ghost batch installation of LAN system, detailed steps

You need to prepare three files and copy them to the C drive

The first one is ghost software: go to the server-side ghost installation directory and find it.

The third is the workstation network profile: created with a notepad or program, which reads as follows:

IP= Workstation IP, which must be unique and modified separately on different workstations.

netmask= Subnet mask.

gateway= Network clone server IP address.

Then go to the BIOS in the 100 computers and select the boot device as the network card. Set the LAN boot ROM to Enable

Burn a ghost disc to use the virtual drive format, have a virtual drive software, back it up on one computer and share it, install the virtual drive software on the operating system on the other machine, and run the ghost disc (virtual disc format) to install it.

Yes, but if you want to change the computer name, IP address, etc., just change the installation bootloader.

There is professional software, search for it online!!

Still cloning with ghost networks? Here, teach you to directly back up the system to the network and network cloning.

First of all, back up the host as GHO, and then go to the **maxdos7 network engraving tool, which has the server side and pxe If the submachine can be started on the network, use the network start. If not, use the boot disk of MaxDOS7 to boot, and the DOS network card driver of the handset will be automatically installed after startup.

It can be installed, provided that the server is set up, all computers are connected to the server through the LAN, and then set the computer pxe to start, and burn the gho image of the server to the local C disk with the network engraving tool.

Clone the GHOST system through the PXE batch network.

november 8, 2011

Doing this is actually a favor for a friend, there are dozens of computers that need to install a new system, the time is very tight, only less than 1 day, one by one installation is obviously very unreliable, so I tried this method.

Tools Needed:

Deepin Internet Café assists Ghost for Pxe

The GHO file of the ghost installation disk.

Installation process: First, of course, first of all, connect all computers to the power supply, connect to the switch, build a good local area network, and ensure that each computer is connected smoothly;

2. Use a computer that has installed the system as the server, install the auxiliary tools of Deepin Internet Café, copy the GHO file to the computer, start PXE, and configure the PXE server

Disposition. This is used to assign IP addresses, first, pay attention to the IP address and the network card IP in the same network segment, and second, the assigned IP should not conflict with the computer in the current network;

Click on the "dhcp" tab to set the start and end addresses, and the boot file is.

Then click "Options" in the upper right corner of the software to set the machine name and gateway DNS, etc., after all are completed, click "Save" in the upper right corner of the software, and click "Enable DHCP" to start the service;

2.Netgram service configuration.

Click on the "NetGram Service Configuration" tab, select "Restore Image" as the method, and set the image file path;

Click "Partition Clone" below, the default is the first partition of the first disk, and finally click "Start Ghostsrv";

A window will pop up, don't close it, move on to the next step.

<> restart, press shift+f10 to enter the following interface, and press f4 to save and exit after setting.

The client PXE has booted successfully.

Automatic selection of PXE drive mode.

Automatically selects the cloning mode.

Enter the ghost waiting page.

Fourth, the process of ghost netkeeping, which only takes a few minutes.

All clients are ready, waiting xx session to start is displayed below ghost, and the number of clients on the server side is displayed correctly, then click "Send" on the server side.

Things to look out for:

1. Some motherboards do not need to be set up, and you can enter the PXE interface when you boot up;

2. Due to the new installation, some computers may have hardware problems, which need to be solved in the early preparations;

3. When setting up the PXE server gateway, you need to wait for a few minutes, and when the computer connection is normal, it means that the IP settings of the server are available;

4. Some computers will be stuck in the process of network grams, so you need to pull out the network cable of the computer and install it separately;

Find a machine to install ghostsrv and then put a master disk image to this machine, remember the IP of this machine, and then prepare 10 USB flash drives, make an environment that can start ghost, and use ghost to remotely pull the image to install the system. (U disk boot disk is of course the more the better).

Of course, you need to get your computer's hard drive partitioned first, and then learn how to use Ghostrv

When I was studying, my teacher taught me, but I forgot it.