overhauling in the future.

2. The PVC pipe of the speaker line can be fixed on the ceiling bar, and the position of the speaker point and other lights in the actual construction process should be considered, the position of the fire sprinkler, the air conditioning outlet, and the shape of the ceiling capping.

3. The speaker wire wears PVC, and the PVC pipe is bent by spring to ensure that the wire in each pipe can twitch freely from the junction box, and it is also convenient for future maintenance, threading and wire change. Usually the electrician waits for the painter to finish painting before installing various lights, which also avoids a lot of trouble.

In fact, the embedded surround speaker has many benefits, not only can it save space, but also decorate the ceiling, and the important thing is that it can also use the ceiling to insulate sound, and can even solve the problem of sound diffraction and cabinet vibration, which is perfect. However, the installation technology is more difficult, and you need to find a professional livable intelligent audio-visual company to install it, after all, it costs so much money, and you still want to get good results.

If the home is well decorated and you are ready to buy a built-in oven, you can consider customizing a cabinet in the kitchen, living room or dining room, with an oven embedded in the middle cabinet and a drawer underneath.

As modern people pay more and more attention to the pursuit of quality of life, spacious kitchens in addition to the necessary pots and pans for life, the demand for all kinds of kitchen appliances has also increased significantly, good brand kitchen appliances are both cost-effective and fashionable, and do not have to worry about the safety of the tip of the tongue, so many consumers pay more and more attention to the choice of kitchen appliances, and household electric ovens just meet people's needs in this regard. Electric oven home baking has realized the great transformation of food from extensive processing to fine creation, not only baked food is delicious, but also brings endless fun to life, and has since become the new favorite of many ordinary families. However, there are many kinds of electric ovens on the market, small ovens, built-in ovens, ovens of different brands, different functions, and different prices have dazzled many consumers, and they are also baking, so what is the difference between small ovens and built-in ovens, and what aspects should be considered to choose an oven that you are satisfied with?

Let's focus on the analysis.

As long as there is space, you can decorate it after opening the hole.

You can also make a middle cabinet for a built-in oven, with an oven on the top layer and mold tools on the bottom layer.

If you make a whole cabinet, it is basically a standard unit. You can change the cabinet.