An Android robot and an exclamation mark appear and get stuck directly

I'll talk about my own solution experience,After my Motorola me865 was upgraded,I rooted it,And then in the process someone pulled my data cable down,Caused the phone touch screen to react super slowly,After entering recovery,There is a robot and an exclamation mark lying on the screen,And then I gave it a double wipe,It's good to restart it,I'm very happy,I hope it will work for you。 Double wipe method subordinate:

1. Turn your phone off.

2. Press and hold the two buttons on the volume up and down the volume without loosening, and then press and hold the power button.

3. In the pop-up interface, use the down button, select recovery, press the upper button to confirm, until there is a yellow triangle symbol, and you will enter recovery mode.

4. Press and hold the volume up and volume down buttons at the same time, 5. Use the down tone key to select "wipe data factory reset", then use the power on and off button to confirm, then select "yes delete all user data", and then turn the power on and off button to confirm to wipe

6. Share the common instructions in recovery:

Reboot System Now

Wipe Data Factory Reset (and wipe out all data).

This is by holding down the volume- button and the power button to turn on... Go to recovery, tap the bottom right corner of the screen, or press and hold volume + and volume - at the same time, select the option to reboot... If the touch screen is valid, touch the screen to click the operation, if the touch screen is invalid, the volume button corresponds to up and down, and the power button is OK.

If you don't press the volume- and power button to enter recovery, it may be a problem with the system, and it is recommended to re-flash the machine.

I have no choice but to go to the local area to brush up on the machine.

If there is a problem with the system, just re-flash the machine.

Shuangqing give it a try.

Shuangqing tutorial, which is used to clear the lock screen password, and remove multiple software flashback problems caused by flashing.

If you can, use the backup software that comes with your phone to back up.

Shuangqing needs to enter the REC mode of the mobile phone, and there are two ways to enter.

1. Click System Update, click the menu key to select Restart to Recovery, click OK, and the phone will reboot into Recovery mode.

2. In the shutdown state (buckle battery shutdown), press and hold the power button and the volume down button at the same time (the mobile version of the Redmi 1s is the volume down button, and the Unicom telecom version of the Redmi 1s is the volume up button!) ), light up the screen and release the buttons.

Then you'll see three options.

Recovery mode means to enter REC mode.

fastboot mode means to enter the wire brush mode.

norma boot means reboot.

At this time, the volume down button is the selection key, the volume up button is the OK key, and the power button is useless.

Press the volume down button to move the cursor to recovery mode, then press the volume up button to confirm, and wait for a few moments for it to appear.

A green android robot lying on the ground, finally press the power button to enter.

At this time, the volume up button is the confirmation key, and the volume down button can be selected to start double clearing.

3.Select [Wipe Data Factory Reset] yes -

4.Select [wipe cache partition] yes -

5. Wait for the progress bar to end, press Back, select [Reboot System Now], and the phone will start to restart automatically.

This is no command**, long press the power button for ten seconds to force restart and it will be fine.

In this case, there is usually a problem with the system, and the solution is as follows:

1. Shut down first, then press the volume plus and the power button at the same time to enter recovey mode, and perform the double clearing (in the recovery interface, select Wipe Data Factory Reset and Wipe Cache Partition).

3. If the above methods are invalid or cannot be turned on, it is recommended to send the mobile phone to the official after-sales service center, and the engineer will help check and deal with the boring section.

Reboot it, or re-rinse it.